HP NetServer AA 6200 HP NetServer AA 6200 Solution Release 3.0 Messages - Page 224

This message is generated during CE boot when it is determined that two IOPs are

Get HP NetServer AA 6200 PDF manuals and user guides View all HP NetServer AA 6200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 224 highlights

Chapter 13 MtcMon Messages IOPn.MtcMon status: A CE protocol error was detected on IOPx during an IOPy remove or disable operation. Variables x - the ID of the IOP on which a protocol error was detected y - the ID of the IOP that was being removed or disabled when the error was detected Severity Warning Description When using the Endurance Manager to issue a request to shut down or disable an IOP, the Monitor performs a series of message exchanges between the local IOP and the CE. A protocol error was detected during this message exchange. Related Messages IOPn.MtcMon status: The IOP shutdown or disable operation failed. IOPn.MtcMon status: CEx has been removed from service. IOPn.MtcMon status: IOPx has been removed from service. Hardware/Software This message is usually generated as a result of a hardware failure occurring during the message exchange, or a software error. Action The IOP shutdown or disable operation is aborted when this message occurs. The message IOPn.MtcMon status: The IOP shutdown or disable operation failed is also generated. It is also possible that a secondary message occurs that results in removing the CE or an IOP. Report this message to your service provider. IOPn.MtcMon status: A conflict was detected during CE boot with remote IOPx. Variables x - the ID of the remote IOP that is attempting to boot the CE Severity Warning Description This message is generated during CE boot when it is determined that two IOPs are independently attempting to boot the CE. This occurs if either: • The IL cable is not properly connected • The IL is faulted, preventing the IOPs from communicating Related Messages IOPn.MtcMon status: The boot process has failed for CEy. IOPn.MtcMon status: The boot conflict could not be resolved. Hardware/Software A physical problem exists with the Interconnect between the two IOPs. Action When this situation occurs, this message is generated by both IOPs. The IOPs evaluate the information provided by the CE when the conflict occurs and determine from this information which IOP should drive the CE boot. No action is necessary unless this message is followed by the message IOPn.MtcMon status: The boot conflict could not be resolved. If these messages are reported sequentially, report this to your service provider. 214

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290
  • 291
  • 292
  • 293
  • 294
  • 295
  • 296
  • 297
  • 298
  • 299
  • 300
  • 301
  • 302
  • 303
  • 304
  • 305
  • 306
  • 307
  • 308
  • 309
  • 310
  • 311
  • 312
  • 313
  • 314
  • 315
  • 316
  • 317
  • 318
  • 319
  • 320
  • 321
  • 322
  • 323
  • 324
  • 325
  • 326
  • 327
  • 328
  • 329
  • 330
  • 331
  • 332
  • 333
  • 334
  • 335
  • 336
  • 337
  • 338
  • 339
  • 340
  • 341
  • 342
  • 343
  • 344
  • 345
  • 346
  • 347
  • 348
  • 349
  • 350
  • 351
  • 352
  • 353
  • 354
  • 355
  • 356
  • 357
  • 358
  • 359
  • 360
  • 361
  • 362
  • 363
  • 364
  • 365
  • 366
  • 367
  • 368
  • 369
  • 370
  • 371
  • 372
  • 373
  • 374
  • 375
  • 376
  • 377
  • 378
  • 379
  • 380
  • 381
  • 382
  • 383
  • 384
  • 385
  • 386
Chapter 13
MtcMon Messages
214
IOP
n
.MtcMon status: A CE protocol error was detected on IOP
x
during an IOP
y
remove or disable operation.
Variables
x
–
the ID of the IOP on which a protocol error was detected
y
–
the ID of the IOP that was being removed or disabled when the error was detected
Severity
Warning
Description
When using the Endurance Manager to issue a request to shut down or disable an IOP, the
Monitor performs a series of message exchanges between the local IOP and the CE. A protocol
error was detected during this message exchange.
Related Messages
IOP
n
.MtcMon status: The IOP shutdown or disable operation failed.
IOP
n
.MtcMon status: CE
x
has been removed from service.
IOP
n
.MtcMon status: IOP
x
has been removed from service.
Hardware/Software
This message is usually generated as a result of a hardware failure occurring during the
message exchange, or a software error.
Action
The IOP shutdown or disable operation is aborted when this message occurs. The message
IOP
n
.MtcMon status: The IOP shutdown or disable operation failed
is also
generated. It is also possible that a secondary message occurs that results in removing the CE
or an IOP. Report this message to your service provider.
IOP
n
.MtcMon status: A conflict was detected during CE boot with remote
IOP
x
.
Variables
x
–
the ID of the remote IOP that is attempting to boot the CE
Severity
Warning
Description
This message is generated during CE boot when it is determined that two IOPs are
independently attempting to boot the CE. This occurs if either:
•
The IL cable is not properly connected
•
The IL is
faulted,
preventing the IOPs from communicating
Related Messages
IOP
n
.MtcMon status: The boot process has failed for CE
y
.
IOP
n
.MtcMon status: The boot conflict could not be resolved.
Hardware/Software
A physical problem exists with the Interconnect between the two IOPs.
Action
When this situation occurs, this message is generated by both IOPs. The IOPs evaluate the
information provided by the CE when the conflict occurs and determine from this information
which IOP should drive the CE boot. No action is necessary unless this message is followed
by the message
IOP
n
.MtcMon status: The boot conflict could not be
resolved
. If these messages are reported sequentially, report this to your service provider.