Icom IC-7100 Advanced Instructions - Page 361
CONTROL COMMAND, Command table Continued, Sub cmd., Description
View all Icom IC-7100 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 361 highlights
Previous view 20 CONTROL COMMAND Remote jack (CI-V) information DDCommand table (Continued) Cmd. Sub cmd. 14 0E 0F 12 15 16 17 18 19 15 01 02 05 11 12 13 14 15 16 16 02 12 22 40 41 42 43 Data 0000 to 0255 0000 to 0255 0000 to 0255 0000 to 0255 0000 to 0255 0000 to 0255 0000 to 0255 0000 to 0255 00 01 0000 to 0255 00 01 0000 to 0255 0000 to 0255 0000 to 0255 0000 to 0255 0000 to 0255 0000 to 0255 00 01 02 01 02 03 00 01 00 01 00 01 00 01 00 01 Description Send/read the COMP level (0000=0 to 0255=10) Send/read the Break-IN Delay setting (0000=2.0d to 0255=13.0d) Send/read NB level (0000=0% to 0255=100%) Send/read the Monitor gain level (0000=0% to 0255=100%) Send/read the VOX gain level (0000=0% to 0255=100%) Send/read the Anti VOX gain level (0000=0% to 0255=100%) Send/read the LCD contrast level (0000=0% to 0255=100%) Send/read the LCD backlight level (0000=0% to 0255=100%) Read the squelch status (squelch closed) Read the squelch status (squelch open) Read the S-meter level (0000=S0, 0120=S9, 0241=S9+60 dB) Read various SQL function's status (squelch closed) Read various SQL function's status (squelch open) Read the PO meter level (0000=0%, 0143=50%, 213=100%) Read the SWR meter level (0000=SWR1.0, 0048=SWR1.5, 0080=SWR2.0, 0120=SWR3.0) Read the ALC meter level (0000=Min. to 0120=Max.) Read the COMP meter level (0000=0 dB, 0130=15 dB, 0241=30 dB) Read the Vd meter level (0000=0 V, 0013=10 V, 0241=16 V) Read the Id meter level (0000=0, 0097=10, 0146=15, 0241=25) Send/read Preamp OFF Send/read Preamp ON (144/430 MHz) Send/read Preamp 1 ON (HF/50 MHz) Send/read Preamp 2 ON (HF/50 MHz) Send/read AGC FAST Send/read AGC MID Send/read AGC SLOW Send/read Noise Blanker OFF Send/read Noise Blanker ON Send/read Noise Reduction OFF Send/read Noise Reduction ON Send/read Auto Notch function OFF Send/read Auto Notch function ON Send/read Repeater tone OFF Send/read Repeater tone ON Send/read Tone squelch OFF Send/read Tone squelch ON Cmd. 16 17 18 Sub cmd. 44 45 46 47 48 4B 4C 4F 50 56 57 58 5B 00 01 Data Description 00 Send/read Speech compressor OFF 01 Send/read Speech compressor ON 00 Send/read Monitor function OFF 01 Send/read Monitor function ON 00 Send/read VOX function OFF 01 Send/read VOX function ON 00 Send/read BK-IN function OFF 01 Send/read Semi BK-IN function ON 02 Send/read Full BK-IN function ON 00 Send/read Manual notch function OFF 01 Send/read Manual notch function ON 00 Send/read DTCS OFF 01 Send/read DTCS ON 00 Send/read VSC function OFF 01 Send/read VSC function ON 00 Send/read Twin Peak Filter OFF 01 Send/read Twin Peak Filter ON 00 Send/read Dial lock function OFF 01 Send/read Dial lock function ON 00 Send/read DSP filter type SHARP 01 Send/read DSP filter type SOFT 00 Send/read manual notch width WIDE 01 Send/read manual notch width MID 02 Send/read manual notch width NAR 00 Send/read SSB transmit bandwidth WIDE 01 Send/read SSB transmit bandwidth MID 02 Send/read SSB transmit bandwidth NAR 00 Send/read DSQL/CSQL OFF (DV mode only) 01 Send/read DSQL ON (DV mode only) 02 Send/read CSQL ON (DV mode only) see p. 20-11 Send CW messages*1 Turn OFF the transceiver Turn ON the transceiver*2 *1 In the CW mode, if an external TX switch is ON, or the Break-in function is ON, a message will be transmitted as CW code when you send it from your PC. *2 When sending the power ON command (18 01), the command "FE" must be sent before the basic format. • 19200 bps: 25, • 9600 bps: 13, • 4800 bps: 7, • 1200 bps: 3, • 300 bps: 2 Example: When operating with 4800 bps q w e r t u FEF EFE 88EO 1 8 01 F D × 7 q Preamble code (fixed) w Transceiver's default address e Controller's default address r Command number t Sub command number u End of message code (fixed) 20-4