Yamaha AW16G Owner's Manual - Page 205
MIDI format list, 4.2. BULK DUMP / BULK DUMP REQUEST
View all Yamaha AW16G manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 205 highlights
3.1.9. Program Change Mode Enable/disable reception and transmission. If MIDI Rx Ch is set to ALL, these messages will be received regardless of their MIDI channel. 3.1.10. Control Change Mode If this is enabled, you can specify the correspondence between control numbers and operations of the mixer section. For mode 1, transmission and reception will occur without regard to the MIDI Tx Ch and MIDI Rx Ch settings. For modes 2 and 3, reception will occur without regard to MIDI channel if you set MIDI Rx Ch to ALL. 3.2. MIDI BULK DUMP Controls transmission of Bulk Dump and Bulk Dump Request. 3.2.1. BULK DUMP Category Selects the type of parameters for Dump or Dump Request. 3.2.1.1. SCENE Mixer scene settings. E.BUF is the current state, 01-96 are stored scenes. ALL selects all scenes. 3.2.1.2. LIBRARY All memory settings for all libraries (EQ / EFFECT / DYNAMICS / CHANNEL). 3.2.1.3. SYSTEM Settings that apply to the entire AW16G. 3.2.1.4. REMOTE Settings for the MIDI Remote function. 3.2.1.5. PROGRAM CHANGE TABLE This is the Program Change Table. 3.2.1.6. ALL All of the above settings. 3.2.2. INTERVAL Specifies the interval at which consecutive Bulk Dump or Bulk Dump Request messages will be transmitted. Increase this setting if the receiving device fails to receive all of the bulk data. 3.2.3. RX DISABLE If RX Disable is turned on, no Bulk Dump or Bulk Dump Request messages will be received. 3.2.4. REQUEST Transmits the selected Bulk Dump Request. 3.2.5. TRANSMIT Transmits the selected Bulk Dump. 3.3. MIDI PROGRAM CHANGE TABLE This table allows you to freely specify the correspondence between Program Change No. and Scene No. This table is used for conversion for both transmission and reception. 4. MIDI format list 4.1. CHANNEL MESSAGE Command 8n NOTE OFF 9n NOTE ON Bn CONTROL CHANGE Cn PROGRAM CHANGE Rx/Tx Rx Rx Rx/Tx Rx/Tx function Control the internal effect Control the internal effect Edit parameters Switch scene memories 4.2. SYSTEM COMMON MESSAGE Command Rx/Tx function F1 MIDI TIME CODE Rx/Tx MTC transmission F2 SONG POSITION POINTER Tx Song position transmission 4.3. SYSTEM REALTIME MESSAGE Command F8 TIMING CLOCK FA START FB CONTINUE FC STOP FE ACTIVE SENSING FF RESET Rx/Tx Tx Tx Tx Tx Rx Rx function MIDI Clock transmission Start command transmission Continue command transmission Stop command transmit Check MIDI cable connections Clear running status 4.4. SYSTEM EXCLUSIVE MESSAGE 4.4.1. REALTIME SYSTEM EXCLUSIVE 4.4.1.1. MMC Command 01 STOP 02 PLAY 03 DEFERRED PLAY 04 FAST FORWARD 05 REWIND 06 RECORD STROBE 07 RECORD EXIT 0F RESET 44 LOCATE Rx/Tx Rx/Tx Rx Rx/Tx Rx/TX Rx/Tx Rx Rx Rx/Tx Rx/Tx function Transport stop Transport play Transport play Transport fast-forward Transport rewind Transport punch-in record Transport punch-out MMC reset Transport locate 4.4.2. BULK DUMP / BULK DUMP REQUEST Data Name 'M' 'S' 'R' 'Q' 'Y' 'E' 'H' 'P' Rx/Tx Rx/Tx Rx/Tx Rx/Tx Rx/Tx Rx/Tx Rx/Tx Rx/Tx Rx/Tx function Scene Memory & Request System Memory & Request Remote Memory & Request Equalizer Library & Request Dynamics Library & Request Effect Library & Request Channel Library & Request Program Change Table & Request Appendix 205