HP xw8600 HP xw8600 Workstation Service and Technical Reference Guide - Page 106

Battery, Removing the battery

Get HP xw8600 - Workstation PDF manuals and user guides View all HP xw8600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 106 highlights

4. Open the PCI card retention clamp by pressing the retention clamp levers down to unsnap, and then rotating them up (1) as shown in the following figure. Figure 4-55 Installing a PCI card 5. Remove the PCI slot cover (2). 6. Align the PCI card keyway with the slot key, and then firmly seat the card in the slot (3). 7. Close the PCI retention clamp by rotating it downward and pressing the two green clamp levers from the rear panel of the chassis (4). If the PCI retention clamp levers do not close, ensure that all cards are properly seated, and then try again. Battery This section describes how to remove and install the battery. The battery that comes with the workstation provides power to the real-time clock and has a minimum lifetime of about three years. WARNING! This workstation includes a lithium battery. There is a risk of fire and chemical burn if the battery is handled improperly. Do not disassemble, crush, puncture, short external contacts, dispose in water or fire, or expose it to temperatures higher than 60°C (140°F). CAUTION: Before removing the battery, back up the CMOS settings in case they are lost when the battery is removed. To back up the CMOS settings, select the Save to Diskette option in the Computer Setup (F10) Utility. NOTE: Do not dispose of batteries, battery packs, and accumulators with general household waste. Removing the battery To remove the battery: 1. Disconnect power from the system (see Predisassembly procedures on page 52). 2. Remove the side access panel (see Removing the side access panel on page 57). 96 Chapter 4 Removal and replacement procedures ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
4.
Open the PCI card retention clamp by pressing the retention clamp levers down to unsnap, and
then rotating them up (1) as shown in the following figure.
Figure 4-55
Installing a PCI card
5.
Remove the PCI slot cover (2).
6.
Align the PCI card keyway with the slot key, and then firmly seat the card in the slot (3).
7.
Close the PCI retention clamp by rotating it downward and pressing the two green clamp levers
from the rear panel of the chassis (4).
If the PCI retention clamp levers do not close, ensure that all cards are properly seated, and then
try again.
Battery
This section describes how to remove and install the battery.
The battery that comes with the workstation provides power to the real-time clock and has a minimum
lifetime of about three years.
WARNING!
This workstation includes a lithium battery. There is a risk of fire and chemical burn if the
battery is handled improperly. Do not disassemble, crush, puncture, short external contacts, dispose in
water or fire, or expose it to temperatures higher than 60°C (140°F).
CAUTION:
Before removing the battery, back up the CMOS settings in case they are lost when the
battery is removed. To back up the CMOS settings, select the
Save to Diskette
option in the Computer
Setup (F10) Utility.
NOTE:
Do not dispose of batteries, battery packs, and accumulators with general household waste.
Removing the battery
To remove the battery:
1.
Disconnect power from the system (see
Predisassembly procedures
on page
52
).
2.
Remove the side access panel (see
Removing the side access panel
on page
57
).
96
Chapter 4
Removal and replacement procedures
ENWW