Home » D-Link Manuals » Hubs & Switches » D-Link DES-3528 » Manual Viewer

D-Link DES-3528 Product Manual - Page 150

IPv4 Route Table, IPv4 Static/Default Route Settings window

UPC - 790069314346

Add to My Manuals
Save this manual to your list of manuals

Page 150 highlights

xStack® DES-3528/DES-3552 Series Layer 2 Stackable Fast Ethernet Managed Switch Web UI Reference Guide The Switch also supports a floating static route, which means that the user may create an alternative static route to a different next hop. This secondary next hop device route is considered as a backup static route for when the primary static route is down. If the primary route is lost, the backup route will uplink and its status will become Active. To view the following window, click L3 Features > IPv4 Static/Default Route Settings, as shown below: Figure 5-2 IPv4 Static/Default Route Settings window The fields that can be configured are described below: Parameter Description IP Address This field allows the entry of an IPv4 address to be assigned to the Static or Default route. Netmask This field allows the entry of a subnet mask to be applied to the corresponding subnet mask of the IP address. Gateway This field allows the entry of a Gateway IP Address to be applied to the corresponding gateway of the IP address. Metric (1-65535) Represents the metric value of the IP interface entered into the table. This field may read a number between 1 and 65535. Backup State Each IP address can only have one primary route, while other routes should be assigned to the backup state. When the primary route failed, switch will try the backup routes according to the order learnt by the routing table until route success. The field represents the Backup state that the Static and Default Route is configured for. Click the Apply button to accept the changes made. IPv4 Route Table The IP routing table stores all the external routes information of the Switch. On this page the user can view all the external route information on the Switch. To view the following window, click L3 Features > IPv4 Route Table, as shown below: Figure 5-3 IPv4 Route Table window 141

Section	Page
Intended Readers	10
Typographical Conventions	10
Notes, Notices and Cautions	10
Chapter 1 Web-based Switch Configuration	11
Introduction	11
Login to the Web Manager	11
Web-based User Interface	12
Web Pages	13
Chapter 2 System Configuration	14
Device Information	14
System Information Settings	15
Dual Configuration Settings	16
Firmware Information Settings	17
Port Configuration	18
PoE	21
Serial Port Settings	24
System Log configuration	25
Time Range Settings	29
Time Settings	29
User Accounts Settings	30
Stacking	31
Chapter 3 Management	35
ARP	35
Gratuitous ARP	37
IPv6 Neighbor Settings	38
IP Interface	39
Management Settings	43
Session Table	44
Single IP Management	44
SNMP Settings	54
Telnet Settings	64
Web Settings	64
Chapter 4 L2 Features	65
VLAN	65
Q-in-Q	88
Layer 2 Protocol Tunneling Settings	90
Spanning Tree	91
Link Aggregation	100
FDB	103
L2 Multicast Control	107
Multicast Filtering	132
ERPS Settings	136
LLDP	139
Chapter 5 L3 Features	149
Local Route Settings	149
IPv4 Static/Default Route Settings	149
IPv4 Route Table	150
IPv6 Static/Default Route Settings	151
IPv6 Route Table	151
Policy Route Settings	152
IP Forwarding Table	153
Chapter 6 QoS	154
802.1p Settings	156
Bandwidth Control	159
Traffic Control Settings	161
DSCP	164
HOL Blocking Prevention	167
Scheduling Settings	168
SRED	171
Chapter 7 ACL	174
ACL Configuration Wizard	174
Access Profile List	175
CPU Access Profile List	193
ACL Finder	207
ACL Flow Meter	208
Chapter 8 Security	211
802.1X	211
RADIUS	224
IP-MAC-Port Binding (IMPB)	229
MAC-based Access Control (MAC)	236
Web-based Access Control (WAC)	240
Japanese Web-based Access Control (JWAC)	245
Compound Authentication	252
Port Security	256
ARP Spoofing Prevention Settings	258
BPDU Attack Protection	259
Loopback Detection Settings	261
Traffic Segmentation Settings	262
NetBIOS Filtering Settings	263
DHCP Server Screening	264
Access Authentication Control	265
SSL Settings	274
SSH	276
Trusted Host Settings	280
Safeguard Engine Settings	281
Chapter 9 Network Application	284
DHCP	284
DNS	296
PPPoE Circuit ID Insertion Settings	298
SNTP	299
Chapter 10 OAM	302
CFM	302
Ethernet OAM	311
DULD Settings	315
Cable Diagnostics	316
Chapter 11 Monitoring	318
Utilization	318
Statistics	320
Mirror	332
sFlow	334
Ping Test	337
Trace Route	338
Peripheral	340
Chapter 12 Save and Tools	341
Save Configuration ID 1	341
Save Configuration ID 2	341
Save Log	342
Save All	342
Stacking Information	342
Download Firmware	344
Download Configuration File	344
Upload Configuration File	345
Upload Log File	346
Reset	347
Reboot System	347
Appendix A Mitigating ARP Spoofing Attacks Using Packet Content ACL	348
How Address Resolution Protocol Works	348
How ARP Spoofing Attacks a Network	350
Prevent ARP Spoofing via Packet Content ACL	351
Configuration	351
Appendix B System Log and Trap List	354
System Log Entries	354
DES-3528/DES-3552 Series Trap List	362
Proprietary Trap List	362
Appendix C Password Recovery Procedure	365

Match case Limit results 1 per page

xStack® DES-3528/DES-3552 Series Layer 2 Stackable Fast Ethernet Managed Switch Web UI Reference Guide

The Switch also supports a floating static route, which means that the user may create an alternative static route to a

different next hop. This secondary next hop device route is considered as a backup static route for when the primary

static route is down. If the primary route is lost, the backup route will uplink and its status will become Active.

To view the following window, click

L3 Features > IPv4 Static/Default Route Settings

, as shown below:

Figure 5-2 IPv4 Static/Default Route Settings window

The fields that can be configured are described below:

Parameter

Description

IP Address

This field allows the entry of an IPv4 address to be assigned to the Static or Default route.

Netmask

This field allows the entry of a subnet mask to be applied to the corresponding subnet mask

of the IP address.

Gateway

This field allows the entry of a Gateway IP Address to be applied to the corresponding

gateway of the IP address.

Metric (1-65535)

Represents the metric value of the IP interface entered into the table. This field may read a

number between

and

65535

Backup State

Each IP address can only have one primary route, while other routes should be assigned to

the backup state. When the primary route failed, switch will try the backup routes according

to the order learnt by the routing table until route success. The field represents the Backup

state that the Static and Default Route is configured for.

Click the

Apply

button to accept the changes made.

IPv4 Route Table

The IP routing table stores all the external routes information of the Switch. On this page the user can view all the

external route information on the Switch.

To view the following window, click

L3 Features > IPv4 Route Table

, as shown below:

Figure 5-3 IPv4 Route Table window

141