Dell PowerEdge R905 Hardware Owner's Manual (PDF) - Page 39

Remote Access, Expansion Cards

Page 39 highlights

Table 1-8. System Messages (continued) Message Causes Corrective Actions Read fault Requested sector not found The operating system Replace the diskette. cannot read from the hard Ensure that the diskette drive, the system could and hard drive cables are not find a particular properly connected. See sector on the disk, or the "Troubleshooting an requested sector is Optical Drive" on page 158, defective. or "Troubleshooting a Hard Drive" on page 159 for the appropriate drive(s) installed in your system. Remote Access Controller cable error or incorrect card in the RAC slot. RAC cables are not Check that the RAC cables connected, or RAC card is are connected, and that the installed in the wrong RAC card is installed in the expansion slot. correct expansion slot. See "RAC Card" on page 83. Remote Access Controller not installed in the RAC slot. RAC card is installed in Check that the RAC card is the wrong expansion slot. installed in the correct expansion slot. See "RAC Card" on page 83. Remote configuration update attempt failed System unable to process Retry Remote Remote Configuration Configuration. request. ROM bad checksum = address An expansion card is improperly installed or is faulty. Reseat the expansion cards. Ensure that all appropriate cables are securely connected to the expansion cards. If the problem persists, see "Troubleshooting Expansion Cards" on page 164. Sector not found Faulty hard drive. Seek error See "Troubleshooting a Hard Drive" on page 159. Seek operation failed About Your System 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198

About Your System
39
Read fault
Requested sector
not found
The operating system
cannot read from the hard
drive, the system could
not find a particular
sector on the disk, or the
requested sector is
defective.
Replace the diskette.
Ensure that the diskette
and hard drive cables are
properly connected. See
"Troubleshooting an
Optical Drive" on page 158,
or "Troubleshooting a Hard
Drive" on page 159 for the
appropriate drive(s)
installed in your system.
Remote Access
Controller cable
error or incorrect
card in the RAC
slot.
RAC cables are not
connected, or RAC card is
installed in the wrong
expansion slot.
Check that the RAC cables
are connected, and that the
RAC card is installed in the
correct expansion slot. See
"RAC Card" on page 83.
Remote Access
Controller not
installed in the
RAC slot.
RAC card is installed in
the wrong expansion slot.
Check that the RAC card is
installed in the correct
expansion slot. See "RAC
Card" on page 83.
Remote
configuration
update attempt
failed
System unable to process
Remote Configuration
request.
Retry Remote
Configuration.
ROM bad checksum =
address
An expansion card is
improperly installed or is
faulty.
Reseat the expansion cards.
Ensure that all appropriate
cables are securely
connected to the expansion
cards. If the problem
persists, see
"Troubleshooting
Expansion Cards" on
page 164.
Sector not found
Seek error
Seek operation
failed
Faulty hard drive.
See "Troubleshooting a
Hard Drive" on page 159.
Table 1-8.
System Messages
(continued)
Message
Causes
Corrective Actions