D-Link DES-3528 Product Manual - Page 270

xStack® DES-3528/DES-3552 Series Layer 2 Stackable Fast Ethernet Managed Switch Web UI Reference Guide

NOTE:

The user must configure Authentication Server Hosts using the Authentication Server Hosts

window before adding hosts to the list. Authentication Server Hosts must be configured for their

specific protocol on a remote centralized server before this function can work properly.

NOTE:

The three built-in server groups can only have server hosts running the same TACACS daemon.

TACACS/XTACACS/TACACS+ protocols are separate entities and are not compatible with each

other.

Authentication Server Settings

User-defined Authentication Server Hosts for the TACACS / XTACACS / TACACS+ / RADIUS security protocols can

be set on the Switch. When a user attempts to access the Switch with Authentication Policy enabled, the Switch will

send authentication packets to a remote TACACS / XTACACS / TACACS+ / RADIUS server host on a remote host.

The TACACS / XTACACS / TACACS+ / RADIUS server host will then verify or deny the request and return the

appropriate message to the Switch. More than one authentication protocol can be run on the same physical server host

but, remember that TACACS / XTACACS / TACACS+ / RADIUS are separate entities and are not compatible with

each other. The maximum supported number of server hosts is 16.

To view this window, click

Security > Access Authentication Control > Authentication Server Settings

, as shown

below:

Figure 8-65 Authentication Server Settings window

The fields that can be configured are described below:

Parameter

Description

IP Address

The IP address of the remote server host to add.

Protocol

The protocol used by the server host. The user may choose one of the following:

TACACS

- Enter this parameter if the server host utilizes the TACACS protocol.

XTACACS

- Enter this parameter if the server host utilizes the XTACACS protocol.

TACACS+

- Enter this parameter if the server host utilizes the TACACS+ protocol.

RADIUS

- Enter this parameter if the server host utilizes the RADIUS protocol.

Key (Max: 254

characters)

Authentication key to be shared with a configured TACACS+ or RADIUS servers only.

Specify an alphanumeric string up to 254 characters.

Port (1-65535)

Enter a number between

1

and

65535

to define the virtual port number of the

authentication protocol on a server host. The default port number is

49

for

TACACS/XTACACS/TACACS+ servers and

1813

for RADIUS servers but the user

may set a unique port number for higher security.

Timeout (1-255)

Enter the time in seconds the Switch will wait for the server host to reply to an

authentication request. The default value is

5

seconds.

Retransmit (1-20)

Enter the value in the retransmit field to change how many times the device will resend

an authentication request when the TACACS server does not respond.

Click the

Apply

button to accept the changes made.

261

Section	Page
Intended Readers	10
Typographical Conventions	10
Notes, Notices and Cautions	10
Chapter 1 Web-based Switch Configuration	11
Introduction	11
Login to the Web Manager	11
Web-based User Interface	12
Web Pages	13
Chapter 2 System Configuration	14
Device Information	14
System Information Settings	15
Dual Configuration Settings	16
Firmware Information Settings	17
Port Configuration	18
PoE	21
Serial Port Settings	24
System Log configuration	25
Time Range Settings	29
Time Settings	29
User Accounts Settings	30
Stacking	31
Chapter 3 Management	35
ARP	35
Gratuitous ARP	37
IPv6 Neighbor Settings	38
IP Interface	39
Management Settings	43
Session Table	44
Single IP Management	44
SNMP Settings	54
Telnet Settings	64
Web Settings	64
Chapter 4 L2 Features	65
VLAN	65
Q-in-Q	88
Layer 2 Protocol Tunneling Settings	90
Spanning Tree	91
Link Aggregation	100
FDB	103
L2 Multicast Control	107
Multicast Filtering	132
ERPS Settings	136
LLDP	139
Chapter 5 L3 Features	149
Local Route Settings	149
IPv4 Static/Default Route Settings	149
IPv4 Route Table	150
IPv6 Static/Default Route Settings	151
IPv6 Route Table	151
Policy Route Settings	152
IP Forwarding Table	153
Chapter 6 QoS	154
802.1p Settings	156
Bandwidth Control	159
Traffic Control Settings	161
DSCP	164
HOL Blocking Prevention	167
Scheduling Settings	168
SRED	171
Chapter 7 ACL	174
ACL Configuration Wizard	174
Access Profile List	175
CPU Access Profile List	193
ACL Finder	207
ACL Flow Meter	208
Chapter 8 Security	211
802.1X	211
RADIUS	224
IP-MAC-Port Binding (IMPB)	229
MAC-based Access Control (MAC)	236
Web-based Access Control (WAC)	240
Japanese Web-based Access Control (JWAC)	245
Compound Authentication	252
Port Security	256
ARP Spoofing Prevention Settings	258
BPDU Attack Protection	259
Loopback Detection Settings	261
Traffic Segmentation Settings	262
NetBIOS Filtering Settings	263
DHCP Server Screening	264
Access Authentication Control	265
SSL Settings	274
SSH	276
Trusted Host Settings	280
Safeguard Engine Settings	281
Chapter 9 Network Application	284
DHCP	284
DNS	296
PPPoE Circuit ID Insertion Settings	298
SNTP	299
Chapter 10 OAM	302
CFM	302
Ethernet OAM	311
DULD Settings	315
Cable Diagnostics	316
Chapter 11 Monitoring	318
Utilization	318
Statistics	320
Mirror	332
sFlow	334
Ping Test	337
Trace Route	338
Peripheral	340
Chapter 12 Save and Tools	341
Save Configuration ID 1	341
Save Configuration ID 2	341
Save Log	342
Save All	342
Stacking Information	342
Download Firmware	344
Download Configuration File	344
Upload Configuration File	345
Upload Log File	346
Reset	347
Reboot System	347
Appendix A Mitigating ARP Spoofing Attacks Using Packet Content ACL	348
How Address Resolution Protocol Works	348
How ARP Spoofing Attacks a Network	350
Prevent ARP Spoofing via Packet Content ACL	351
Configuration	351
Appendix B System Log and Trap List	354
System Log Entries	354
DES-3528/DES-3552 Series Trap List	362
Proprietary Trap List	362
Appendix C Password Recovery Procedure	365

D-Link DES-3528 Product Manual - Page 270

Authentication Server Settings

Page 270 highlights