HP xw8600 HP xw8600 Workstation Service and Technical Reference Guide - Page 150

Table 5-18, POST error messages, continued

Get HP xw8600 - Workstation PDF manuals and user guides View all HP xw8600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 150 highlights

Table 5-18 POST error messages (continued) Screen message Probable cause Recommended action 207-Incompatible memory modules detected Single-bit ECC error. 1. Verify the memory module type. 2. Insert the DIMM in another memory socket. 3. Replace the memory module if the problem persists. 208-Two-DIMM configurations use slots one and five DIMMs are loaded in incorrect slots for Verify that the two DIMMs are installed in slots one and a two-DIMM configuration. five only. 209-Incompatible memory (FBDs) detected Incorrect memory module type in use. Verify that the memory modules are compatible with workstation requirements. 210-Mismatched memory (AMBs) detected Different memory module types are matched. Verify that compatible memory module types are used in matched pairs. 211-Memory warning condition detected Improper or defective memory module. Replace the memory module. 212-Failed Processor Processor has failed to initialize. 1. Reseat the processor in its socket. 2. If the processor does not respond, replace it. 213-Incompatible Memory Modules A memory module in the memory 1. Verify the memory module type. socket identified in the error message is missing critical SPD information, or 2. Insert the DIMM in another memory socket. is incompatible with the chipset. 3. Replace the module with a DIM conforming to the SPD standard. 214-DIMM Configuration Warning DIMMs are not installed correctly (not See the service label on the workstation access panel paired correctly). for the correct memory configurations, and reseat the DIMMs accordingly. 216-Memory Size Exceeds Maximum Supported The amount of memory installed exceeds that supported by the hardware. 1. Verify how much memory your system supports. 2. Remove the excess memory. 301-Keyboard Error Keyboard failure. 1. Reconnect the keyboard with the workstation powered off. 2. Check the connector for bent or missing pins. 3. Be sure that none of the keys are pressed. 4. Replace the keyboard. 303-Keyboard Controller Error I/O board keyboard controller is defective or is not set properly. 1. Reconnect the keyboard with the workstation powered off. 2. Replace the system board. 304-Keyboard or System Unit Error Keyboard failure. 1. Reconnect the keyboard with the workstation powered off. 2. Be sure that none of the keys are pressed. 3. Replace keyboard. 4. Replace system board. 510-Splash Screen image corrupted Splash Screen image has errors. Update system BIOS. 140 Chapter 5 System diagnostics and troubleshooting ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
Screen message
Probable cause
Recommended action
207—Incompatible memory
modules detected
Single-bit ECC error.
1.
Verify the memory module type.
2.
Insert the DIMM in another memory socket.
3.
Replace the memory module if the problem
persists.
208—Two-DIMM
configurations use slots one
and five
DIMMs are loaded in incorrect slots for
a two-DIMM configuration.
Verify that the two DIMMs are installed in slots one and
five only.
209—Incompatible memory
(FBDs) detected
Incorrect memory module type in use.
Verify that the memory modules are compatible with
workstation requirements.
210—Mismatched memory
(AMBs) detected
Different memory module types are
matched.
Verify that compatible memory module types are used
in matched pairs.
211—Memory warning
condition detected
Improper or defective memory module.
Replace the memory module.
212—Failed Processor
Processor has failed to initialize.
1.
Reseat the processor in its socket.
2.
If the processor does not respond, replace it.
213—Incompatible Memory
Modules
A memory module in the memory
socket identified in the error message
is missing critical SPD information, or
is incompatible with the chipset.
1.
Verify the memory module type.
2.
Insert the DIMM in another memory socket.
3.
Replace the module with a DIM conforming to the
SPD standard.
214—DIMM Configuration
Warning
DIMMs are not installed correctly (not
paired correctly).
See the service label on the workstation access panel
for the correct memory configurations, and reseat the
DIMMs accordingly.
216—Memory Size Exceeds
Maximum Supported
The amount of memory installed
exceeds that supported by the
hardware.
1.
Verify how much memory your system supports.
2.
Remove the excess memory.
301—Keyboard Error
Keyboard failure.
1.
Reconnect the keyboard with the workstation
powered off.
2.
Check the connector for bent or missing pins.
3.
Be sure that none of the keys are pressed.
4.
Replace the keyboard.
303—Keyboard Controller
Error
I/O board keyboard controller is
defective or is not set properly.
1.
Reconnect the keyboard with the workstation
powered
off.
2.
Replace the system board.
304—Keyboard or System
Unit Error
Keyboard failure.
1.
Reconnect the keyboard with the workstation
powered off.
2.
Be sure that none of the keys are pressed.
3.
Replace keyboard.
4.
Replace system board.
510—Splash Screen image
corrupted
Splash Screen image has errors.
Update system BIOS.
Table 5-18
POST error messages
(continued)
140
Chapter 5
System diagnostics and troubleshooting
ENWW