Home » D-Link Manuals » Hubs & Switches » D-Link DES-3528 » Manual Viewer

D-Link DES-3528 Product Manual - Page 29

Time Range Settings, Time Settings, Apply, System, Configuration > Time Range Settings

UPC - 790069314346

Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

xStack® DES-3528/DES-3552 Series Layer 2 Stackable Fast Ethernet Managed Switch Web UI Reference Guide are Emergency (0), Alert (1), Critical (2), Error (3), Warning (4), Notice (5), Information(6) and Debug(7). Click the Apply button to accept the changes made. Time Range Settings Time range is a time period that the respective function will take an effect on, such as ACL. For example, the administrator can configure the time based ACL to allow users to surf the Internet on every Saturday and every Sunday, meanwhile to deny users to surf the Internet on weekdays. The user may enter up to 64 time range entries on the Switch. To view the following window, click System Configuration > Time Range Settings, as shown below: Figure 2-15 Time Range Settings window The fields that can be configured are described below: Parameter Description Range Name Enter a name of no more than 32 alphanumeric characters that will be used to identify this time range on the Switch. This range name will be used in the Access Profile table to identify the access profile and associated rule to be enabled during this time range. Hours This parameter is used to set the time in the day that this time range is to be enabled using the following parameters: Start Time - Use this parameter to identify the starting time of the time range, in hours, minutes and seconds, based on the 24-hour time system. End Time - Use this parameter to identify the ending time of the time range, in hours, minutes and seconds, based on the 24-hour time system. Weekdays Use the check boxes to select the corresponding days of the week that this time range is to be enabled. Tick the Select All Days check box to configure this time range for every day of the week. Click the Apply button to accept the changes made. Current configured entries will be displayed in the table in the bottom half of the window shown above. Time Settings Users can configure the time settings for the Switch. To view the following window, click System Configuration > Time Settings, as shown below: 20

Section	Page
Intended Readers	10
Typographical Conventions	10
Notes, Notices and Cautions	10
Chapter 1 Web-based Switch Configuration	11
Introduction	11
Login to the Web Manager	11
Web-based User Interface	12
Web Pages	13
Chapter 2 System Configuration	14
Device Information	14
System Information Settings	15
Dual Configuration Settings	16
Firmware Information Settings	17
Port Configuration	18
PoE	21
Serial Port Settings	24
System Log configuration	25
Time Range Settings	29
Time Settings	29
User Accounts Settings	30
Stacking	31
Chapter 3 Management	35
ARP	35
Gratuitous ARP	37
IPv6 Neighbor Settings	38
IP Interface	39
Management Settings	43
Session Table	44
Single IP Management	44
SNMP Settings	54
Telnet Settings	64
Web Settings	64
Chapter 4 L2 Features	65
VLAN	65
Q-in-Q	88
Layer 2 Protocol Tunneling Settings	90
Spanning Tree	91
Link Aggregation	100
FDB	103
L2 Multicast Control	107
Multicast Filtering	132
ERPS Settings	136
LLDP	139
Chapter 5 L3 Features	149
Local Route Settings	149
IPv4 Static/Default Route Settings	149
IPv4 Route Table	150
IPv6 Static/Default Route Settings	151
IPv6 Route Table	151
Policy Route Settings	152
IP Forwarding Table	153
Chapter 6 QoS	154
802.1p Settings	156
Bandwidth Control	159
Traffic Control Settings	161
DSCP	164
HOL Blocking Prevention	167
Scheduling Settings	168
SRED	171
Chapter 7 ACL	174
ACL Configuration Wizard	174
Access Profile List	175
CPU Access Profile List	193
ACL Finder	207
ACL Flow Meter	208
Chapter 8 Security	211
802.1X	211
RADIUS	224
IP-MAC-Port Binding (IMPB)	229
MAC-based Access Control (MAC)	236
Web-based Access Control (WAC)	240
Japanese Web-based Access Control (JWAC)	245
Compound Authentication	252
Port Security	256
ARP Spoofing Prevention Settings	258
BPDU Attack Protection	259
Loopback Detection Settings	261
Traffic Segmentation Settings	262
NetBIOS Filtering Settings	263
DHCP Server Screening	264
Access Authentication Control	265
SSL Settings	274
SSH	276
Trusted Host Settings	280
Safeguard Engine Settings	281
Chapter 9 Network Application	284
DHCP	284
DNS	296
PPPoE Circuit ID Insertion Settings	298
SNTP	299
Chapter 10 OAM	302
CFM	302
Ethernet OAM	311
DULD Settings	315
Cable Diagnostics	316
Chapter 11 Monitoring	318
Utilization	318
Statistics	320
Mirror	332
sFlow	334
Ping Test	337
Trace Route	338
Peripheral	340
Chapter 12 Save and Tools	341
Save Configuration ID 1	341
Save Configuration ID 2	341
Save Log	342
Save All	342
Stacking Information	342
Download Firmware	344
Download Configuration File	344
Upload Configuration File	345
Upload Log File	346
Reset	347
Reboot System	347
Appendix A Mitigating ARP Spoofing Attacks Using Packet Content ACL	348
How Address Resolution Protocol Works	348
How ARP Spoofing Attacks a Network	350
Prevent ARP Spoofing via Packet Content ACL	351
Configuration	351
Appendix B System Log and Trap List	354
System Log Entries	354
DES-3528/DES-3552 Series Trap List	362
Proprietary Trap List	362
Appendix C Password Recovery Procedure	365

Match case Limit results 1 per page

xStack® DES-3528/DES-3552 Series Layer 2 Stackable Fast Ethernet Managed Switch Web UI Reference Guide

are

Emergency (0), Alert (1), Critical (2), Error (3), Warning (4), Notice (5), Information(6)

and

Debug(7).

Click the

Apply

button to accept the changes made.

Time Range Settings

Time range is a time period that the respective function will take an effect on, such as ACL. For example, the

administrator can configure the time based ACL to allow users to surf the Internet on every Saturday and every Sunday,

meanwhile to deny users to surf the Internet on weekdays.

The user may enter up to 64 time range entries on the Switch.

To view the following window, click

System

Configuration > Time Range Settings

, as shown below:

Figure 2-15 Time Range Settings window

The fields that can be configured are described below:

Parameter

Description

Range Name

Enter a name of no more than 32 alphanumeric characters that will be used to identify this time

range on the Switch. This range name will be used in the Access Profile

table to identify the

access profile and associated rule to be enabled during this time range.

Hours

This parameter is used to set the time in the day that this time range is to be enabled using the

following parameters:

Start Time

- Use this parameter to identify the starting time of the time range, in hours, minutes

and seconds, based on the 24-hour time system.

End Time

- Use this parameter to identify the ending time of the time range, in hours, minutes

and seconds, based on the 24-hour time system.

Weekdays

Use the check boxes to select the corresponding days of the week that this time range is to be

enabled. Tick the Select All Days check box to configure this time range for every day of the

week.

Click the

Apply

button to accept the changes made. Current configured entries will be displayed in the table in the

bottom half of the window shown above.

Time Settings

Users can configure the time settings for the Switch.

To view the following window, click

System

Configuration > Time Settings

, as shown below: