HP 3000dtn HP Business Inkjet 3000 series printers - (English) User Guide - Page 18

Setting up the printer, Step 1: Set up the printer

Get HP 3000dtn - Business Inkjet Color Printer PDF manuals and user guides View all HP 3000dtn manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Setting up the printer To set up the printer, complete the following steps. For illustrated setup information, see the setup poster. Step 1: Set up the printer 1 Select a location for the printer that is level, sturdy, and can support all corners of the printer, such as a low table. The location should be about 25 cm (10 inches) away from a wall to provide easy access to the rear of the printer for using Tray 1. 2 If your printer was shipped with Tray 3 or you purchased Tray 3 as an optional accessory, unpack Tray 3. Otherwise, go on to step 3. a Position Tray 3 in the location where you want to place the printer. b Remove the tape and packing materials from Tray 3, including the foam block located inside the tray. 3 Two people should lift the printer. Each person should grasp the printer in the front just under the lip below the LCD control panel, and in the rear by the indentation on either side of Tray 1. Alternately, each person can hold on to the bottom of the printer during lifting. WARNING! It is strongly recommended that two people lift or move the printer. The printer is top-heavy and can tip if lifted by only one person. The side of the printer that holds the ink cartridges and printheads is considerably heavier than the other side. WARNING! Do not attempt to move the printer by holding on to Tray 2 in the front or Tray 1 in the back. This can damage the printer and might cause you to lose your grip on the printer. 4 Move the printer to the prepared location. Be sure that the foam packing cushions are removed from the bottom of the printer. Gently place the printer on the prepared location. -Or- If installing Tray 3, align the front edge of the printer with the front edge of the Tray 3 base. Gently lower the printer onto the Tray 3 base. 2-4 ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
2-4
ENWW
Setting up the printer
To set up the printer, complete the following steps. For illustrated setup
information, see the setup poster.
Step 1: Set up the printer
1
Select a location for the printer that is level, sturdy, and can support
all corners of the printer, such as a low table. The location should
be about 25 cm (10 inches) away from a wall to provide easy
access to the rear of the printer for using Tray 1.
2
If your printer was shipped with Tray 3 or you purchased Tray 3 as
an optional accessory, unpack Tray 3. Otherwise, go on to step 3.
a
Position Tray 3 in the location where you want to place
the printer.
b
Remove the tape and packing materials from Tray 3, including
the foam block located inside the tray.
3
Two people should lift the printer. Each person should grasp the
printer in the front just under the lip below the LCD control panel,
and in the rear by the indentation on either side of Tray 1.
Alternately, each person can hold on to the bottom of the printer
during lifting.
WARNING!
It is strongly recommended that two people lift or move the printer.
The printer is top-heavy and can tip if lifted by only one person.
The side of the printer that holds the ink cartridges and printheads
is considerably heavier than the other side.
WARNING!
Do not attempt to move the printer by holding on to Tray 2 in the
front or Tray 1 in the back. This can damage the printer and might
cause you to lose your grip on the printer.
4
Move the printer to the prepared location. Be sure that the foam
packing cushions are removed from the bottom of the printer.
Gently place the printer on the prepared location.
-Or-
If installing Tray 3, align the front edge of the printer with the
front edge of the Tray 3 base. Gently lower the printer onto the
Tray 3 base.