Icom IC-7100 Advanced Instructions
Icom IC-7100 Manual
 |
View all Icom IC-7100 manuals
Add to My Manuals
Save this manual to your list of manuals |
Icom IC-7100 manual content summary:
- Icom IC-7100 | Advanced Instructions - Page 1
FUNCTIONS FOR RECEIVE 6 FUNCTIONS FOR TRANSMIT 7 D-STAR INTRODUCTION 8 D-STAR OPERATION 9 D-STAR OPERATION 10 GPS/GPS-A OPERATION 11 MEMORY OPERATION 12 SCAN OPERATION 13 USING AN SD CARD 14 VOICE MEMORY FUNCTION 15 VOICE TX FUNCTION 16 ANTENNA TUNER OPERATION 17 SET MODE 18 DATA - Icom IC-7100 | Advanced Instructions - Page 2
About these Advanced Instructions (PDF format) These Advanced Instructions describe the details of the IC-7100 features. This PDF formatted manual provides you with convenient functions, as follows. NOTE: Below page is used only as an example to describe these advanced instructions. Move to - Icom IC-7100 | Advanced Instructions - Page 3
search screen or advanced search screen. • Printing out the desired pages. Click "Print (P)" in File menu, and then select the paper size and page numbers you want to print. *The printing setup may differ, depending on the printer. Refer to your printer's instruction manual for details. *Select - Icom IC-7100 | Advanced Instructions - Page 4
function's instructions for further details. Frequency (MHz) Frequency (kHz) Frequency (Hz) Operating mode Filter No. VFO mode/ Memory mode DDTouch screen precautions Briefly touching the controller's touch . Meter type Touch key for each function. (Example: M-1 menu is selected.) iii - Icom IC-7100 | Advanced Instructions - Page 5
Section 1 PANEL DESCRIPTION Controller - Front panel 1-2 Controller - Function display 1-8 Controller - Multi-function keys 1-11 DDM-1 (M-1 menu) Display 1-11 DDM-2 (M-2 menu) Display 1-11 DDM-3 (M-3 menu) Display 1-11 DDD-1 (D-1 menu) Display 1-11 DDD-2 (D-2 menu) Display 1-11 DDFunction - Icom IC-7100 | Advanced Instructions - Page 6
Controller - Front panel q w PWR AF RF/SQL TX / RX CLR M-CH BANK i7100 PBT RIT RIT TUNER/CALL MENU NB NR MIC/RF PWR SPEED/PITCH P.AMP ATT NOTCH DR SET QUICK AUTO TUNE RX�CS SPEECH XFC MPAD q P OWER SWITCH•AF VOLUME [PWR]•[AF] (p. 3-2) ➥➥Push to turn ON the transceiver power - Icom IC-7100 | Advanced Instructions - Page 7
. ❍ When the PBT LED lights green (Mode: SSB/CW/RTTY/AM) ➥ R otate to adjust the receiver's IF filter pass- band width using the DSP circuit. ➥ H old down for 1 second to reset the PBT set- tings. • The PBT is adjustable in 50 Hz steps in the SSB/ CW/RTTY modes, and 200 Hz in the AM - Icom IC-7100 | Advanced Instructions - Page 8
CLR M-CH BANK PBT RIT RIT TUNER/CALL MENU NB NR MIC/RF PWR SPEED/PITCH P.AMP ATT NOTCH DR SET QUICK AUTO TUNE RX�CS SPEECH XFC MPAD o !0 !1 !2 !3 !4 o ANTENNA TUNER/CALL KEY TUNER/CALL ❍ ANTENNA TUNER KEY Operation (p. 16-4) (Frequency band: HF/50 MHz) ➥ Push to turn an optional - Icom IC-7100 | Advanced Instructions - Page 9
BANK PBT RIT RIT TUNER/CALL MENU NB NR MIC/RF PWR SPEED/PITCH P.AMP ATT NOTCH DR SET QUICK AUTO TUNE RX�CS SPEECH XFC MPAD !5 !6 !5 P REAMP•ATTENUATOR KEY P.AMP ATT ❍ PREAMP KEY Operation (p. 5-2) (Frequency band: HF, 50/70 MHz) Push to select one of two receive RF preamplifiers, or to - Icom IC-7100 | Advanced Instructions - Page 10
to enter or exit the SET mode. • "Voice Memo," "Call Sign," "RX History," "DV Memory," "My Station," "DV Set," "GPS," "SPEECH," "QSO/RX Log," "Function," "Tone Control," "Connectors," "Display," "Time Set," "SD Card" and "Others" set group are selectable. !9 QUICK MENU KEY QUICK ➥ Push to open - Icom IC-7100 | Advanced Instructions - Page 11
Previous view 1 PANEL DESCRIPTION Controller - Front panel (Continued) PWR AF RF/SQL i7100 TX / RX CLR M-CH BANK PBT RIT RIT TUNER/CALL MENU NB NR MIC/RF PWR SPEED/PITCH P.AMP ATT NOTCH DR SET QUICK AUTO TUNE RX�CS SPEECH XFC MPAD @5 @4 @2 @3 @2 SPEECH•LOCK KEY SPEECH ❍ SPEECH KEY - Icom IC-7100 | Advanced Instructions - Page 12
in 10 Hz or 1 Hz steps. u GPS ICON (p. 10-2) ➥ Appears when valid position data is received from a GPS receiver that is connected to the [DATA1] jack. ➥ Blinks when invalid data is received from the GPS receiver. i SD CARD ICON ➥➥" " appears when an SD card is inserted and " " alternately blinks - Icom IC-7100 | Advanced Instructions - Page 13
. • Push MENU to change the set of functions assigned to the touch keys. • Toggles the function display menu between M-1, M-2, and M-3 menus or D-1 and D-2 menus. !8 MULTI-FUNCTION METER INDICATION ➥➥Displays the signal strength while receiving. ➥➥Displays the relative output power, SWR, ALC or - Icom IC-7100 | Advanced Instructions - Page 14
(p. 12-16) ➥➥" " appears when the VSC (Voice Squelch Control) function is turned ON. (Mode: DV) ➥➥" " appears when the EMR (Enhanced Moni- tor Receive) communication mode is selected. (p. 9-10) • In the EMR communication mode, no call sign setting is necessary when operating in the DV - Icom IC-7100 | Advanced Instructions - Page 15
view 1 PANEL DESCRIPTION Controller - Multi-function keys ➥➥Push MENU to change the set of functions assigned to touch keys. • Toggles the function display menu between M-1, M-2 and M-3 menus or D-1 and D-2 menus. • Functions vary, depending on the operating mode. • In the DR mode, the D-1 and - Icom IC-7100 | Advanced Instructions - Page 16
an SD card. Touch to display the "VOICE TX" screen or the "VOICE" (Root) screen, depending on the "VOICE 1st Menu" option in the "Function" Set mode (p. 17-21). SET > Function > VOICE 1st Menu • Push MENU to return to the previous screen. MEMORY KEYER KEY [KEYER] (p. 4-6) (Mode: CW) Touch - Icom IC-7100 | Advanced Instructions - Page 17
(p. 3-10) (Mode: SSB-D/CW/RTTY) Touch to turn the 1⁄4 Tuning function ON or OFF. • " " is displayed when the 1⁄4 Tuning function is ON. CALL RECORD KEY [CD] (p. 9-7) (Mode: DV) Touch to display the "RX HISTORY" screen. • The call record channel appears. (RX01 to RX20) • Push MENU to return to - Icom IC-7100 | Advanced Instructions - Page 18
] (p. 15-2) This function requires to insert an SD card. Touch to display the "VOICE TX" screen or the "VOICE" (Root) screen, depending on the "VOICE 1st Menu" option in the "Function" Set mode (p. 17-21). SET > Function > VOICE 1st Menu • Push MENU to return to the previous screen. CALL SIGN - Icom IC-7100 | Advanced Instructions - Page 19
or SM-50. • A microphone connector is also available on the Main unit. DO NOT simultaneously connect two microphones. r MAIN UNIT CONNECTOR [MAIN UNIT] Connects to the Main unit using with the supplied OPC-2253 Control cable. • The OPC-2253 Control cable is 3.5 meter (11.5 feet) long. DO NOT - Icom IC-7100 | Advanced Instructions - Page 20
view 1 PANEL DESCRIPTION Main unit - Front panel q w q COOLING FAN This is a cooling fan for heat dissipation. Depending on the internal temperature, it rotates at a Low, Mid or High speed. w SD CARD SLOT [SD CARD] Insert an SD card of up to 32 GB SDHC. See Section 13 for details. 1-16 - Icom IC-7100 | Advanced Instructions - Page 21
➥ Connect a PC, using the optional CT-17 ci-v level converter, for external control of the transceiver. ➥ Use for the transceive function with another Icom CI-V transceiver or receiver. When the transceive function is set to ON, changing the frequency, operating mode and so on, on the IC-7100 - Icom IC-7100 | Advanced Instructions - Page 22
• USB cable (supplied with the transceiver) • PC software (such as the optional RS-BA1 or CS- 7100) NEVER connect the transceiver to a PC until the USB driver installation has been completed. About the modulation input: Select "USB" in the "Connectors" Set mode item "DATA OFF MOD" or "DATA MOD - Icom IC-7100 | Advanced Instructions - Page 23
transceiver outputs a low signal to control Output voltage (Low): Current flow: Less than 0.1 V Maximum 200 mA external equipment. BDT Data line for the optional AT-180. --- NC *3 If the modification is performed, (BAND*3) band voltage output. (p. 19-11) Output voltage: --- 0 to 8 V ALC - Icom IC-7100 | Advanced Instructions - Page 24
input SQL SW When the HM-151 is not connected; Squelch switch SPECIFICATIONS Maximum 10 mA UP: Ground DN: Ground through 470 ˘ - - - - - - Open: 'Low' level Close: 'High' level *1 Y ou can change this setting in "MIC AF Out" of the "Function" Set mode. (p. 17-22) SET > Function > MIC AF Out 1-20 - Icom IC-7100 | Advanced Instructions - Page 25
Microphone DDHM-198 (Supplied) w ON q e OFF q PTT SWITCH Hold down to transmit, release to receive. w UP/DOWN KEYS [UP]/[DN] ➥➥Push either key to change the operating frequency, memory channel, Set mode setting, and so on. (pp. 3-9, 4-11, 11-3) ➥➥Hold down either key for 1 second to start - Icom IC-7100 | Advanced Instructions - Page 26
switch (w) is ON. q w t BOTTOM VIEW y M IC GAIN VOLUME [MIC GAIN] Rotate to adjust the microphone output level. • Use this control as an addition to the microphone gain setting of the connected transceiver. Rotating the control too far clockwise may result in an output level that is too high - Icom IC-7100 | Advanced Instructions - Page 27
t SPCH /LOCK TUNER /CALL XFC V/M MW F-1 F-2 1.8 3.5 1 2 7 3 MODE 10 14 18 Set mode (p. 17-20). SET > Function > Lock Function w PTT SWITCH [PTT] (p. 3-23) Hold down to transmit, release to receive band. • Icom's triple band stacking register memorizes 3 frequencies in each band - Icom IC-7100 | Advanced Instructions - Page 28
the RX monitoring mode. (p. 17-13) !3 TUNER/CALL KEY [TUNER/CALL] ❍ ANTENNA TUNER KEY Operation (p. 16-4) (Frequency band: HF, 50/70* MHz) ➥ Push to turn an optional antenna tuner ON or OFF (bypass). ➥ Hold down for 1 second to manually start the antenna tuner. • If the tuner cannot - Icom IC-7100 | Advanced Instructions - Page 29
accessories to the controller 2-6 Required Connections to a Transceiver 2-7 The External Units Connections to a Transceiver 2-8 Power Supply Connections 2-9 DDConnecting the PS-126 power supply 2-9 DDBattery connections 2-9 DDConnecting a non-Icom DC power supply 2-9 Linear Amplifier - Icom IC-7100 | Advanced Instructions - Page 30
electric pipe, since the connection could cause an explosion or electric shock. Controller bottom view DDInstalling the transceiver in a vehicle Controller DC power cable Controller Controller Main unit Controller cable Battery (12V) The following optional devices can be installed, as shown to - Icom IC-7100 | Advanced Instructions - Page 31
, an antenna tuner is useful to match the transceiver and antenna. Low SWR allows full power for transmitting. The IC-7100 has an SWR meter to continuously monitor the antenna SWR. Antenna connection Connect the cable from your HF, 50/70 MHz antenna to the [ANT 1] connector. Connect the cable from - Icom IC-7100 | Advanced Instructions - Page 32
radiation and cause mechanical trouble. Controller Using Ferrite EMI filter* Depending on the installed condition of the transceiver, malfunction may occur by the wraparound of the electric wave. This problem can be resolved by using the Ferrite EMI filter. *The filter connection is required for - Icom IC-7100 | Advanced Instructions - Page 33
Previous view 2 INSTALLATION AND CONNECTIONS Installing the Controller The controller can be installed on the dashboard of a vehicle or console by using the optional Controller bracket. • Controller installtion procedures 1. Place the controller bracket on a dashboard or console. Place the MBF-1 - Icom IC-7100 | Advanced Instructions - Page 34
. This could damage the transceiver. The HM-151 is designed to use with the IC-7000/ IC-7100 series ONLY. OPC-589 HM-36 SM-50 • External Keypad Control the CW memory keyer transmission from the exter- nal keypad by connecting the control circuit to the MIC connector. Set the "Keyer" item in - Icom IC-7100 | Advanced Instructions - Page 35
view 2 INSTALLATION AND CONNECTIONS Required Connections to a Transceiver [ANT2] 144/430MHz BANDS CONNECTOR (p. 2-3) [ANT1] HF, 50/70 MHz BANDS CONNECTOR (P. 2-3) Connect a 50 Ω antenna for the 144/430 MHz frequency bands or 74.8 MHz and above. IC-7100 Connect a 50 Ω antenna for the HF, 50/70 - Icom IC-7100 | Advanced Instructions - Page 36
Set mode (p. 17-24), the receiving tone can normally be output from the [ACC] socket, and the [USB] port can output an IF signal (12 kHz). This is required for the Software-Defined Radio (SDR) operation. The Digital Radio Mondiale (DRM) broadcast can be received using SDR. CAUTION: DO NOT connect - Icom IC-7100 | Advanced Instructions - Page 37
view 2 INSTALLATION AND CONNECTIONS Power Supply Connections Make sure the [POWER] switch is OFF before connecting the DC power cable. • W e recommend using Icom's optional power supply (PS-126: DC13.8 V/25 A). DDConnecting the PS-126 power supply Use the attached AC cable to connect to AC - Icom IC-7100 | Advanced Instructions - Page 38
2 INSTALLATION AND CONNECTIONS Linear Amplifier Connections DD Connecting the IC-PW1/EURO To connect the Icom IC-PW1/EURO, see the diagram below. For IC-PW1/EURO operation, refer to the amplifier's instruction manual. To an antenna [ANT] ACC cable 7-pin side [ACC-1] [REMOTE] Remote Control - Icom IC-7100 | Advanced Instructions - Page 39
available, depending on the transceiver version. To an antenna Non-Icom Linear amplifier [ANT1]*2 RF OUT RF IN ALC SEND Relay Switching diode ALC (Blue) HSEND (Orange) /VSEND GND IC-7100 ACC 13.8 V (Gray) 13-pin plug with ACC cable RWARNING! *2 When connecting a 144 MHz or 430 MHz band - Icom IC-7100 | Advanced Instructions - Page 40
Power ON 3-2 DDBefore first applying power 3-2 DDTuning ON the power 3-2 Selecting a Function menu 3-3 Selecting VFO/Memory mode 3-4 VFO operation 3-5 DDSelecting VFO A or VFO B 3-5 DDVFO equalization 3-5 Selecting a frequency band 3-6 DDUsing the band stacking registers 3-6 Setting - Icom IC-7100 | Advanced Instructions - Page 41
RIT TUNER/CALL MENU NB NR MIC/RF PWR SPEED/PITCH P.AMP ATT NOTCH DR SET QUICK AUTO TUNE RX�CS SPEECH XFC MPAD DDTuning ON the power Normal Power ON: Push [PWR] (L) to turn ON the transceiver. Power OFF: Hold down [PWR] (L) for 1 second to turn OFF the transceiver. [PWR] Partial Resetting - Icom IC-7100 | Advanced Instructions - Page 42
once or twice to select the "D-1" screen (D-1 menu) or "D-2" screen (D-2 menu). • Functions vary, depending on the operating mode. (p. 1-8 to p. 1-11) Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom - Icom IC-7100 | Advanced Instructions - Page 43
[V/M] Programming 10.12000 MHz/CW into Memory channel A01. Memory mode icon Touching the VFO/Memory mode icon or Memory channel selects the VFO or Memory mode. Touch [V/M] VFO mode icon Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left - Icom IC-7100 | Advanced Instructions - Page 44
in the VFO mode, push MENU (C) one or more times to select the "M-1" screen (M-1 menu). wwTouch [A/B](D) to switch between the VFO A and VFO B. • "VFOA" or "VFOB" appears as each VFO is selected. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller - Icom IC-7100 | Advanced Instructions - Page 45
. See the table below for a list of the available frequency bands and their default frequency and mode settings. Cancel edit Operating mode Example: Touch "21" in the above screen The L, R, C or D in the instructions indicate the part of the controller. L: Left side, R: Right side, C: Center bottom - Icom IC-7100 | Advanced Instructions - Page 46
] Switch" item of the "Function" Set mode, pushing [SPEECH/LOCK] turns OFF the lock function. (see p. 17-20 for details) SET(C) > Function > [SPEECH/LOCK] switch Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center - Icom IC-7100 | Advanced Instructions - Page 47
Previous view 3 BASIC OPERATION Setting frequency (Continued) DDQuick Tuning function The operating frequency can be changed in 'kHz' or 'MHz' steps for quick tuning. Select the desired tuning step in each operating frequency band and mode. q T ouch the kHz digits to select the 'kHz' Quick Tuning - Icom IC-7100 | Advanced Instructions - Page 48
MENU (C) to return to the normal operating screen. rrRepeat steps q to e to select the Quick tuning steps for other modes. Touch the kHz digits in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) Touch the Hz digits for 1 - Icom IC-7100 | Advanced Instructions - Page 49
, touch the item for 1 second to open the Default set window, then select the "Default" to reset to the de- fault setting. rrPush SET(C) to exit the Set mode. The L, R, C or D in the instructions indicate the part of the controller. L: Left side, R: Right side, C: Center bottom D: Display (Touch - Icom IC-7100 | Advanced Instructions - Page 50
digit, touch [ENT](D) to set all uninputted digits to "0." • If desired, touch "CE" to delete entering. • If desired, touch [](D) or push MENU the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) Touch the MHz digits Touch - Icom IC-7100 | Advanced Instructions - Page 51
offset frequency input qqTouch the MHz digits to enter the Band selection dis- play. wwTouch [F-INP](D) to enter the Direct input screen. eeIf the Shift direction is minus, touch "• (-)." • [SPLIT] changes to [-SPLIT], and displays the Minus setting mode. rrTouch the desired number to enter - Icom IC-7100 | Advanced Instructions - Page 52
the programmed range. • If desired, touch the item for 1 second to open the Default set window, then select the "Default" to reset to the de- fault setting. rrPush SET(C) to exit the Set mode. If the "Beep Level" item is set to "0," the Band edge beep does not sound. The beep output level - Icom IC-7100 | Advanced Instructions - Page 53
" option. rrTouch the "User Band Edge" item of the "Function" Set mode. Function > User Band Edge ttFollow the instructions in the next topics to delete, insert, edit, change or reset Band edges. yyAfter you have finished, push SET(C) to exit the Set mode. Push SET Touch "Function" Touch "User - Icom IC-7100 | Advanced Instructions - Page 54
or push MENU (C) to return to the "Function" Set screen. • Editing a new Band edge qqEnter the "User Band Edge" screen. SET(C) > Function > User Band Edge wwTouch touch [ENT] The L, R, C or D in the instructions indicate the part of the controller. L: Left side, R: Right side, C: Center bottom D: - Icom IC-7100 | Advanced Instructions - Page 55
Band Edge" screen. SET(C) > Function > User Band Edge wwTouch any band edges for 1 second. eeTouch "Default." • "Initialize Edges?" is displayed. rrTouch [YES](D). • Resets all band edge frequencies to default settings. • If desired, touch "NO" to cancel resetting. ttTouch [](D) or push MENU - Icom IC-7100 | Advanced Instructions - Page 56
USB CW CW-R RTTY RTTY-R AM* FM WFM (Only RX) DV LSB LSB data USB USB data AM AM data FM FM data * On the 144 MHz or 430 MHz bands, only the RX operation is available in the AM mode. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller - Icom IC-7100 | Advanced Instructions - Page 57
the Audio volume ➥➥Rotate [AF] (L) control clockwise to increase the audio output level, counterclockwise to decrease it. Increases [AF] Decreases Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center - Icom IC-7100 | Advanced Instructions - Page 58
open. Noise squelch (FM/DV modes) Recommended level Maximum RF gain RF gain adjustable range S-meter squelch • When used as an RF gain control (Squelch is fixed open; SSB, CW, RTTY only) ❍ Adjusting RF gain (Receive sensitivity) Normally, [RF/SQL] (L) is set to the 12 o'clock position. Rotate - Icom IC-7100 | Advanced Instructions - Page 59
switch to announce the appropriate mode, when the "MODE SPEECH" item is set to "ON" in the "SPEECH" Set mode. (p. 17-15) SET(C) > SPEECH > MODE SPEECH Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom - Icom IC-7100 | Advanced Instructions - Page 60
(C) to exit the Set mode. DDTuning ON the MODE announcement When this function is ON, the selected operating mode is verbally announced when a mode is selected. qqPush SET(C) to enter the Set mode. wwTouch the "MODE SPEECH" item of the "SPEECH" Set mode. SPEECH > MODE SPEECH • If the specified - Icom IC-7100 | Advanced Instructions - Page 61
power meter, SWR meter, ALC meter or COMP meter. • Po : Displays the relative RF output power. • SWR : Displays the SWR of the antenna at the frequency. • ALC : Displays the ALC meter. RF output power is displayed in % (percent), and it becomes the S-meter in receive. ALC zone When ALC meter is - Icom IC-7100 | Advanced Instructions - Page 62
* 70 MHz band transmission is available, depending on the transceiver version. NOTE: The RF output power settings are independently memorized in the HF, 50, 70, 144 and 430 MHz bands. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side - Icom IC-7100 | Advanced Instructions - Page 63
MIC gain. When the MIC gain is adjusted too high, your transmitted voice may be distorted. rrR elease [PTT] to receive. ttPush MENU (C) to close the display. ❍ In the SSB mode: Touch the TX meter to select the ALC meter. Then, while speaking into the microphone, rotate [M-CH] (L) so that the - Icom IC-7100 | Advanced Instructions - Page 64
Menu screen to return to the previous frequency or Memory channel. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller sounds until the transceiver is operated. desired standby mode. • " " appears when "ON" is selected in step e. • Select the VFO, a - Icom IC-7100 | Advanced Instructions - Page 65
and must adhere to the following: • The USB, USB Data, CW and PSK modes • Maximum of 100 watts ERP (Effective Radiated Power) • 2.8 kHz bandwidth (maximum) It is your responsibility to set all controls so that transmission in this frequency band meets the stringent conditions under which amateur - Icom IC-7100 | Advanced Instructions - Page 66
RECEIVE AND TRANSMIT Operating SSB 4-2 Operating CW 4-3 DDAbout the CW reverse mode 4-4 DDAbout keying speed 4-4 DDAbout CW pitch control 4-4 DDCW sidetone function 4-5 DDCW Auto tune function 4-5 Electronic keyer functions 4-6 DDMemory keyer menu DDRTTY decode log Set mode 4-20 Operating AM - Icom IC-7100 | Advanced Instructions - Page 67
/RF PWR (C) to open the MIC gain/RF power adjustment display. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) "LSB" or "USB" appears TX meter w R otate [M-CH] (L) to adjust - Icom IC-7100 | Advanced Instructions - Page 68
: Full break-in • OFF : No break-in (ACC socket connection for TX is necessary, as shown on page 1-17.) If a microphone is connected, its PTT can be used instead of the external TX switch. yyIf the Semi break-in operation is selected at step t, set the Break-in delay. q W hile the "M-3" menu - Icom IC-7100 | Advanced Instructions - Page 69
item of the "Function" Set mode. (p. 17-21) SET(C) > Function > CW Normal Side BFO Interference Desired signal CW mode (LSB side) BFO Interference Desired signal CW-R mode (USB side) Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side - Icom IC-7100 | Advanced Instructions - Page 70
Level" item of the Keyer Set mode (p. 4-10). DDCW Auto tune function The automatic tuning function automatically tunes the displayed frequency when an off-frequency signal is received. This function is active while in the CW mode is selected. ➥➥Push AUTO TUNE RX�CS (R) to automatically adjust for - Icom IC-7100 | Advanced Instructions - Page 71
instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) DDMemory keyer menu construction [KEYER] • Keyer Send screen (p. 4-7) The screen you want to appear first can be selected in the "KEYER 1st Menu" item of the "Function" Set mode - Icom IC-7100 | Advanced Instructions - Page 72
are sent. • Push [−1](D) to reduce the contest number advances by one before sending the memory keyer contents to a station a second time. ttPush MENU (C) to return to the "KEYER" (Root) screen. For your information When an external keypad is connected to pin 3 and pin 7 of the [MIC] connector - Icom IC-7100 | Advanced Instructions - Page 73
the CW contest number. The number automatically advances by 1. This function is available for only one memory keyer channel at a time. "✱" is used in memory keyer channel M2 by default. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left - Icom IC-7100 | Advanced Instructions - Page 74
set window, then select "Default" to reset to the default setting. uuPush MENU (C) to return to the "KEYER" (Root) screen. The L, R, C or D in the instructions indicate the part of the controller. L: Left side, R: Right side, C: Center bottom D: Display (Touch screen) • Contest number Set mode - Icom IC-7100 | Advanced Instructions - Page 75
Previous view 4 RECEIVE AND TRANSMIT Electronic keyer functions (Continued) DDKeyer Set mode This Set mode is used to set the CW sidetone, memory keyer repeat time, dash weight, paddle specifications, keyer type, and so on. • Setting contents q In the CW mode, push MENU (C) one or more times to - Icom IC-7100 | Advanced Instructions - Page 76
view 4 RECEIVE AND TRANSMIT Electronic keyer functions (Continued) DDKeyer set mode (Continued) Side Tone Level (Default: 50%) Select the CW sidetone output level. • 0 to 100% can be selected. Side Tone Level Limit (Default: ON) Set the CW sidetone level limit. When the [AF] (L) control is - Icom IC-7100 | Advanced Instructions - Page 77
to set the transceiver to the transmit mode, or transmit a SEND signal from your TNC. • The TX/RX indicator lights red. • T he Po meter displays the transmitted RTTY signal strength. yyUse your connected PC or TNC (TU) to transmit RTTY (FSK) signals. uuSwitch OFF the external TX switch to receive - Icom IC-7100 | Advanced Instructions - Page 78
are reversed. This reversal can be caused by incorrect TNC connections, setting or commands. To correctly receive reversed RTTY signals, select the RTTY reverse mode. qqOn the Mode selection screen, touch "RTTY" to select the RTTY mode. wwAfter the RTTY mode is selected, touch "RTTY" again on the - Icom IC-7100 | Advanced Instructions - Page 79
to open the De- fault set window, then select the "Default" to reset to the default setting. ttTouch [](D) or push MENU (C) to return to the "M-2" screen (Menu M-2). Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side - Icom IC-7100 | Advanced Instructions - Page 80
reset to the default setting, if desired. yyPush MENU (C) to exit the adjustment mode. The number of the decoder display lines, the UnShift On Space (USOS) function and new line code can be set in the RTTY Set mode. (p. 4-16) The L, R, C or D in the instructions indicate the part of the controller - Icom IC-7100 | Advanced Instructions - Page 81
window, then select the "Default" to reset to the default setting. uuTouch [](D) or push MENU (C) to return to the "KEYER" (Root) screen. iiPush MENU (C) to return to the "M-2" screen (Menu 2). The L, R, C or D in the instructions indicate the part of the controller. L: Left side, R: Right side - Icom IC-7100 | Advanced Instructions - Page 82
RT4], or [RT5] to [RT8](D). • The TX/RX indicator lights red. • The TX contents are displayed beside the " " icon. yyPush MENU (C) to return to the "M-2" screen (Menu M-2). For your information When an external keypad is connected to [MIC] connector on the Controller, one of RT1 to RT4 RTTY memory - Icom IC-7100 | Advanced Instructions - Page 83
• Preprogrammed contents CH Contents RT1 ↵DE ICOM ICOM K↵ RT2 ↵DE ICOM ICOM ICOM K↵ RT3 ↵QSL UR 599-599 BK↵ RT4 ↵QSL DE ICOM ICOM UR 599-599 BK↵ RT5 ↵73 GL SK↵ RT6 ↵CQ CQ CQ DE ICOM ICOM ICOM K↵ RT7 ↵M Y TRANSCEIVER IS IC-7100 & ANTENNA IS A 3-ELEMENT TRIBAND YAGI.↵ RT8 ↵M Y RTTY - Icom IC-7100 | Advanced Instructions - Page 84
RTTY operating record, both TX and RX, into an SD card. Be sure to insert the SD card, otherwise this function does not work properly. The SD card is not supplied by Icom. qqIn the RTTY mode, push MENU (C) one or more times to select the "M-2" screen (M-2 menu). wwTouch [DEC](D) to display the - Icom IC-7100 | Advanced Instructions - Page 85
return to the "RTTY DECODE LOG" screen. ooTouch [](D) or push MENU (C) to return to the RTTY Decoder screen. RTTY decode log Set mode Touch [LOG] Touch "Log Set" File type (Default: Text) Select file type for saving a Log into an SD card, as the Text or HTML format. • Text: Save as a Text - Icom IC-7100 | Advanced Instructions - Page 86
gain/RF power adjustment display. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left MENU (C) to close the display. iiRelease [PTT] to receive. NOTE: On the 144/440 MHz frequency band, you cannot transmit in the AM mode. Convenient Receive - Icom IC-7100 | Advanced Instructions - Page 87
shown below. • If desired, touch [DEF] for 1 second to reset to the default setting. uuPush MENU (C) to exit the "TONE" screen. iiCommunicate in the usual manner. • The tone squelch opens only when you receive a signal containing a matching subaudible tone. • Subaudible tones are superimposed - Icom IC-7100 | Advanced Instructions - Page 88
second to reset to the default setting. uuPush MENU (C) to exit the "TONE" screen. iiCommunicate in the usual manner. • The tone squelch opens only when you receive a signal containing a matching subaudible tone. • Subaudible tones are superimposed on your transmit signal. • Available DTCS codes - Icom IC-7100 | Advanced Instructions - Page 89
detected subaudible tone frequency or DTCS code is set. • If desired, touch [DEF] for 1 second to reset to the default setting. iiTouch [SCAN](D) to cancel the scan. Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom - Icom IC-7100 | Advanced Instructions - Page 90
twice to select the VFO mode. wwSelect the desired frequency band. (p. 3-6) eeOn the Mode selection screen, touch "FM" to select the FM mode. rrRotate the Dial to set the receive frequency (Repeat- er output frequency). When the Auto Repeater function is turned ON (available in only the U.S.A. and - Icom IC-7100 | Advanced Instructions - Page 91
for 1 second to reset to the default setting. ttPush MENU (C) to exit the "TONE" screen. yyCommunicate in the normal way. • Subaudible tones are superimposed on your transmit signal. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side - Icom IC-7100 | Advanced Instructions - Page 92
channel indication once or twice to select the VFO mode. wwSelect the desired frequency band. (p. 3-6) eeOn the Mode selection screen, touch "FM" to select the FM mode. rrRotate the Dial to set the receive frequency (Repeat- er output frequency). ttPush MENU (C) one or more times to display the - Icom IC-7100 | Advanced Instructions - Page 93
can directly receive the other party's transmitted signal. • While holding down XFC (R), the duplex direction and frequency offset are displayed above the function menu. Hold down XFC Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side - Icom IC-7100 | Advanced Instructions - Page 94
"ON" Activates duplex and tone. • "OFF" Auto repeater function is turned OFF. rrPush SET(C) to exit the Set mode. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) 4-29 Push - Icom IC-7100 | Advanced Instructions - Page 95
the set contents into the selected memory channel. "M-1" menu Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) "M-2" menu "M-1" menu 4-30 VFO A Touch [A/B] VFO B Push MENU - Icom IC-7100 | Advanced Instructions - Page 96
function 5-4 Twin PBT operation 5-5 IF filter selection 5-6 DDIF filter selection 5-6 DDFilter passband width setting 5-6 IF (DSP) filter shape 5-7 Noise Blanker 5-8 DDNB Set mode 5-8 Noise Reduction 5-9 Notch function 5-10 DDAuto Notch function 5-10 DDManual Notch function 5-11 Lock - Icom IC-7100 | Advanced Instructions - Page 97
AMP OFF" setting. Preamp 2 is most effective when: • Used on bands above 24 MHz and when signals are weak. • Receive sensitivity is insufficient when using low- gain antennas, or while using a narrow band antenna. (such as small loop, a Beverage antenna or a short Yagi antenna) DDAttenuator The - Icom IC-7100 | Advanced Instructions - Page 98
Gain Control) controls receiver gain to produce a constant audio output level, even when the received signal strength greatly varies. The transceiver has 3 pre-set AGC time constants: fast, mid and slow for SSB, CW, RTTY and AM modes. In the FM , WFM and DV modes, the AGC time constant is fixed as - Icom IC-7100 | Advanced Instructions - Page 99
for off-frequency operation of the received station. The function shifts the receive frequency up to ±9.99 kHz in 10 Hz steps*, without changing the transmit frequency. *The [M-CH] (L) control tunes in 1 Hz steps when the operating frequency readout is set to the 1 Hz step readout. qqPush - Icom IC-7100 | Advanced Instructions - Page 100
Previous view 5 FUNCTIONS FOR RECEIVE Twin PBT operation (Mode: SSB/CW/RTTY/AM) To reject interference, PBT (Passband Tuning) electronically narrows the IF passband width by shifting the IF frequency slightly outside of the IF filter passband. The IC-7100 uses DSP for the PBT function. Moving both - Icom IC-7100 | Advanced Instructions - Page 101
D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) When FILTER2 or FILTER3 is selected in the FM mode, the TX modulation changes to the narrow mode (2.5 kHz). DDFilter passband width setting (Mode: SSB/CW/RTTY/AM) qq - Icom IC-7100 | Advanced Instructions - Page 102
SSB or CW mode. (p. 3-17) wwTouch the Filter icon for 1 second to display the "FILTER" screen. eePush [SHARP] or [SOFT](D) to select either the soft or sharp filter shape. rrPush MENU (C) to exit the "FILTER" screen. Left Display Center Right The L, R, C or D in the instructions indicate the - Icom IC-7100 | Advanced Instructions - Page 103
RECEIVE Noise Blanker (Mode: SSB/CW instructions indicate the part of the controller. L: Left side, R: Right side, C: Center bottom D: Display (Touch screen) NB NB icon DDNB Set mode to reset to the default setting. rrPush NB (C) to return to the previous screen. 1. NB Level (Default: 50%) Set - Icom IC-7100 | Advanced Instructions - Page 104
. The received signals are converted to digital signals and instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) NR NR icon Noise reduction OFF Noise components Noise reduction ON Desired signal (CW) Touch for 1 second to reset - Icom IC-7100 | Advanced Instructions - Page 105
5 FUNCTIONS FOR RECEIVE Notch function (Mode = Auto notch: SSB/AM/FM Manual notch:SSB/CW/RTTY/AM) This transceiver has Auto and Manual Notch functions. ➥➥In the SSB or AM mode, push NOTCH (C) to toggle the Notch function between auto, manual and OFF. • Either the Auto or Manual notch function - Icom IC-7100 | Advanced Instructions - Page 106
Previous view 5 FUNCTIONS FOR RECEIVE Notch function (Continued) DDManual Notch function (Mode =Manual notch:SSB/CW/RTTY/AM) The Manual Notch function allows you to manually attenuate a frequency via the "NOTCH control." qqPush NOTCH (C) once or twice to turn ON the Manual Notch function. • "MN" - Icom IC-7100 | Advanced Instructions - Page 107
Previous view 5 FUNCTIONS FOR RECEIVE Lock function The IC-7100 has two kinds of lock functions; Dial Lock and Panel Lock. The Dial Lock function locks only the Dial, and Panel Lock function locks controller operation. The Dial Lock function prevents frequency changes by accidental movement of the - Icom IC-7100 | Advanced Instructions - Page 108
to ON by default, the peak level of a received signal strength or the output power is displayed for approximately 0.5 seconds. The function can be turned OFF in the "Meter Peak Hold" item of the "Display" Set mode. (p. 17-27) qqPush SET(C) to enter the Set mode. wwTouch the "Meter Peak Hold" item - Icom IC-7100 | Advanced Instructions - Page 109
is equal to the selected sweep step. The band scope measures receive signal location and strength over a specified range on either side of a selected frequency, in either the VFO or memory modes. qqRotate the Dial to select a frequency. wwPush MENU (C) one or more times to select the "M-3" screen - Icom IC-7100 | Advanced Instructions - Page 110
Split function 6-11 DDSplit frequency offset setting 6-12 Measuring SWR 6-13 DDSpot measurement 6-13 DDPlot measurement 6-14 DDSWR Graph Set mode 6-16 DTMF Memory encoder 6-17 DDProgramming a DTMF code 6-17 DDTransmitting DTMF code 6-18 DDTransmitting DTMF code (Direct Input 6-19 DDSetting - Icom IC-7100 | Advanced Instructions - Page 111
switches the transceiver between transmit and receive with your voice. This function provides hands-free operation. DDUsing the VOX function qqSelect the desired frequency band. (p. 3-6) wwOn the Mode selection screen, select either the SSB, AM, FM or DV mode. (p. 3-17) eePush MENU (C) one or - Icom IC-7100 | Advanced Instructions - Page 112
CW mode to automatically toggle the transceiver between transmit and receive when keying. The IC-7100 is capable of Full Break-in or Semi Break-in. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller to reset to the default setting. uuPush MENU (C) to - Icom IC-7100 | Advanced Instructions - Page 113
in function (Continued) DDFull Break-in operation During Full Break-in operation, the transceiver transmits when you key down, then immediately returns to receive when you release. qqOn the Mode selection screen, select the CW or CW-R mode. (p. 3-17) wwPush MENU (C) one or more times to select the - Icom IC-7100 | Advanced Instructions - Page 114
output power, improving signal strength and readability. qqSelect the desired frequency band. (p. 3-6) wwOn the Mode selection screen, select the USB or LSB mode reset to the default setting. When the COMP meter peaks above the COMP level zone, your transmitted voice may be distorted. iiPush MENU - Icom IC-7100 | Advanced Instructions - Page 115
" items of the "Tone Control" Set mode. (p. 17-23) SET(C) > Tone Control > TX > SSB > TBW (WIDE), TBW (MID), TBW (NAR) - WIDE: 100 Hz to 2900 Hz - MID: 300 Hz to 2700 Hz - NAR: 500 Hz to 2500 Hz Left Display Center Right The L, R, C or D in the instructions indicate the part of - Icom IC-7100 | Advanced Instructions - Page 116
CW side tone functions regardless of the "Monitor" setting. qqPush SET(C) to enter the Set mode. wwTouch the "Monitor" item of the "Function" Set mode to open the Default set window, then select "Default" to reset to the default setting. yyPush SET(C) to exit the Set mode. Monitor ON/OFF Monitor - Icom IC-7100 | Advanced Instructions - Page 117
• While holding down XFC (R), you can change the frequency band and operating mode in VFO B. • While holding down XFC (R), the transceiver receives the transmit frequency in VFO B. (2) Touch [A/B](D) to select VFO B, rotate the Dial to set the transmit frequency to 21.310 MHz, and then select - Icom IC-7100 | Advanced Instructions - Page 118
can directly be entered. qqTouch the MHz digits to enter the Band selection display. wwTouch [F-INP](D) to enter the Direct input screen. eeIf the Shift direction is minus, touch "• (-)." • [SPLIT] changes to [-SPLIT], and displays the Minus setting mode. rrTouch the desired number to enter the - Icom IC-7100 | Advanced Instructions - Page 119
select the page. eeTouch the option to turn ON the function. rrPush SET(C) to exit the Set mode. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) While transmitting with both - Icom IC-7100 | Advanced Instructions - Page 120
receive (VFO A) frequency. rrWhile holding down XFC (R), rotate the Dial to set the frequency offset between transmit and receive. • When XFC (R) is released, the receive frequency is displayed. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller - Icom IC-7100 | Advanced Instructions - Page 121
shift, and then touch [ENT](D). • -9.999 to +9.999 MHz can be set in 1 kHz steps. rrPush SET(C) to exit the Set mode. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) Push - Icom IC-7100 | Advanced Instructions - Page 122
in the 144 MHz or 430 MHz bands. Depending on the length of the connected coaxial cable, or installation condition, the measurement may be different from the actual SWR of the antenna in these band. RTTY mode icon w R otate [BANK] (L) to adjust the RF power. e P ush MENU (C) to close the display - Icom IC-7100 | Advanced Instructions - Page 123
measurement allows you to measure the SWR over an entire band. Shows starting measurement SWR measuring step Frequency display mark step Set the "Measuring Step" item of the "SWR GRAPH SET" screen. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. - Icom IC-7100 | Advanced Instructions - Page 124
than 20 W. • If your are operating in the 430 MHz band, adjust the RF power to more than 15 W. • If your are operating in the 70 MHz band, adjust the RF power to more than 20 W. (70 MHz band transmission is available, depending on the transceiver version.) q P ush MIC/RF PWR (C) to open the MIC - Icom IC-7100 | Advanced Instructions - Page 125
the "Default" to reset to the default setting. yyTouch [](D) or push MENU (C) to return to the "SWR" (SWR Graph) screen. uuPush MENU (C) to return to the "M-3" screen (Menu 3). Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side - Icom IC-7100 | Advanced Instructions - Page 126
for storage of often-used DTMF codes sequence of up to 24 digits. DDProgramming a DTMF code qqSelect the desired frequency band. (p. 3-6) wwOn the Mode selection screen, select the FM or DV mode. (p. 3-17) • The DTMF encoder can be used in the FM or DV mode. eePush MENU (C) one or more times to - Icom IC-7100 | Advanced Instructions - Page 127
, touch [SEND], [EDIT] or [SET](D) or push MENU (C), SET (C) or XFC (R), cancels the transmission. • After transmitting, transceiver returns to the "DTMF" screen. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side - Icom IC-7100 | Advanced Instructions - Page 128
, touch [SEND], [EDIT] or [SET](D) or push MENU (C), SET (C) or XFC (R), cancels the transmission. • After transmitting, transceiver returns to the "DTMF" screen. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side - Icom IC-7100 | Advanced Instructions - Page 129
" to reset to the default setting. uuTouch [](D) or push MENU (C) to return to the "DTMF" screen. Example: Set the DTMF transfer speed to 300 milliseconds. Touch [DTMF] Touch [SET] Touch the item Touch the option Example: 300 ms Left Display Center Right The L, R, C or D in the instructions - Icom IC-7100 | Advanced Instructions - Page 130
the setting examples, the Japanese repeater node (port) letters are dif- ferent from those in other countries. Be sure to add a repeater node letter as the 8th digit in the call sign field after a repeater call sign according to the repeater frequency band shown below. 1200 MHz: A (B in Japan) 430 - Icom IC-7100 | Advanced Instructions - Page 131
programming Before starting D-STAR, the following steps are needed. IMPORTANT! STEP 1 Entering your call sign (MY) into the transceiver SET(C) to enter the Set mode. wwTouch the "MY Call Sign" item of the "My Station" Set mode D in the instructions indicate the part of the controller. L: Left side - Icom IC-7100 | Advanced Instructions - Page 132
screen. Call sign edit screen Move the cursor Delete a character Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) Enter "JA3YUA" into [MY1]. q e q Touch "JKL" to enter - Icom IC-7100 | Advanced Instructions - Page 133
"MY" (Your own call sign) programming 2. Enter the Call Sign (Continued) ooTouch the entered call sign to set the call sign to be used. !0 P ush SET(C) to exit the Set mode. ✓✓ Convenient! If necessary, enter a note of up to 4 characters, such as the model of the transceiver, name, area name, and - Icom IC-7100 | Advanced Instructions - Page 134
, JARL envisioned a system of repeaters grouped together into Zones. • The D-STAR repeater enables you to call a HAM station on another repeater through the internet. • The transceiver can be operated in the digital voice mode, including low-speed data operation, for both transmit and receive. 7-5 - Icom IC-7100 | Advanced Instructions - Page 135
for D-STAR repeater operation. In this mode, you can select a preprogrammed repeater or frequency in "FROM" (the access repeater or simplex), and UR call sign in "TO" (destination), as shown to the right. Destination (Repeater/Station) NOTE: If the repeater, set to "FROM" (Access Repeater) has no - Icom IC-7100 | Advanced Instructions - Page 136
view 7 D-STAR INTRODUCTION Communication Form in the DR mode In the DR mode, the transceiver has three communication forms, as shown below. • Local area NOTE: • Programming the repeater list is required for DR mode operation. (pp. 9-29 to 9-37) • Before operating in the DV mode, be sure to - Icom IC-7100 | Advanced Instructions - Page 137
in the setting examples, the Japanese repeater node (port) letters are dif- ferent from other country's. Be sure to add a repeater node letter as the 8th digit in the call sign field after a repeater call sign, according to the repeater frequency band, as shown below. 1200 MHz:A (B in Japan) 430 - Icom IC-7100 | Advanced Instructions - Page 138
Japan" yyTouch your access repeater. • Example: "Hirano" • The transceiver returns to the DR mode screen, and the selected repeater is set in "FROM." 2. Set transceiver returns to the DR mode screen, and "CQCQCQ" is set in "TO." 3. Hold down [PTT] to transmit • While holding down [PTT], the TX/RX - Icom IC-7100 | Advanced Instructions - Page 139
access repeater. • Example: "Hirano" • The transceiver returns to the DR mode screen, and the selected repeater is set in "FROM." "FROM" is selected. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom - Icom IC-7100 | Advanced Instructions - Page 140
repeater is listed. • Example: "11: Japan" !1 Touch the destination repeater. • Example: "Hamacho" • The transceiver returns to the DR mode screen, and the selected repeater is set in "TO." 3. Hold down [PTT] to transmit • While holding down [PTT], the TX/RX indicator lights red. "TO" is selected - Icom IC-7100 | Advanced Instructions - Page 141
Previous view 8 D-STAR OPERATION D-STAR Operating procedures (Continued) < Communication example for a Gateway call> INTERNET JA3YUA calling to JP1YIU port A through JP3YHH port B. JA3YUA, this is JM1ZLK. Hello, how are you? • • • JM1ZLK, this is JA3YUA. Thanks for the nice QSO and I hope - Icom IC-7100 | Advanced Instructions - Page 142
"RX" is displayed when: • The repeater call sign programming is mode through the internet, some packets may be lost due to network error, or the caller's signal is weak getting into the repeater. In such a case, "L" is displayed to indicate that Packet Loss has occurred. When the transceiver receives - Icom IC-7100 | Advanced Instructions - Page 143
station call sign is an- nounced if the RX>CS Speech function is set to ON in the "SPEECH" Set mode. SET (C) > SPEECH > RX>CS SPEECH • If you want to select another call sign in the RX history, rotate [DIAL] while holding down AUTO TUNE RX�CS (R). NOTE: When a received signal is weak, or during DR - Icom IC-7100 | Advanced Instructions - Page 144
own and the repeater's location. The nearest repeaters in your transceiver's repeater list are displayed as the available choices. While DR mode scanning • When the "FROM" data is stored in the TX History. Setting from the TX History (p. 8-13) Select a repeater that you have accessed before, from - Icom IC-7100 | Advanced Instructions - Page 145
the repeater area or name. (Example: "Hirano") • The transceiver returns to the DR mode screen, and the selected repeater is set in "FROM." Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display - Icom IC-7100 | Advanced Instructions - Page 146
not receive the transceiver's signal, because the repeater's output power is higher than the transceiver's. The DR mode scan also scans simplex frequencies if they are entered in the repeater list. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller - Icom IC-7100 | Advanced Instructions - Page 147
as the available choices. To receive your own position, connect an external NMEA format compatible receiver to the transceiver according to the instructions. (See page 10-2 for connecting the third party GPS receiver) If you set your position into the "Manual" item of the "GPS Set" Set mode, and if - Icom IC-7100 | Advanced Instructions - Page 148
transceiver returns to the DR mode screen, and the selected repeater is set in the instructions indicate the part of the controller. L: receive your own position data. • If no repeater is found in a 160 kilometers range, screen 1, as shown to the right, will be displayed. • If the last received - Icom IC-7100 | Advanced Instructions - Page 149
"TX HISTORY" screen appears. ttTouch the repeater to use as your access repeater. • Example: "Hirano" • The transceiver returns to the DR mode screen, and the selected repeater is set in "FROM." Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller - Icom IC-7100 | Advanced Instructions - Page 150
specific station "Your Call Sign" setting (p. 8-17) Select the station call sign in the Your Call Sign memory. To select from RX History Setting from RX History (p. 8-18) When you receive you can switch the repeater group. ➥➥While in the DR mode, push QUICK (C), and then touch "Group Select." To - Icom IC-7100 | Advanced Instructions - Page 151
set in "TO." Example: M aking a Local area call by accessing the "Hirano" repeater. qqPush DR (C) to select the DR mode. transceiver returns to the DR mode screen, and "CQCQCQ" is displayed in "TO." Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller - Icom IC-7100 | Advanced Instructions - Page 152
yyTouch the destination repeater. • Example: "Hamacho" • The transceiver returns to the DR mode screen, and "Hamacho" is displayed in "TO." Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display - Icom IC-7100 | Advanced Instructions - Page 153
to the DR mode screen, and "TOM" is displayed in "TO." After selecting a destination, you can select another station preset in your transceiver by rotating the Dial or [M-CH] (L). Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side - Icom IC-7100 | Advanced Instructions - Page 154
Touch "RX History." • The "RX HISTORY" screen appears. ttTouch the destination name or call sign. • Example: "TOM" • The transceiver returns to the DR mode screen, and "TOM" is displayed in "TO." Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller - Icom IC-7100 | Advanced Instructions - Page 155
. ttTouch "TX History." • The "TX HISTORY" screen appears. yyTouch the destination name or call sign. • Example: "Dallas" • The transceiver returns to the DR mode screen, and "Dal- las" is displayed in "TO." The L, R, C or D in the instructions indicate the part of the controller. L: Left side - Icom IC-7100 | Advanced Instructions - Page 156
transceiver returns to the DR mode screen, and "JM- 1ZLK" is displayed in "TO." • After programming, programmed call sign remains on the DIRECT IN- PUT (UR) screen, until inputting a new call sign. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller - Icom IC-7100 | Advanced Instructions - Page 157
Program a call sign, and touch [ENT]. "K5TIT B" is set in "TO." The following settings are also correct. The repeater node* is input. "/" is input. In this case, the call sign is of a repeater for a Gateway call. *Although the repeater node letter is 'B' for 430 MHz band, 'A' is used in Japan - Icom IC-7100 | Advanced Instructions - Page 158
in Japan) Message operation 9-2 DD TX message programming 9-2 DD Message Transmission 9-5 DD TX message deleting 9-6 Received call sign viewing 9-7 DD View in the RX History screen 9-7 BK mode communication 9-9 EMR communication 9-10 DD Adjusting the EMR AF level 9-11 Display type setting - Icom IC-7100 | Advanced Instructions - Page 159
view 9 D-STAR OPERATION Message operation The transceiver has a total of 5 message memories to store short messages to transmit during DV mode operation. TX messages of up to 20 characters can be programmed in each of the 5 message memories. DDTX message programming 1. Display the TX - Icom IC-7100 | Advanced Instructions - Page 160
Previous view 9 D-STAR OPERATION Message operation (Continued) 2. Enter mode Move the cursor Move the cursor Delete a character Open an input mode window Enter Cancel edit Input a space Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller - Icom IC-7100 | Advanced Instructions - Page 161
D-STAR OPERATION Message operation 2. Enter the TX message (Continued) ooTouch the entered TX message to set the message to be used. !0 Push SET(C) to exit the Set mode. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side - Icom IC-7100 | Advanced Instructions - Page 162
on the LCD. To not display and scroll the received message, turn OFF the RX message display function in "RX Message Display" of the Set mode. (p. 17-27) SET(C) > Display > RX Message Display The received message is displayed and scrolled here. 9-5 Touch "TX Message" Touch "1:JAPAN > TOM" Push - Icom IC-7100 | Advanced Instructions - Page 163
. (Example: 1:) rrTouch the "Clear" item. • The confirmation screen "Clear?" appears. ttTouch [YES](D). yyPush SET(C) to exit the Set mode. Example: T o delete the programmed TX message "JAPAN >TOM" from message memory number 1. Touch "My Station" Touch "TX Message" Touch the message memory for - Icom IC-7100 | Advanced Instructions - Page 164
Push SET(C) to exit the screen. The L, R, C or D in the instructions indicate the part of the controller. L: Left side, R: Right side, C: Center bottom D: Display (Touch screen) RX history number Touch [CD] Touch the screen. Touch [√] Touch [√] Touch [√] When the received call includes the GPS - Icom IC-7100 | Advanced Instructions - Page 165
Push QUICK (C) on the RX HISTORY or the contents screen, then push [∫] or [√](D) to select "Delete" or "Delete All." When the received call includes GPS position data. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side - Icom IC-7100 | Advanced Instructions - Page 166
page. rrT ouch "ON." ttPush SET(C) to exit the Set mode. • "BK" appears. yyWhen both stations are in standby, push [PTT] on the microphone or switch ON the external TX switch to transmit. • The TX/RX indicator lights red. • "BK" blinks on the station that receives the break-in call. uuRelease - Icom IC-7100 | Advanced Instructions - Page 167
AF] (L) control level, whichever is higher. !1 R elease [PTT] or Switch OFF the external TX switch to receive. !2 To cancel the EMR mode, select "OFF" in step i, as described above, or turn OFF the power. Example: T o transmit from the "Hamacho" repeater in the EMR mode Touch "DV Set" Touch "EMR - Icom IC-7100 | Advanced Instructions - Page 168
more times to adjust the EMR audio output level between 0 (minimum) and 100 (maximum) in single digit steps. (Default: 50) rrPush SET(C) to exit the Set mode. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center - Icom IC-7100 | Advanced Instructions - Page 169
." • T he display size changes to the same size such as the repeater name set in "TO" and "FROM." Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) Touch "Display Type" Touch - Icom IC-7100 | Advanced Instructions - Page 170
the page. eeT ouch "ON." rrPush SET(C) to exit the Set mode. • W hen an FM signal is received in the DV mode, the "DV" and "FM" icons sequentially blink, and the transceiver receives the signal in the FM mode. When digital call sign squelch (DSQL) or digital code squelch (CSQL) is selected, the - Icom IC-7100 | Advanced Instructions - Page 171
> DV Auto Reply Touch "DV Set" Touch "Auto Reply" Touch "ON" Push SET Appears After receiving a call from "JG3LUK," the transceiver automatically sends a reply call. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side - Icom IC-7100 | Advanced Instructions - Page 172
the call with your voice. NOTE: Be sure to insert an SD card to the [SD] slot of the transceiver before starting to record a voice announcement. qqPush SET(C) to enter the Set mode. wwTouch the "DV Auto Reply" item of the "Voice Memo" Set mode. Voice Memo > DV Auto Reply • If the specified item is - Icom IC-7100 | Advanced Instructions - Page 173
or the RX message • T he distination station must be set the GPS Auto TX setting (DV-G or DV-A) and the Auto Position reply setting Transceiver can display the Distance and direction when the "GPS Select" item in the "GPS" Set mode is set to "External GPS" and the transceiver received position - Icom IC-7100 | Advanced Instructions - Page 174
software. DDConnection Connect the transceiver to your PC using the USB cable or the OPC-1529R cable, as illustrated below. IC-7100(Rear panel) To a [RS-232C] port To a To the PC [USB] [DATA1] jack port OPC-1529R （Option） Supplied USB cable To a [USB] port Before starting low - Icom IC-7100 | Advanced Instructions - Page 175
in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) Touch "SPEECH" Touch "RX Call Sign SPEECH" Touch "ON (Kerchunk)" or "ON (All)" Example: ON (All) Push SET • When "ON (Kerchunk)" is selected 'JM1ZLK' • T he IC-7100 has - Icom IC-7100 | Advanced Instructions - Page 176
Speech function (Continued) DDTo announce the RX>CS call sign The station call sign that is selected from the RX History by holding down AUTO TUNE RX�CS (R), will be announced. qqPush SET(C) to enter the Set mode. wwTouch the "RX>CS SPEECH" item of the "SPEECH" Set mode. SPEECH > RX>CS - Icom IC-7100 | Advanced Instructions - Page 177
D-STAR OPERATION Speech function (Continued) DDSpeech Language selection The speech language can be set to English or Japanese. This setting is used for all Speech functions. qqPush SET(C) to enter the Set mode. wwTouch the "SPEECH Language" item of the "SPEECH" Set mode. SPEECH > SPEECH - Icom IC-7100 | Advanced Instructions - Page 178
maximum) in single digit steps. (Default: 50%) rrPush SET(C) to exit the Set mode. • W hen "0" (minimum) is selected, the call sign won't be announced. • T he volume level can be adjusted with the [AF] (L) control. Left Display Center Right The L, R, C or D in the instructions indicate the part - Icom IC-7100 | Advanced Instructions - Page 179
in the low-speed data communication mode, the digital squelch opens even if receiving a signal is not addressed to your own call sign. DDThe digital code squelch setting qqPush DR (C) to enter the DR mode. wwPush MENU (C) to select the "D-2" screen (D-2 menu). • T o use the digital code squelch - Icom IC-7100 | Advanced Instructions - Page 180
function in another mode, push MENU (C) to select the "M-2" screen (M-2 menu). eeTouch [DSQL](D) for 1 second to display the "DSQL" screen. rrRotate the Dial to adjust the digital code. • If desired, touch [DEF](D) for 1 second to reset to the default setting. • W hen the received signal's code - Icom IC-7100 | Advanced Instructions - Page 181
(C) to enter the DR mode. wwPush MENU (C) to select the "D-1" screen (D-1 menu). • T o use the Call sign setting in another mode, push MENU (C) to select the "M-2" screen (M-2 menu). • T he CALL SIGN screen can be displayed in the DR, VFO, Memory or Call channel modes. eeTouch [CS](D). • "CALL - Icom IC-7100 | Advanced Instructions - Page 182
(Example: ICOM 01) • T he selected call sign is displayed in the "CALL SIGN" screen. uuPush MENU (C) to exit the "CALL SIGN" screen. iiIf you want to memorizes this setting, touch [MW](D) for 1 second in the "M-1" screen (M-1 menu). Example: W hen changing "UR:" in the 438.03 MHz, DV mode Touch - Icom IC-7100 | Advanced Instructions - Page 183
mode. *Before starting to set the call sign, set the frequency of your access repeater or duplex setting. (See Section 3.) 1. Call sign "R1" setting qqSelect any other than DR mode. (Example: Memory mode) wwPush MENU C or D in the instructions indicate the part of the controller. L: Left side R: - Icom IC-7100 | Advanced Instructions - Page 184
ADVANCED> Changing the Call sign setting (Continued) 2. Gateway "R2" setting oo T ouch "R2:." • T he "RPT2 SELECT" screen is displayed. !0 Touch "GW." • T he display returns to the "CALL SIGN" screen. • W hen you manually Push MENU (C) to exit the "CALL SIGN" screen. • W hen you manually - Icom IC-7100 | Advanced Instructions - Page 185
the repeater list is preloaded into your transceiver. However, if the CPU clears all programmed contents (All Reset), the repeater list is also cleared. We recommend that memory data be backed up externally or be saved to a PC using the optional CS-7100 cloning software. About the repeater list: The - Icom IC-7100 | Advanced Instructions - Page 186
This item MUST be blank. - - ✔ ✔ This item MUST be set to "OFF." - - - - - DDNew repeater programming 1. Repeater group selection qqPush SET(C) to enter the Set mode. wwTouch the "Repeater List" item of the "DV Memory" Set mode. DV Memory > Repeater List • If the specified item is not displayed - Icom IC-7100 | Advanced Instructions - Page 187
OPERATION Repeater list programming (Continued) 2. Repeater name programming yyTouch "NAME" to enter the repeater name edit mode. • input mode window Enter Cancel edit Input a space Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. - Icom IC-7100 | Advanced Instructions - Page 188
Repeater list programming (Continued) 3. Repeater sub name programming !1 Touch "SUB NAME" to enter the repeater sub name edit mode. input mode window Enter Cancel edit Input a space Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. - Icom IC-7100 | Advanced Instructions - Page 189
Be sure to add a repeater node (port) letter as the 8th digit in the call sign field after a repeater call sign, according to the repeater frequency band, as shown below. Note that Japanese repeater node letters are different. 1200 MHz:A (B in Japan) 430 MHz: B (A in Japan) 144 MHz: C (no D-STAR - Icom IC-7100 | Advanced Instructions - Page 190
Previous view 9 D-STAR OPERATION Repeater list programming (Continued) 5. Gateway repeater call sign programming The 8th digit in the call sign, programmed in '4. Repeater call sign programming' as described above, is automatically set to "G" as the gateway port. And you can skip this - Icom IC-7100 | Advanced Instructions - Page 191
Previous view 9 D-STAR OPERATION Repeater list programming (Continued) 7. Access repeater setting The programmed repeaters can be used as an access repeaters in the DR mode. For simplex operation, or when the programmed repeater is not used as an access repeater, select "NO." In this case - Icom IC-7100 | Advanced Instructions - Page 192
offset for 1 second to open the Function set window, and then touch the "Frequency Clear" to delete the frequency. #9 After entering, touch [ENT](D). Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom - Icom IC-7100 | Advanced Instructions - Page 193
view 9 D-STAR OPERATION Repeater list programming (Continued) 11. Position data accuracy level setting When the Repeater Search move the cursor forwards. • T ouch [E/W](D) to toggle between E and W modes. $7 After entering, touch [ENT](D). 9-36 Touch "POSITION" Example: "Approximate - Icom IC-7100 | Advanced Instructions - Page 194
MENU (C) to display "Cancel edit?." Touch [YES](D) to cancel programming and the display returns the RPT LIST screen. Touch "UTC OFFSET" Touch [+]/[-] Touch [] Touch "" * Touch [YES] Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller - Icom IC-7100 | Advanced Instructions - Page 195
Previous view 9 D-STAR OPERATION Editing a repeater list This function reprograms a repeater's data. This is useful when already-programmed data is incorrect, has changed or some data should be added to the list. qqPush SET(C) to enter the Set mode. wwTouch the "Repeater List" item of - Icom IC-7100 | Advanced Instructions - Page 196
Previous view 9 D-STAR OPERATION Deleting a repeater list The programmed repeater contents can be deleted from the repeater list. qqPush SET(C) to enter the Set mode. wwTouch the "Repeater List" item of the "DV Memory" Set mode. DV Memory > Repeater List • If the specified item is not - Icom IC-7100 | Advanced Instructions - Page 197
STAR OPERATION Rearrange the display order of the repeater You can move the programmed repeaters to rearrange their display order in the selected repeater group. The programmed repeater cannot be moved out of their assigned repeater group. qqPush SET(C) to enter the Set mode. wwTouch - Icom IC-7100 | Advanced Instructions - Page 198
view 9 D-STAR OPERATION Adding the Repeater information using the RX History This section describes how to add a new repeater information to the repeater list using the RX history. qqPush DR (C) to enter the DR mode. wwTouch [CD](D). • T he "RX HISTORY" screen are displayed. ee - Icom IC-7100 | Advanced Instructions - Page 199
Previous view 9 D-STAR OPERATION Skip setting for the DR mode scan You can set unnecessary repeaters as scan skip targets. The selected repeaters are skipped during scanning for faster selection and scanning. You can set the skip setting to all repeaters in the selected repeater group, or - Icom IC-7100 | Advanced Instructions - Page 200
Previous view 9 D-STAR OPERATION Repeater group name programming qqPush SET(C) to enter the Set mode. wwTouch the "Repeater List" item of the "DV Memory" Set mode. DV Memory > Repeater List • If the specified item is not displayed, touch [∫] or [√](D) one or more times to select the - Icom IC-7100 | Advanced Instructions - Page 201
view 9 D-STAR OPERATION Repeater detail screen According to the programmed contents, such as position D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) While in the DR mode, and if you set the repeater as - Icom IC-7100 | Advanced Instructions - Page 202
Your call signs can be programmed. qqPush SET(C) to enter the Set mode. wwTouch the "Your Call Sign" item of the "DV Memory" Set mode. DV Memory > Your mode window Enter Cancel edit Input a space Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller - Icom IC-7100 | Advanced Instructions - Page 203
OPERATION Your (destination) call sign programming (Continued) !0 Touch "CALL SIGN" to enter the your call sign edit mode. SET(C) to exit the Set mode. To cancel the programmed data: To cancel the programmed data, push MENU (C) to display "Cancel edit?." Touch "YES" to cancel programming - Icom IC-7100 | Advanced Instructions - Page 204
Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) 9-47 Touch the list for 1 second. Touch "Edit." Touch "." Touch "YES." "TOM/7100 JM1ZLK" is programmed into the Your Call Sign memory - Icom IC-7100 | Advanced Instructions - Page 205
call sign you want to move. qqPush SET(C) to enter the Set mode. wwTouch the "Your Call Sign" item of the "DV Memory" Set mode. DV Memory > Your Call Sign • Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: - Icom IC-7100 | Advanced Instructions - Page 206
Previous view 9 D-STAR OPERATION Deleting Your (destination) call sign The Your (destination) call signs can be deleted from the Your Call Sign memory. qqPush SET(C) to enter the Set mode. wwTouch the "Your Call Sign" item of the "DV Memory" Set mode. DV Memory > Your Call Sign • If the - Icom IC-7100 | Advanced Instructions - Page 207
9 D-STAR OPERATION Your setting is correct? If you make a Local Area call with the Gateway call setting, the destination repeater, repeater as their Access repeater cannot access it, as shown below. BE SURE to set CQCQCQ in "TO" when you intend to make a local call, or after you finish - Icom IC-7100 | Advanced Instructions - Page 208
your own or received position data 10-5 Checking GPS information (Sky view screen 10-6 Adding or editing GPS memory 10-7 DDGPS memory 10-7 DDAdd a GPS memory 10-7 DDGPS group name programming 10-11 DDClearing a GPS data 10-12 DDMoving a GPS data 10-13 DDGPS alarm setting 10-14 Transmitting - Icom IC-7100 | Advanced Instructions - Page 209
own GPS data in all operating modes. You can also transmit GPS data when in the DV mode. To receive GPS data, connect a third-party GPS receiver that has an RS-232C output and NMEA data format. DD GPS receive setting The L, R, C or D in the instructions indicate the part of the controller. L: Left - Icom IC-7100 | Advanced Instructions - Page 210
"GPS Position." eeTouching D) allows you change between my (MY) screen, the received (RX) screen, the GPS memory (MEM) channel screen, and the GPS "Manual" is selected, speed, compass heading and direction do not appear. (p. 10-2) GPS > GPS Set > GPS Select rrPush SET(C) to exit the "GPS POSITION - Icom IC-7100 | Advanced Instructions - Page 211
radio station. Field PM75TS Square Subsquare DDChanging the Compass Direction You can change the compass direction between Heading Up, North Up and South Up. qqWhile displaying the MY, RX Up South Up MEM ALM • The grid locator map of Japan 140° PN QN - Icom IC-7100 | Advanced Instructions - Page 212
of the station you received it from. The GPS Memory is capable of from, select RX eePush QUICK (C). rrTouch "Add To GPS Memory." • "GPS Memory Edit" SET(C) to exit the "GPS Position" screen. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller - Icom IC-7100 | Advanced Instructions - Page 213
screen) This screen is used to receive GPS satellite information when the GPS indicator does not stop blinking for a long time. GPS Information displays the quantity, signal power and position of the GPS satellites. The sky view screen shows the position of GPS satellites. The screen also shows the - Icom IC-7100 | Advanced Instructions - Page 214
(Continued on the next page) ICOM Head Office Tokyo Osaka Group names are just example. Touch "GPS". Touch "GPS Memory" Touch "(No Group)" Push QUICK (C). Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. Touch "Add." L: Left side R: Right - Icom IC-7100 | Advanced Instructions - Page 215
hen the programming is completed, touch [](D) to return to the "GPS MEMORY EDIT" screen. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) 10-8 Example; "Icom 01" is entered - Icom IC-7100 | Advanced Instructions - Page 216
:" to enter the longitude programming mode. @3 Enter the desired longitude using the touch screen. • From 0˚00.00' to 180˚00.00' can be programmed. • If "ddd° mm' ss"" is selected in "Position Format" screen, between 0˚00'00" to 180˚00'00" are programmable. GPS > GPS Set > Position Format @4 Touch - Icom IC-7100 | Advanced Instructions - Page 217
touch [YES](D) to write the programmed GPS memory. • If a previously added GPS memory is edited, select "." • T he data is added to the GPS memory, and then displays its data screen. To cancel the programming data: To cancel the programmed data, push SET(C) to display the "Cancel - Icom IC-7100 | Advanced Instructions - Page 218
GPS/GPS-A OPERATION Adding or editing GPS memory (Continued) DDGPS group name programming You can register the name of each GPS group. qqPush SET(C) to enter the Set mode. wwTouch the "GPS MEMORY" item of the "GPS" Set mode. GPS > GPS in the instructions indicate the part of the controller. L: - Icom IC-7100 | Advanced Instructions - Page 219
two ways to clear the memories; • Erasing all GPS memory in a group. • Erasing a specific memory channel. Example: Erasing all in the "(No Group)." qqPush SET(C) to enter the Set mode. wwTouch the "GPS MEMORY" item of the "GPS" Set mode. GPS > GPS Memory • If the specified item is not displayed - Icom IC-7100 | Advanced Instructions - Page 220
programmed GPS memories to rearrange their display order in the selected GPS memory group. In order to move the GPS memory out of their assigned memory group, edit and move, and then save. qqPush SET(C) to enter the Set mode. wwTouch the "GPS MEMORY" item of the "GPS" Set mode. GPS > GPS Memory - Icom IC-7100 | Advanced Instructions - Page 221
is selected, the alarm sounds depend on the "Alarm Area (Group)" setting in the Set mode. GPS > GPS Alarm > Alarm Area (Group) GPS beeping screen Blinks The pop up is displayed and 3 beeps sound. Alarm area 2 (Setting specific station) When a specified memory is selected: Extended range (approx - Icom IC-7100 | Advanced Instructions - Page 222
sounds depending on the "Alarm Area (RX/Memory)" setting in the Set mode. GPS > GPS Alarm > Alarm Area (RX/Memory) • Even if "RX" is selected in step r, and the received signal has no position, the GPS alarm does not sound. Touch "RX." "RX" is displayed. GPS beeping screen Blinks The pop up is - Icom IC-7100 | Advanced Instructions - Page 223
step t to set the GPS sentence. • A maximum of 4 GPS sentences can be set at a time. uuPush SET(C) to exit the Set mode. NOTE: • Set the GSV sentence to OFF when sending the GPS message to conventional digital transceivers (IC-2820H, IC-E2820, ID-800H, IC-91AD, IC-E91, IC-V82, IC-U82, IC-2200H, ID - Icom IC-7100 | Advanced Instructions - Page 224
(space included). !0 Touch [ENT](D) when the programming is completed. • Returns to the "GPS Message" screen. !1 Push SET(C) to exit the Set mode. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom - Icom IC-7100 | Advanced Instructions - Page 225
mode supported with the D-PRS to transmit position data. In GPS-A operation, the following codes are transmitted to the PC connected to the IC-7100. GPS-A code is based on APRS® code. (APRS® : Automatic Packet Reporting System). Left Display Center Right The L, R, C or D in the instructions - Icom IC-7100 | Advanced Instructions - Page 226
you transmit with the altitude setting ON, to those products that are not capable of displaying the altitude (IC9100, IC-80AD, IC-E80D, ID-880H, ID-E880, IC-92AD, ICE92D), the characters appear as a comment. (Continued on the next page) 10-19 Touch "GPS TX Mode." Touch "GPS-A(DV-A)." Touch "Unproto - Icom IC-7100 | Advanced Instructions - Page 227
ouch a symbol for 1 second to select the [Direct Input] mode, and other symbols are also selectable. 7. Setting SSID To assist in identifying a station's type, the displayed APRS® (Automatic Packet Reporting System) based SSID is added after the GPS-A data call sign. The way to add SSID's differs - Icom IC-7100 | Advanced Instructions - Page 228
input mode. • programming is com- pleted. • Returns to the "Comment" screen. @4 Touch [](D) to return to the previous screen. DDDisplaying your position using a mapping software If you transmit to an I-GATE station, then enter the call sign information on the internet map website, the set GPS - Icom IC-7100 | Advanced Instructions - Page 229
R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) DDSetting the GPS automatic transmission qqPush SET(C) to enter the Set mode. wwTouch the "GPS Auto TX" item of the "GPS" Set mode. GPS > GPS Auto TX • If the - Icom IC-7100 | Advanced Instructions - Page 230
Selecting a Memory channel 11-3 DDSelecting in the VFO mode 11-3 DDSelecting in the Memory mode 11-3 Selecting a Call channel 11-4 Programming a Memory channel 11-5 DDProgramming in the VFO mode 11-5 DDProgramming in the Memory mode 11-5 DDProgramming the Call channels 11-5 DDProgramming in - Icom IC-7100 | Advanced Instructions - Page 231
or during repairs. Therefore, we recommend that you backup the memory content or save it to an SD card or to a PC. • T he SD card is not available from Icom. Purchase an SD card to meet your needs. • T he optional CS-7100 cloning software can also be used to backup your memory data. 11-2 - Icom IC-7100 | Advanced Instructions - Page 232
be selected. • "BLANK" appears when no information has been programmed into the Memory channel. (Blank channel) • Y ou can instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) Outer: [BANK] Inner: [M-CH] While in the VFO mode - Icom IC-7100 | Advanced Instructions - Page 233
Factory default frequencies and operating modes are programmed into the Call channels. Change these to suit your operating needs. qqSelect the 144 or 430 MHz frequency band. (p. 3-6) wwPush TUNER/CALL (L) to select the Call channel of the selected frequency band. • "CALL1" appears. • Rotate [M-CH - Icom IC-7100 | Advanced Instructions - Page 234
The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) [Example]: Programming 7.088 MHz/LSB into Memory channel 12 while in the VFO mode. [Example]: Programming 21.280 MHz/USB into Memory channel 18 while in - Icom IC-7100 | Advanced Instructions - Page 235
The Memory channel contents, programmed in the DR mode, can also be copied to the VFO. (p. 11-9) The L, R, C or D in the instructions indicate the part of the controller. L: Left side, R: Right side, C: Center bottom D: Display (Touch screen) DR Set the desired contents. MENU [BANK]/ [M-CH] Blinks - Icom IC-7100 | Advanced Instructions - Page 236
on any band screen. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) "MEMORY LIST" screen of Bank A. DDChecking the Memory contents programmed in the DR mode qqPush - Icom IC-7100 | Advanced Instructions - Page 237
to select the "M3" screen (Menu 3). rrTouch [MEMO](D). ttTouch [M-CL](D) for 1 second to clear the contents. • T he programmed contents disappear. • "BLANK" appears. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side - Icom IC-7100 | Advanced Instructions - Page 238
Memory channel contents into the selected VFO. • "BLANK" appears if the selected Memory channel is a blank channel. In this case nothing can be copied. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom - Icom IC-7100 | Advanced Instructions - Page 239
]: Programming a MENU (C) one or more times to select the "M- 3" screen (Menu 3). ttTouch [MEMO](D) to display the "MEMO" screen (Memory Menu mode selection window. • Touch "" to input a space. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller - Icom IC-7100 | Advanced Instructions - Page 240
touch [](D) to move the cursor forwards. !0 Repeat steps i and o to program up to 16 characters memory name, and then touch [ENT](D) to save the to the "MEMO" (Memory) screen. • Push MENU (C) to return to the "M-3" screen (Menu 3). After programming, touch [ENT] Touch [] to return to the "MEMO - Icom IC-7100 | Advanced Instructions - Page 241
Selecting a Memory display type While in the memory mode, the programmed memory name can be displayed. qqTouch the Memory channel number indication once or twice to select the Memory mode. (p. 3-4) wwPush QUICK (D) to open the Quick Menu window. eeTouch [Name Display]. rrTouch the desired Display - Icom IC-7100 | Advanced Instructions - Page 242
content cannot be written. Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) Operating frequency of the VFO or Memory mode MPAD Memo pads Newest In this example, 21.347.24 MHz - Icom IC-7100 | Advanced Instructions - Page 243
up, starting from the most recently written. Operating frequency of the VFO or Memory mode MPAD When you call up a Memo pad, the previously displayed content is automatically stored in a temporary pad. The temporary pad can be recalled by pushing MPAD (R) one or more times. • Y ou may think - Icom IC-7100 | Advanced Instructions - Page 244
view Section 12 SCAN OPERATION Scan types 12-2 Preparation 12-3 Scan Set mode 12-4 Voice Squelch Control function 12-6 Scan edge programming 12-7 Programmed scan (VFO mode 12-8 Fine programmed scan (VFO mode 12-9 Memory scan (Memory mode 12-10 DDMemory scan 12-10 DDMode Select scan 12-11 - Icom IC-7100 | Advanced Instructions - Page 245
. The IC-7100 has several scan types; Programmed scan, Memory scan, Select Memory scan, Mode Select scan and ∂F (Delta Frequency) scan. Rotating the Dial changes the scanning direction as the default. The Dial functions during a scan can be set in the Scan Set mode. (p. 12-5) PROGRAMMED SCAN - Icom IC-7100 | Advanced Instructions - Page 246
12-5) • Scan speed The scan speed can be set to fast or slow in the Scan Set mode. (p. 12-5) • Dial function How the Dial functions during a scan, can be set in the Scan Set mode. (p. 12-5) • Squelch status ❍ The scan starts with the squelch open For a programmed scan: When the tuning step is 1 kHz - Icom IC-7100 | Advanced Instructions - Page 247
. • P ush QUICK (C), and then touch "Default" to reset to the default setting, if desired. yyPush MENU (C) to return to the "SCAN" screen. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display - Icom IC-7100 | Advanced Instructions - Page 248
Set mode (Continued) SCAN Speed (Default: Fast) Select the desired scan speed between slow and fast. • Slow: The scan is slower. • Fast: The scan is faster. SCAN Resume (Default: ON) Set received, the scan pauses according to this setting. When the "SCAN Resume" is set to "OFF," this setting - Icom IC-7100 | Advanced Instructions - Page 249
resumes if the received signal includes no modes (SSB, AM and FM). • T he VSC function resumes the scan on unmodulated signals, regardless of whether the Scan Resume function is set to ON or OFF. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller - Icom IC-7100 | Advanced Instructions - Page 250
. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) [M-CH] MENU Touch [MW] for 1 second Programming 14.000.00 MHz/USB into 2A. Programming 14.360.00 MHz/USB into 2B. 12-7 - Icom IC-7100 | Advanced Instructions - Page 251
for scan edge programming. If the same frequencies are programmed into the Program Scan Edge channels, the programmed scan will not start. qqTouch the Memory channel number indication once or twice to select the VFO mode. (p. 3-4) wwTouch the mode icon to display the Mode selection screen, and - Icom IC-7100 | Advanced Instructions - Page 252
Previous view 12 SCAN OPERATION Fine programmed scan (VFO mode) When a signal is received during a Fine programmed scan, the scanning tuning step is temporarily set to 10 Hz and the scan speed decreases. Left Display qqStart the programmed scan. • Follow steps q through u as described on page 12 - Icom IC-7100 | Advanced Instructions - Page 253
as the "MAIN DIAL (SCAN)" option in the Scan Set mode, rotating the Dial changes the scanning direction. (p. 12-4) ttTouch [MEMO](D) to cancel the scan. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom - Icom IC-7100 | Advanced Instructions - Page 254
Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) Touch [MEMO] for 1 second Touch "MODE-SEL." Touch the mode icon, and then touch the desired operating mode While Mode Select scanning 12-11 - Icom IC-7100 | Advanced Instructions - Page 255
as the "MAIN DIAL (SCAN)" option in the Scan Set mode, rotating the Dial changes the scanning direction. (p. 12-4) eePush [MEMO](D) to cancel the scan. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom - Icom IC-7100 | Advanced Instructions - Page 256
for 1 second displays "SELECT ALL Clear?." Touch [YES](D) to clear all Select Memory channel settings. Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) Appears "SCAN" screen When the - Icom IC-7100 | Advanced Instructions - Page 257
C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) Touch [SCAN] Touch [SPAN] one or more times to select the ∂F span width. Rotate the Dial (VFO mode) Rotate the [M-CH] (Memory mode) Set the center frequency While - Icom IC-7100 | Advanced Instructions - Page 258
(VFO mode/Memory mode) (Continued) DDAbout the Fine ∂F scan When a signal is received during a Fine ∂F scan, the scanning tuning step is temporarily set to . Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: - Icom IC-7100 | Advanced Instructions - Page 259
or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) Select the VFO mode The receive frequency and the operating mode setting NOTE: When the VFO mode is selected, you can normally operate the transceiver; the operating - Icom IC-7100 | Advanced Instructions - Page 260
Menu window. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) When the VFO frequency is set as the priority channel The receive frequency and the operating mode setting - Icom IC-7100 | Advanced Instructions - Page 261
scanning and so on. To start the DR mode scan, touch [SCAN] in the "D-1" screen. When a signal is received on the priority channel The Priority channel is automatically selected, and PRIO blinks on the screen. • T he scan pause timer and resume settings are the same as for a normal scan. Priority - Icom IC-7100 | Advanced Instructions - Page 262
Section 13 USING AN SD CARD About the SD card 13-2 Saving data onto the SD card 13-3 Inserting the SD card 13-4 DDFormatting the SD card 13-4 Removing the SD card 13-5 DDRemoving the SD card while the transceiver's power is ON..13-5 Saving the setting data onto an SD card 13-6 Saving with - Icom IC-7100 | Advanced Instructions - Page 263
Previous view 13 USING AN SD CARD About the SD card The SD and SDHC cards are not available from Icom. Purchase locally. An SD card of up to 2 GB or an SDHC of up to 32 GB, can be used with the IC-7100. Icom has checked the compatibility with the following SD and SDHC cards. (As of June 2013) - Icom IC-7100 | Advanced Instructions - Page 264
data onto the SD card The following data can be stored onto the card: • Data settings of the transceiver Memory channel contents, and repeater lists stored in the transceiver. • Communication contents The transmitted and received audio. • Communication log The communication and receive history log - Icom IC-7100 | Advanced Instructions - Page 265
data. Before formatting any programmed card, make a backup file onto your PC. qqTurn OFF the transceiver, and then insert the card into the slot. wwTurn ON the transceiver. • " " appears when the SD card is inserted. eePush SET(C) to enter the Set mode. rrTouch the "SD Card" Set mode. • If the - Icom IC-7100 | Advanced Instructions - Page 266
DDRemoving the SD card while the transceiver's power is ON qqPush SET(C) to enter the Set mode. wwTouch the "SD Card" Set mode. • If SD card until a click sounds, and then carefully pull it out. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller - Icom IC-7100 | Advanced Instructions - Page 267
13 USING AN SD CARD Saving the setting data onto an SD card Memory channels, Set mode item settings, and repeater lists can be saved on the SD card. Saving data settings on the SD card allows you to easily restore the transceiver to its previous settings, even if an All reset is performed. Left - Icom IC-7100 | Advanced Instructions - Page 268
• W hile saving, a progress bar is displayed, then the "SD CARD" screen is displayed after the save is completed. !0 Push SET(C) to exit the Set mode. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom - Icom IC-7100 | Advanced Instructions - Page 269
IC-7100 and then operating with the same data. Saving the current data is recommended before loading other data in the transceiver. (Example: L oading all the data in the "Set20130301_01" file) qqPush SET(C) to enter the Set mode. wwTouch the "Load Setting" item of the "SD Card" Set mode. (SD Card - Icom IC-7100 | Advanced Instructions - Page 270
, settings data loading begins. • W hile loading, "LOADING" and a progress bar are displayed. iiAfter loading ends, "COMPLETED!" appears. To complete the loading, reboot the transceiver. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left - Icom IC-7100 | Advanced Instructions - Page 271
the SD card. DDAbout the SD card's folder contents The folder in the SD card contains the following: qqIC-7100 folder The folders created in the IC-7100 are contained in this IC-7100 folder. wwDecode folder The RTTY decode folder is created. eeRTTY folder The transmitted or received RTTY decode - Icom IC-7100 | Advanced Instructions - Page 272
a backup file on your PC Windows 7 is used for these instructions. qqInsert the SD card into the SD card drive on your PC. • If no SD card drive is built-in, connect a memory card reader (purchase locally) and then insert the SD card into it. wwClick the "Open folder to view files" option - Icom IC-7100 | Advanced Instructions - Page 273
that you format all SD cards to be used with the IC-7100, even preformatted SD cards for PCs or other uses. See page 13-4 and 13-5 for details of inserting and removing the SD card. IC-7100 Cloning software(Rev. MM) and manuals 2013/6/MM PC Transceiver SD card to the Card reader 3. Copying the - Icom IC-7100 | Advanced Instructions - Page 274
the current data is recommended before loading other data into the transceiver. 5. Updating the repeater list u Push SET(C) to enter the Set mode. i Touch the "Load Setting" item of the "SD Card" Set mode. (SD Card > Load Setting) • If the specified item is not displayed, touch [∫] or [√](D) one - Icom IC-7100 | Advanced Instructions - Page 275
, settings data loading begins. • W hile loading, "LOADING" and a progress bar are displayed. !4 After loading ends, "COMPLETED!" appears. To complete the loading, reboot the transceiver. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left - Icom IC-7100 | Advanced Instructions - Page 276
The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) 1. Saving the master transceiver's setting data onto the SD card. q Save the master transceiver's setting data onto the SD card, as described on page 13 - Icom IC-7100 | Advanced Instructions - Page 277
14-2 Changing the recording mode 14-3 Playing back the received............14-9 Record the transmit and receive audio into the same file. 14-10 Start to record when the [PTT] switch is pushed 14-11 Viewing the folder information 14-12 Viewing the file information 14-13 Viewing the SD card - Icom IC-7100 | Advanced Instructions - Page 278
enables you to record both received and transmitted audio, a QSO with a DX'pedition, and playback the recorded audio after the QSO. NOTE: Be sure to insert an SD card into the transceiver before recording a QSO audio. DDTo start recording qqPush QUICK (C) to open the Quick Menu screen. wwTouch the - Icom IC-7100 | Advanced Instructions - Page 279
recording mode in the Set mode to record only the received audio. The default setting is "TX&RX" (Both transmit and receive signals are recorded). qqPush SET(C) to enter the Set mode. wwTouch the "REC Mode" item of the "Voice Memo" Set mode. (V oice Memo > QSO Recorder > Recorder Set > REC Mode - Icom IC-7100 | Advanced Instructions - Page 280
back the recorded audio qqPush SET(C) to enter the Set mode. wwTouch the "Play Files" item of the "Voice Memo" Set mode. (V oice Memo > QSO starts to playback. ttTouch [](D) or push MENU (C) to stop the playback, and return to the file list screen. SET Touch "Voice Memo." Touch "QSO Recorder." - Icom IC-7100 | Advanced Instructions - Page 281
mode and audio category. • W hen the receive audio is playing back, the audio category is displayed as "RX the total file time, regardless of the skip time setting. Total time Shows the file's total playback time. mode. When the repeater name is programmed in your repeater list, the name is - Icom IC-7100 | Advanced Instructions - Page 282
, and return to the previous screen. rrPush SET(C) to exit the Set mode. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) SET Touch "Voice Memo." Touch "QSO Recorder." 14 - Icom IC-7100 | Advanced Instructions - Page 283
file is deleted. uuPush SET(C) to exit the Set mode. When you want to erase all audio files in the folder at one time, select "Delete All" in step t above. The L, R, C or D in the instructions indicate the part of the controller. L: Left side, R: Right side, C: Center - Icom IC-7100 | Advanced Instructions - Page 284
folder is deleted. yyPush SET(C) to exit the Set mode. When you want to erase all folders at one time, select "Delete All Folders" in step r. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side - Icom IC-7100 | Advanced Instructions - Page 285
if no signals are received. • S quelch Auto: The transceiver records audio only while receiving signals (the squelch opens). rrPush SET(C) to exit the Set mode. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side - Icom IC-7100 | Advanced Instructions - Page 286
and receive audio. (Default setting) • W hen you set the RX REC Condition item to "Squelch Auto," the transceiver records audio to the new file when the squelch either opens or closes. (Voice Memo > QSO Recorder > Recorder set > RX REC Condition) rrPush SET(C) to exit the Set mode. SET - Icom IC-7100 | Advanced Instructions - Page 287
's [PTT] switch is pushed, transmitting using the VOX function or the CI-V remote controller. • All transmit audio is recorded. (W hen "RX Only" is set in the "REC Mode" item, transmit audio is not recorded) • W hen the transceiver receives a signal less than 10 seconds after transmitting, the - Icom IC-7100 | Advanced Instructions - Page 288
ttTouch [](C) to cancel the information screen. • T ouching SET (C) or QUICK (C) also cancels. yyPush SET(C) to exit the Set mode. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch - Icom IC-7100 | Advanced Instructions - Page 289
yyTouch [](C) to cancel the information screen. • T ouching SET (C) or QUICK (C) also cancels. uuPush SET(C) to exit the Set mode. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch - Icom IC-7100 | Advanced Instructions - Page 290
(Continued) Example of file information screens (The display items differ, depending on the recording contents.) • Transmit Information screen (Your own position) (T ransmitting in the DR mode) • Receive Information screen (Your own position) (R eceiving in the DR - Icom IC-7100 | Advanced Instructions - Page 291
(C) also cancels. ttPush SET(C) to exit the Set mode. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) SET Touch "SD Card." Touch "SD Card Info." Shows the information - Icom IC-7100 | Advanced Instructions - Page 292
Connect the memory card reader to the PC, and then insert the SD card into the reader. • If your PC has an SD card drive, insert the card into the drive. wwWhen the SD card is inserted in the SD card drive of the PC or the SD card reader, the screen appears, as shown to the right. • T he [IC-7100 - Icom IC-7100 | Advanced Instructions - Page 293
Previous view Section 15 VOICE TX FUNCTION Recording the voice audio 15-2 Playing back the recorded voice audio 15-3 Programming a memory name 15-4 Transmitting the recorded voice audio 15-6 DDAdjusting the TX volume level 15-7 Voice TX Set mode 15-8 15-1 - Icom IC-7100 | Advanced Instructions - Page 294
in the SSB, AM (HF/50 MHz only), FM or DV mode. The Voice TX function can be assigned to a key on the optional HM-151 remote control mic or an external keypad. (p. 17-22) NOTE: Be sure to insert an SD card into the transceiver before recording a voice audio. qqPush MENU (C) one or more times - Icom IC-7100 | Advanced Instructions - Page 295
to return to the "VOICE TX RECORD" screen. Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) Touch [VOICE] Push MENU Touch [REC] (Example) Touch [T1] While playing Touch [≈] 15-3 - Icom IC-7100 | Advanced Instructions - Page 296
, symbol or number. • T ouch [ [AB] ](D) to open the input mode selection window. • Touch " " to input a space. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) Touch - Icom IC-7100 | Advanced Instructions - Page 297
a memory name (Continued) iiTouch [](D) to move the cursor backwards, or touch [](D) to move the cursor forwards. ooRepeat steps u and i to program up to 16 characters memory name, and then touch [ENT](D) to save the name, and return to the "VOICE TX RECORD" screen. !0 Touch [](D) to - Icom IC-7100 | Advanced Instructions - Page 298
TX continues pausing, if receiving a signal. B ut if the squelch is manually opened, the voice audio is repeatedly transmitted, according to the repeat time setting. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side - Icom IC-7100 | Advanced Instructions - Page 299
[VOICE] Touch [LEVEL] Rotate the Dial to adjust Reset to the Exits the "TX LEVEL" default setting screen. Hiding the Voice TX memory name The voice TX : Displays the "VOICE TX" screen first. rrPush SET(C) to exit the Set mode. "M-2" (Menu 2) screen After touching [VOICE]. When "VOICE-Root" is - Icom IC-7100 | Advanced Instructions - Page 300
below for details of items and options. • Push QUICK (C), and then touch "Default" to reset to the default setting, if desired. uuPush MENU (C) to return to the "VOICE" screen. Repeat Time (Default: 5sec) Set the repeat interval to between 1 and 15 seconds (in 1 second steps) for the voice - Icom IC-7100 | Advanced Instructions - Page 301
Previous view Section 16 ANTENNA TUNER OPERATION Connecting the antenna tuner 16-2 DDConnecting an AH-4 16-2 DDConnecting an -180 16-5 DDBefore operating 16-5 DDOperating 16-6 Setting the AT-180 internal switches 16-7 DDAutomatic tuner start (HF bands only 16-7 DDPTT tune function 16-7 16-1 - Icom IC-7100 | Advanced Instructions - Page 302
OFF the transceiver's power. DDConnecting an AH-4 The optional AH-4 matches the IC-7100 to a long wire antenna more than 7 m/23 ft long (3.5 MHz and above). • See page 16-4 for operation. • See the AH-4 instruction manual installation and an- tenna connection details. IC-7100 To [TUNER] AH - Icom IC-7100 | Advanced Instructions - Page 303
Weight (Approximately) : 1.2 kg; 2.6 lb Supplied accessories : S ee the AH-4 instruction manual DD Specifications for the AT-180 Frequency coverage : 1.8-54 MHz Input impedance : 50 Ω Maximum input power : 120 W Minimum tuning power : 8 W Matching impedance range : 1 6.7-150 Ω (HF band - Icom IC-7100 | Advanced Instructions - Page 304
. • The TX LED lights red. • " " blinks while tuning. • A fter changing the frequency, you should hold down TUNER/CALL (L) for 1 second to manually start tuning. In this case, the CW mode and 10 W output power are au- tomatically selected, and the TX LED lights red. NOTE: DO NOT change the - Icom IC-7100 | Advanced Instructions - Page 305
na. Even if the antenna tuner tune this antenna, it causes to damage the antenna tuner. • NEVER transmit with the tuner ON if no antenna is connected. This will damage both the transceiver and antenna tuner. • Check the untuned antenna SWR. (Less than 3:1 for the HF bands; Less than 2.5:1 for the - Icom IC-7100 | Advanced Instructions - Page 306
. The AT-180's minimum operating input power is 8 W. qqCheck the transceiver's output power is set to 8 W. wwPush TUNER/CALL (L) to turn ON the AT-180. • " " appears. For the HF band: The antenna is automatically tuned during transmit if the antenna SWR is higher than 1.5:1. For the - Icom IC-7100 | Advanced Instructions - Page 307
S2 S1 DC BA DDAutomatic tuner start (HF bands only) If you want to turn ON the tuner when the VSWR is worth than 1.5:1, turn this function ON in the "Auto Start" item of the "Function" Set mode, and turn OFF the Antenna tuner. (p. 17-20) SET(C) > Function > Tuner > Auto Start DDPTT tune function - Icom IC-7100 | Advanced Instructions - Page 308
-2 DDThe Set mode settings 17-2 Set mode items and Default settings 17-3 Voice Memo Set mode 17-11 DV Set mode 17-13 SPEECH Set mode 17-15 QSO/RX Log Set mode 17-16 Function Set mode 17-18 Tone Control Set mode 17-23 Connectors Set mode 17-24 Display Set mode 17-27 Time Set Set mode 17-30 - Icom IC-7100 | Advanced Instructions - Page 309
item. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) DDThe Set mode settings qqPush SET(C) to enter the Set mode. wwIf the specified item is not displayed, touch [∫] or - Icom IC-7100 | Advanced Instructions - Page 310
SET MODE Set mode items and Default settings ➥➥Call sign (Section 9) ➥➥RX History (Section 9) ➥➥MY Station (Section 7) ➥➥GPS (Section 10) ➥➥SD Card (Section 13) NOTE: The default settings shown below in bold are for the USA version. The default settings may differ, depending on your transceiver - Icom IC-7100 | Advanced Instructions - Page 311
the voice synthesizer. QSO/RX Log In this item, set the QSO/RX History Log options. QSO Log*1 OFF or ON Selects whether or not to make a communication log on the SD card. RX History Log*1 OFF or ON Selects whether or not to make a DV mode's re- ceive history log on the SD card. CSV Format - Icom IC-7100 | Advanced Instructions - Page 312
Select the function of the [RF/SQL] control. OFF, 10ms, 15ms, 20ms, 25ms or Sets the transmission's timing of the IC-7100 to 30ms prevent any external equipment that is connected from damage by the transmitted RF. OFF, 10ms, 15ms, 20ms, 25ms or See HF above. 30ms OFF, 10ms, 15ms, 20ms, 25ms - Icom IC-7100 | Advanced Instructions - Page 313
the notch function for the SSB mode. [NOTCH] Switch (AM) SSB/CW Sync Tuning CW Normal Side VOICE 1st Menu KEYER 1st Menu Speaker Out MIC AF Out RC MIC [F-1] [F-2] Mode Select Power OFF (With No Controller) REF Adjust Auto, Manual or Auto/Manual OFF or ON LSB or USB VOICE-Root or VOICE-TX KEYER - Icom IC-7100 | Advanced Instructions - Page 314
the USA version. The default settings may differ, depending on your transceiver version. Tone Control RX SSB RX HPF/LPF RX Bass RX Treble AM RX HPF/LPF RX Bass RX Treble FM RX HPF/LPF RX Bass RX Treble DV RX HPF/LPF WFM CW RX Bass RX Treble RX Bass RX Treble RX HPF/LPF RTTY RX HPF/LPF TX SSB - Icom IC-7100 | Advanced Instructions - Page 315
or closed). AF or IF Sets the [USB] connector and the [ACC] socket usage to received audio output or the IF output for DRM (Digital Radio Mondiale). 0 %~50 %~100 % Sets the audio output level at the [ACC] socket and the [USB] connector. 0 %~50 %~100 % Sets the IF output level at the [ACC - Icom IC-7100 | Advanced Instructions - Page 316
. Selects whether or not to automatically correct the time data by a received GPS sentence. Sets the time difference between UTC (Universal Time Coordinated) and the local time. Sets the clock display mode. Sets to automatically turn OFF the transceiver power after no operation is made during this - Icom IC-7100 | Advanced Instructions - Page 317
Clone Mode Clone Master Mode Touch Screen Calibration Reset Partial Reset All Reset In this item, set other options. Shows the transceiver's firmware version number. Reads or writes the CS-7100 data to or from the PC, and/or receives data from a Master transceiver. Writes your IC-7100 (Master - Icom IC-7100 | Advanced Instructions - Page 318
Previous view 17 SET MODE Voice Memo Set mode Voice Memo > QSO Recorder > Insert an SD card into the transceiver before selecting this item. Touch [] to start voice recording. • "Recording started." appears. • [] is displayed while recording. - Icom IC-7100 | Advanced Instructions - Page 319
an SD card into the transceiver before selecting this item. PTT Auto REC (Default: OFF) Voice Memo > QSO Recorder > Recorder Set > PTT Auto REC (PTT Auto REC) Turn the PTT Automatic Recording function ON or OFF. Recording starts when a signal is transmitted from an external speaker microphone - Icom IC-7100 | Advanced Instructions - Page 320
the SD (up to 10 seconds). If no SD card is port or [DATA1] jack*, the transceiver automatically transmits it. *"USB2 Function" or "DATA1 Function" item must be set to "DV Data." (p. 17-25) Digital Monitor (Default: Auto) DV Set > Digital Monitor (Digital Monitor) Select the receive mode - Icom IC-7100 | Advanced Instructions - Page 321
OFF. The operating mode is fixed to the DV mode. • ON: Automatically selects the FM mode for tempo- rary operation. RX Record (RPT) (Default: ALL) DV Set > RX Record (RPT) (RX Record (RPT)) The transceiver can record the data of up to 50 indi- vidual calls. When the received signal includes - Icom IC-7100 | Advanced Instructions - Page 322
view 17 SET MODE SPEECH Set mode RX Call Sign SPEECH (Default: ON (Kerchunk)) SPEECH > RX Call Sign SPEECH (RX Call Sign SPEECH) Turn the RX call sign speech function ON or OFF for calls received in the DV mode. • OFF: No announcement is made even when a call is received. • ON (Kerchunk - Icom IC-7100 | Advanced Instructions - Page 323
a receive history log. • OFF:The RX History Log function is OFF. • ON : The transceiver makes a DV mode's receive his- tory log on the SD card. The transceiver starts making a receive history log when you finish to talk. NOTE: • T he folder name is automatically created as [IC- 7100\RxLog - Icom IC-7100 | Advanced Instructions - Page 324
) 30.5 Caller's altitude, if sent. (unit: m) Records only when you receive in the DV mode. The RX History log contents are shown below: Content Example Description Frequency 438.010000 RX Frequency Mode DV Operating mode (DV is fixed) Caller JA3YUA A Call sign of the caller station - Icom IC-7100 | Advanced Instructions - Page 325
, you can program a total of 30 band edge frequencies in this item. See page 3-14 for programming details. RF/SQL Control (Default: RF+SQL) Function > RF/SQL Control (RF/SQL Control) Set the [RF/SQL] control operation. • AUTO: [RF/SQL] functions as only an RF gain con- trol in SSB, CW and RTTY - Icom IC-7100 | Advanced Instructions - Page 326
17 SET MODE Function Set mode (Continued) TX Delay (Default: All bands; OFF) Function > TX Delay (TX Delay) Sets the transmission's timing for each operating band. When an external device, such as a vacuum tube linear amplifier or a receiver preamplifier, is connected to the transceiver and - Icom IC-7100 | Advanced Instructions - Page 327
not be turned ON in the DV mode. Auto Start (Default: OFF) Function > Tuner > Auto Start (Tuner (Auto Start)) Turn the Automatic Antenna Tuner function ON or OFF for an external antenna tuner (like the optional AT-180). This function is for only the HF bands. • OFF: Tuning starts only when - Icom IC-7100 | Advanced Instructions - Page 328
CW mode. • KEYER-Root: The Memory keyer menu appears first. • KEYER-SEND: The Keyer SEND menu appears first. Speaker Out (Default: ON) Function > Speaker Out (Speaker Out) Select the speaker output function. • OFF: The speaker does not output the received au- dio. The [ACC] socket, [USB] port - Icom IC-7100 | Advanced Instructions - Page 329
the mode selection with the optional HM-151 remote control mic, to simplify operation. • SSB, CW, RTTY, AM, FM, WFM, DV Power OFF (With No Controller) (Default: ON) Function > Power OFF (With No Controller) (Power OFF (With No Controller)) Select to automatically turn OFF the transceiver when - Icom IC-7100 | Advanced Instructions - Page 330
audio high-pass filter to between 100 Hz and 2000 Hz in 100 Hz steps. RX HPF/LPF (Default Tone Control > RX > (Mode) > RX HPF/LPF (RX HPF/ LPF) (Mode: SSB/CW/RTTY/AM/FM/DV) First select the operating mode, then set the receive audio low-pass filter to between 500 Hz and 2400 Hz in 100 Hz steps - Icom IC-7100 | Advanced Instructions - Page 331
the [AF] control. ACC/USB Output Select (Default: AF) Connectors > ACC/USB Output Select (ACC/USB Output Select) Select whether to use the [USB] connector and the [ACC] socket for a usual received audio, or to use the IF output for [DRM (Digital Radio Mondiale)]. • AF: The received audio is - Icom IC-7100 | Advanced Instructions - Page 332
CI-V Address (CI-V Address) To distinguish equipment, each CI-V transceiver has its own Icom standard address in hexadecimal code. The IC-7100's default address is 88h. When 2 or more IC-7100s are controlled through a PC at the same time, set a different address for each device between 01h and DFh - Icom IC-7100 | Advanced Instructions - Page 333
SET MODE Connectors Set mode (Continued) DV Data/GPS Out Baud (Default: 4800) Connectors > USB2/DATA1 Function > DV Data/GPS Out Baud (DV Data/GPS Out Baud) Set the DV or GPS bands. HSEND is used for the HF/50 MHz bands. 9600bps Mode (Default: OFF) Connectors > 9600bps Mode (9600bps Mode) - Icom IC-7100 | Advanced Instructions - Page 334
displays the peak level of a received signal strength or the output power for approximately 0.5 seconds. BW Popup (PBT) (Default: ON) Display > BW Popup (PBT) (BW Popup (PBT)) Select whether or not to display the PBT shift value while rotating the TWIN-PBT control. • OFF: Turns the function OFF - Icom IC-7100 | Advanced Instructions - Page 335
the opening message at power ON. • OFF: Opening message display is skipped. • ON: Icom logo, MY call sign and the product model ("IC-7100")* are displayed at power ON. Display > System Language (System Language) Set the system language of the transceiver to English or Japanese. • English - Icom IC-7100 | Advanced Instructions - Page 336
Set mode (Continued) Choose your language carefully When the system language of the transceiver is set to Japanese, the IC7100 has the capability to display both English and Japanese characters. HOWEVER, if you select Japanese as the display language (p. 17-28), all menu items throughout the IC-7100 - Icom IC-7100 | Advanced Instructions - Page 337
00 and 23:59. The time is displayed in the 24 hour format. GPS Time correct (Default: Auto) Time Set > GPS Time Correct (GPS Time Correct) Select whether or not the time data is automatically corrected by a received GPS sentence. • OFF: The time data is not automatically corrected. • Auto: The - Icom IC-7100 | Advanced Instructions - Page 338
purchased). Therefore, after the All resetting, you cannot use the transceiver in the DR mode until reprogramming the repeater list. See page 19-4 for details. ✓✓ Recommend! Before the All resetting, we recommend you save the programmed data you purchased onto an SD card. See page 13-6 for details - Icom IC-7100 | Advanced Instructions - Page 339
Previous view Section 18 DATA COMMUNICATION Connections 18-2 DDWhen connecting to [DATA2 18-2 DDWhen connecting to [ACC 18-2 DDWhen connecting to [MIC 18-2 Packet (AFSK) operation 18-3 Setting the data transmission speed 18-4 Adjusting the TNC output level 18-5 DDUsing a level meter or - Icom IC-7100 | Advanced Instructions - Page 340
9 10 11 12 5678 1234 FSKK AF GND SEND* RTTY OUTPUT AUDIO INPUT GND PTT Connect to the serial port, parallel port, speaker jack, microphone jack or line IN/ OUT jack and so on. See the instruction manual of the application for details. *e HF/50 MHz: HSEND u 144/430 MHz: VSEND • When using a TNC - Icom IC-7100 | Advanced Instructions - Page 341
received, the S-meter is displayed ac- cording to the signal strength level. • In the SSB data mode, the ¼ tuning function can be used for critical tuning. (p. 3-10) ttOperate the PC (software) or TNC to transmit. • W hen operating in the SSB data mode, adjust the TNC output level so that the ALC - Icom IC-7100 | Advanced Instructions - Page 342
data transmission at 9600 bps. This is used for only regular audio or slower data transmission. rrPush SET(C) to exit the Set mode. Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) 18-4 - Icom IC-7100 | Advanced Instructions - Page 343
in the Set mode (SET(C) > Connectors > USB2/DATA1 Function), the USB port sends an RTTY decode signal. In this case, you must connect a USB cable* between the transceiver's USB port on the rear panel and the PC. (p. 17-25) *Purchase separately • T he USB driver and the installation guide can be - Icom IC-7100 | Advanced Instructions - Page 344
Resetting the CPU 19-3 DDPartial reset 19-3 DDAll reset 19-4 Data cloning 19-5 DDCloning between transceivers using a mini plug cable..........19-5 DDCloning using a cloning software 19-6 DDInitial setup using an SD card 19-7 Importing the repeater list in a CSV format file 19-8 Programming - Icom IC-7100 | Advanced Instructions - Page 345
the fuses If a fuse blows, and the transceiver stops functioning, find the source of the problem, and repair it. Then replace the damaged fuse with a new, adequately rated fuse. R WARNING! Turn OFF the power and disconnect the DC power cable from the transceiver before performing any work on the - Icom IC-7100 | Advanced Instructions - Page 346
(VFO frequency, VFO settings, menu contents) without clearing the items listed below: • Memory channel contents (Section 4) • Repeater list (p. 9-28) • Call sign memories (p. 9-45) • TX Message data (p. 9-2) • GPS Memory contents (p. 10-7) • GPS Message data (p. 10-17) • Programmed user band edge - Icom IC-7100 | Advanced Instructions - Page 347
save the programmed data onto an SD card, or to your PC using the optional cloning software (CS-7100) before doing an All reset. After the All reset is finished, load or write the saved data into your transceiver. qqPush SET(C) to enter the Set mode. wwTouch the "Reset" item of the "Others" Set mode - Icom IC-7100 | Advanced Instructions - Page 348
of the programmed contents from one IC-7100 to another. You can clone using an SD card, optional cloning software (CS-7100) or a mini plug cable (purchase separately). See page 13-15 for an SD card cloning. DDCloning between transceivers using a mini plug cable qqConnect a mini plug cable to the - Icom IC-7100 | Advanced Instructions - Page 349
you want to write the programmed data into the transceiver using a PC, see the CS-7100 instruction manual for details. qqSave the IC-7100's setting data onto an SD card. (p. 13-6) (SET(C) > SD Card > Save Setting) wwStart-up the Windows that the CS-7100 is installed. eeInsert the SD card in the PC - Icom IC-7100 | Advanced Instructions - Page 350
the [SD] radio button. w Click [Open...] to show the data file selection screen. e Select the "icf" file format stored in a [Setting] folder on the card. r Click [OK] to read the selected file, and open the cloning screen. Set the desired settings in the CS-7100. The initial setup is required - Icom IC-7100 | Advanced Instructions - Page 351
list is read to the CS-7100. • Import is complete. Click Click • See the CS-7100 instruction manual ("' Select the Clone Mode") for details about how to write the imported repeater list to the transceiver. • See page 19-9 for details about how to program or export the repeater list. About - Icom IC-7100 | Advanced Instructions - Page 352
. wwProgram each item of the repeater list, using the CS7100. • See the Help file of the CS-7100 for assistance. 2. Exporting the Repeater list qqSelect the "Repeater List" folder or each repeater group on the tree view screen. wwClick "Export" in the [File] menu, and then click "Group..." or - Icom IC-7100 | Advanced Instructions - Page 353
. "HOT" blinks instead of the TX indicator. When the protector is activated, wait until the power amplifier cools down, using the transceiver in only the stand-by or receive mode. DO NOT turn the transceiver power OFF when the protector is ON. If you do, the cooling fan will not function and it - Icom IC-7100 | Advanced Instructions - Page 354
to ON. • For the TX voice memory, set the "VOICE" item to ON. 1.5kø ±5% S2 2.2kø ±5% S3 4.7kø ±5% S4 USER BOX An external keypad should be purchased separately. External keypad Band voltage modification The transceiver does not output the band voltage from the [ACC] socket by default because - Icom IC-7100 | Advanced Instructions - Page 355
Select an amateur band. Sec. 3 • TX power is set too low. • Push MIC/RF PWR , and then rotate the Sec. 3 [BANK] control clockwise. • The mic gain is set too low. (SSB) • Push MIC/RF PWR , and then rotate the [M- Sec. 3 CH] control clockwise. • T he antenna is bad, or the coaxial cable is - Icom IC-7100 | Advanced Instructions - Page 356
Previous view 19 MAINTENANCE Troubleshooting DDTransmit and receive (Continued) PROBLEM POSSIBLE CAUSE SOLUTION REF. The antenna is not prop- • The antenna SWR is adjusted too high. • Adjust the antenna SWR. Sec. 6 erly tuned. • Check the coaxial cable. • Change the length of the coaxial - Icom IC-7100 | Advanced Instructions - Page 357
repeater list in your radio. • Reload the repeater list using the CS- Sec. 19 the DR mode will not appear. 7100 cloning software on the CD. • Reload the repeater list using an SD card. Sec. 13, 19 • Enter the Repeater list data directly into Sec. 9 the transceiver. Even holding down • T he - Icom IC-7100 | Advanced Instructions - Page 358
Previous view Section 20 CONTROL COMMAND Remote jack (CI-V) information 20-2 DDCI-V connection example 20-2 DDData format 20-2 DDCommand table 20-3 DDData content description 20-11 20-1 - Icom IC-7100 | Advanced Instructions - Page 359
an RS-232C port. The Icom Communications Interface-V (CI-V) controls the transceiver. Up to 4 Icom CI-V transceivers or receivers can be connected to the PC. See page 17-25 for setting the CI-V condition using the set mode. 9−15V DC RS-232C cable PC ct-17 IC-7100 mini-plug cable DDData format - Icom IC-7100 | Advanced Instructions - Page 360
operating mode for transceive see p. 20-12 Read the band edge frequencies see p. 20-11 Read the operating frequency see p. 20-11 Read the operating mode see p. 20-11 Send the operating frequency 00 Select the LSB mode 01 Select the USB mode 02 Select the AM mode 03 Select the CW mode 04 - Icom IC-7100 | Advanced Instructions - Page 361
only) see p. 20-11 Send CW messages*1 Turn OFF the transceiver Turn ON the transceiver*2 *1 In the CW mode, if an external TX switch is ON, or the Break-in function is ON, a message will be transmitted as CW code when you send it from your PC. *2 When sending the power ON command (18 01), the - Icom IC-7100 | Advanced Instructions - Page 362
Send/read the Notch function set- ting for AM mode (00=Auto, 01=Manual, 02=Auto/Manual) 00/01 Send/read the SSB/CW Synchro- nous Tuning function setting (00=OFF, 01=ON) 00/01 Send/read the CW normal side setting (00=LSB, 01=USB) 00/01 Send/read the voice 1st menu (00=VOICE-Root, 01=VOICE - Icom IC-7100 | Advanced Instructions - Page 363
=ON) Send/read the WFM mode selection of the [MODE] key on the HM-151 (00=OFF, 01=ON) Send/read the Power OFF setting when no controller is connected. (00=OFF, 01=ON) Send/read the REF Adjust setting (0000=0%, 0128=50%, 0255=100%) Send/read the RX Call Sign SPEECH setting (00=OFF, 01=ON (Kerchunk - Icom IC-7100 | Advanced Instructions - Page 364
to 02 00/01 00/01 00/01 Description Send/read the "USB2" (COM port) function setting (00=OFF, 01=RTTY Decode, 02=DV Data) Send/read the [DATA1] function setting (00=OFF, 01=RTTY Decode, 02=DV Data, 03=GPS) Send/read the GPS output setting (00=OFF, 01=DATA1USB2) Send/read the DV or - Icom IC-7100 | Advanced Instructions - Page 365
GPS time correction setting (00=OFF, 01=Auto) see p. 20-13 Send/read the UTC offset setting 00/01 Send/read the clock display mode (00=LOCAL, 01=UTC) 00 to 04 Send/read the Auto Power OFF function setting ) Send/read the DTMF Speed setting (00=100 msec., 01=200 msec., 02=300 msec., 03 - Icom IC-7100 | Advanced Instructions - Page 366
RX Record (RPT) setting (00=ALL, 01=Latest Only) Send/read the BK function setting (00=OFF, 01=ON) Send/read the EMR mode setting (00=OFF, 01=ON) Send/read EMR AF Level (0000=0% to 0255=100%) Send/read the external GPS receiver setting (00=OFF, 01=External GPS, 02=Manual) Send/read the GPS Receiver - Icom IC-7100 | Advanced Instructions - Page 367
p. 20-14 Send/read the CSQL code (DV mode) 00 Send/read the Transceiver's status (RX) 01 Send/read the Transceiver's status (TX) 00 Send/read Antenna tuner OFF (through) 01 Send/read Antenna tuner ON 02 Send/read the Manual tuning selec- tion 00 Send/read Transmit frequency monitor - Icom IC-7100 | Advanced Instructions - Page 368
100 kHz digit: 0-9 10 kHz digit: 0-9 10 MHz digit: 0-9 1 MHz digit: 0-9 1000 MHz digit: 0 (Fixed) 100 MHz digit: 0-4 • Operating mode Command: 01, 04, 06 q XX w XX q Operating mode 00: LSB 05: FM 01: USB 06: WFM 02: AM 07: CW-R 03: CW 08: RTTY-R 04: RTTY 17: DV w Filter setting 01: FIL1 - Icom IC-7100 | Advanced Instructions - Page 369
, the codes, such as operating frequency and operating mode*, should be added after the frequency band code and register code, as shown below. *See t to %1 on 'Memory content setting.' (p. 20-16) qqFrequency band code Code Freq. band Frequency range (unit: MHz) 01 1.8 1.800000- 1.999999 02 - Icom IC-7100 | Advanced Instructions - Page 370
view 20 CONTROL COMMAND Remote digit: 0-5 1 min. digit: 0-9 0.1 min. digit: 0-9 0.01 min. digit: 0-9 0.001 min. digit: 0-9 0 (fixed) 1 kHz digit: 0-9 100 Hz digit: 0-9 100 kHz digit: 0-9 10 kHz digit: 0-9 10 MHz digit: 0 (fixed) 1 MHz digit: 0-9 • Unproto Address setting Command: 1A 05 0201 Set - Icom IC-7100 | Advanced Instructions - Page 371
Transmit polarity: 0: Normal 1: Reverse Receive polarity: 0: Normal 1: Reverse 0 (fixed) First digit: 0-7 Second digit: 0-7 Third digit: 0-7 • Digital code squelch setting Command: 1B 07 q XX Second digit: 0-9 First digit: 0-9 • DV MY call sign setting Command: 1F 00 Set your own call sign and - Icom IC-7100 | Advanced Instructions - Page 372
@1-@8 Call sign of the calling station (8 characters; fixed) @9-#2 Note of the calling station (4 characters; fixed) See 'Character code setting.' (p. 20-12) "FF" stands for no message receiving after turning ON the transceiver. • DV RX Status setting Command: 20 0201, 20 0202 Data Bit Status - Icom IC-7100 | Advanced Instructions - Page 373
DTCS code and polarity setting.' (p. 20-14) @4 Digital code squelch setting See '• Digital code squelch setting.' (p. 20-14) @5-@7 Duplex offset frequency setting See '• Duplex Offset frequency setting.' (p. 20-13) @8-#5 Destination call sign setting (8 characters; fixed) #6-$3 R1 (Access repeater - Icom IC-7100 | Advanced Instructions - Page 374
Previous view Section 21 SPECIFICATIONS AND OPTIONS Specifications 21-2 DDGeneral 21-2 DDTransmitter 21-2 DDReceiver 21-3 Options 21-4 21-1 - Icom IC-7100 | Advanced Instructions - Page 375
MHz Output power 2 to 100 W (AM: 1 to 30 W)* 2 to 50 W (AM: 1 to 15 W)* 2 to 50 W 2 to 35 W * In the AM mode, transmission can be performed only on the HF/50/70 MHz frequency band. • Modulation system: SSB: Digital PSN modulation AM: Digital Low power modulation FM: Digital - Icom IC-7100 | Advanced Instructions - Page 376
-50 dB • Spurious and image rejection ratio HF band: More than 70 dB 50/70 MHz bands*: More than 70 dB *except 1/2 IF through on 50/70 MHz bands 144/430 MHz bands*: More than 65 dB *except IF through on 144 MHz band • AF output power: More than 2.0 W at 10% distortion with an - Icom IC-7100 | Advanced Instructions - Page 377
. An optional OPC-599 is required for connection. For remote transceiver control using a personal computer equipped with an RS-232C port. You can change frequencies, operating mode, memory channels, and so on with your computer. External speakers suitable for mobile operation. SP-35: Compact-type - Icom IC-7100 | Advanced Instructions - Page 378
type • CS-7100 cloning software Use this software to program settings, memory channels and set mode contents quickly and easily via your PC's USB port. A USB cable is required. (A-Mini B type, supplied with the transceiver) • RS-BA1 ip remote control software To remotely control radios using the RS - Icom IC-7100 | Advanced Instructions - Page 379
A-7085-2EX-0b © 2013 Icom Inc. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
-
313
-
314
-
315
-
316
-
317
-
318
-
319
-
320
-
321
-
322
-
323
-
324
-
325
-
326
-
327
-
328
-
329
-
330
-
331
-
332
-
333
-
334
-
335
-
336
-
337
-
338
-
339
-
340
-
341
-
342
-
343
-
344
-
345
-
346
-
347
-
348
-
349
-
350
-
351
-
352
-
353
-
354
-
355
-
356
-
357
-
358
-
359
-
360
-
361
-
362
-
363
-
364
-
365
-
366
-
367
-
368
-
369
-
370
-
371
-
372
-
373
-
374
-
375
-
376
-
377
-
378
-
379
 |
 |
ADVANCED INSTRUCTIONS
i7100
20 CONTROL COMMAND
15 VOICE TX FUNCTION
14 VOICE MEMORY FUNCTION
13 USING AN SD CARD
12 SCAN OPERATION
11 MEMORY OPERATION
10 GPS/GPS-A OPERATION
9
D-STAR OPERATION <ADVANCED>
8
D-STAR OPERATION <BASIC>
7
D-STAR INTRODUCTION
6
FUNCTIONS FOR TRANSMIT
5
FUNCTIONS FOR RECEIVE
4
RECEIVE AND TRANSMIT
3
BASIC OPERATION
2
INSTALLATION AND CONNECTIONS
1
PANEL DESCRIPTION
16 ANTENNA TUNER OPERATION
17 SET MODE
18 DATA COMMUNICATION
19 MAINTENANCE
21 SPECIFICATIONS AND OPTIONS
INTRODUCTION
HF/VHF/UHF ALL MODE TRANSCEIVER