Sony TRV940E Operating Instructions - Page 321

Maintenance information and precautions Инфоpмaция по yxодy зa aппapaтом и мepы пpeдоcтоpожноcти Moisture condensation If your camcorder is brought directly from a cold place to a warm place, moisture may condense inside your camcorder, on the surface of the tape, or on the lens. In this state, the tape may stick to the head drum and be damaged or your camcorder may not operate correctly. If there is moisture inside your camcorder, the beep and the % indicator flashes. When the Z indicator flashes at the same time, the cassette is inserted in your camcorder. If moisture condenses on the lens, the indicator will not appear. If moisture condensation has occurred None of the functions except cassette ejection will work. Eject the cassette, turn off your camcorder, and leave it for about one hour with the cassette lid open. Your camcorder can be used again if the % indicator does not appear when the power is turned on again. If moisture starts to condense, your camcorder sometimes cannot detect condensation. If this happens, the cassette is sometimes not ejected for 10 seconds after the cassette lid is opened. This is not a malfunction. Do not close the cassette lid until the cassette is ejected. Note on moisture condensation Moisture may condense when you bring your camcorder from a cold place into a warm place (or vice versa) or when you use your camcorder in a hot place as follows: •You bring your camcorder from a ski slope into a place warmed up by heating device. •You bring your camcorder from an air- conditioned car or room into a hot place outside. •You use your camcorder after a squall or a shower. •You use your camcorder in a high temperature and humid place. How to prevent moisture condensation When you bring your camcorder from a cold place into a warm place, put your camcorder in a plastic bag and tightly seal it. Remove the bag when the air temperature inside the plastic bag has reached the surrounding temperature (after about one hour). Кондeнcaция влaги Ecли видeокaмepa пpинeceнa из x ecтa в тeплоe помeщeниe, то внyтpи видeокaмepы, нa повepxноcти лe a объeктивe можeт пp eнcaция влaги. B тaком cоc eнтa можeт пpилипнyть к бapaбaнy yдeт повpeждeнa eокaмepa нe cможeт paботaть нaдлeжaщим обpaзом. Ecли внyтpи видeокaмepы пpоизошлa кондeнcaция влa pозвyчит зyммepный cигнaл и бyдeт мигa aтоp%. Ec peмe ae aтоp Z a acceтa вcтaвлeнa в видeокaмepy. Ecли влaгa cкондeнcиpовaлacь нa объeктивe, индикaтоp cя нe бyдeт. Ecли пpоизошлa кондeнcaция влaги Hи однa из фy pомe извлeчeния кacceты, нe бyдeт paботaть. Bыньтe кacceтy e видeокaмepy и оcтaвьтe ee пpимepно нa один чac c откpытой кp acce ceкa. Ecли пp p e a aтоp % нe cя, Bы можeтe cновa aтьcя видeокaмepой. Ecли нaчнeт кондeнcиpовaтьcя влaгa, видeокaмepa нe вceгдa cможe peдeлить. Ec pоизойдe a поcлe откpытия кpышки кacce ceкa кacceтa нe бyдeт извлeкaтьcя в тeчeниe 10 ceкy e являeтcя нeиcпpaвноcтью. He зaкpывaйтe кpышкy кacce ceкa, покa нe бyдeт извлeчeнa кacceтa. Пpимeчaниe eнcaции влaги Bлaгa можeт обpaзовaтьcя, ecли пepeнecти видeокaмepy из x ecтa в тeплоe (или нaобоp pи иc a eокaмepы в жapком мecтe в cлeдyющиx cлyчaяx: • Bидeокaмepa пpинeceнa c cклонa в помeщeниe, гдe paботaeт обогpeвaтeль. • Bидeокaмepa пpинeceнa из a помeщe pыx paботae ep, в жapкоe мecто внe помeщeния. • Bидeокaмepa иcпользyeтcя поcлe гp Bидeокaмepa иcпользyeтcя в жapком мecтe или мecтe c повышe aжноcтью. Кaк пpeдотвpa eнcaцию влaги Ecли видeокaмepa пpинeceнa из x ecтa в тeплоe e видeокaмepy e aкe aклeйтe eго. Bыньтe видeокaмepy e aкeтa, когдa тeмпepaтypa воздyxa внyтpи пaкeтa доcтигнeт тeмпepaтypы окpyжaющe yxa (пp eльно чepe ac). 321 Additional Information