Home » D-Link Manuals » Hubs & Switches » D-Link DES-3528 » Manual Viewer

D-Link DES-3528 Product Manual - Page 264

DHCP Server Screening, DHCP Server Screening Port Settings

UPC - 790069314346

Add to My Manuals
Save this manual to your list of manuals

Page 264 highlights

xStack® DES-3528/DES-3552 Series Layer 2 Stackable Fast Ethernet Managed Switch Web UI Reference Guide DHCP Server Screening This function allows the user to not only to restrict all DHCP Server packets but also to receive any specified DHCP server packet by any specified DHCP client, it is useful when one or more DHCP servers are present on the network and both provide DHCP services to different distinct groups of clients. The first time the DHCP filter is enabled it will create both an access profile entry and an access rule per port entry, it will also create other access rules. These rules are used to block all DHCP server packets. In addition to a permit DHCP entry it will also create one access profile and one access rule entry the first time the DHCP client MAC address is used as the client MAC address. The Source IP address is the same as the DHCP server's IP address (UDP port number 67). These rules are used to permit the DHCP server packets with specific fields, which the user has configured. When DHCP Server filter function is enabled all DHCP Server packets will be filtered from a specific port. DHCP Server Screening Port Settings The Switch supports DHCP Server Screening, a feature that denies access to rogue DHCP servers. When the DHCP server filter function is enabled, all DHCP server packets will be filtered from a specific port. To view this window, click Security > DHCP Server Screening > DHCP Server Screening Port Settings, as shown below: Figure 8-58 DHCP Server Screening Port Settings window The fields that can be configured are described below: 255

Section	Page
Intended Readers	10
Typographical Conventions	10
Notes, Notices and Cautions	10
Chapter 1 Web-based Switch Configuration	11
Introduction	11
Login to the Web Manager	11
Web-based User Interface	12
Web Pages	13
Chapter 2 System Configuration	14
Device Information	14
System Information Settings	15
Dual Configuration Settings	16
Firmware Information Settings	17
Port Configuration	18
PoE	21
Serial Port Settings	24
System Log configuration	25
Time Range Settings	29
Time Settings	29
User Accounts Settings	30
Stacking	31
Chapter 3 Management	35
ARP	35
Gratuitous ARP	37
IPv6 Neighbor Settings	38
IP Interface	39
Management Settings	43
Session Table	44
Single IP Management	44
SNMP Settings	54
Telnet Settings	64
Web Settings	64
Chapter 4 L2 Features	65
VLAN	65
Q-in-Q	88
Layer 2 Protocol Tunneling Settings	90
Spanning Tree	91
Link Aggregation	100
FDB	103
L2 Multicast Control	107
Multicast Filtering	132
ERPS Settings	136
LLDP	139
Chapter 5 L3 Features	149
Local Route Settings	149
IPv4 Static/Default Route Settings	149
IPv4 Route Table	150
IPv6 Static/Default Route Settings	151
IPv6 Route Table	151
Policy Route Settings	152
IP Forwarding Table	153
Chapter 6 QoS	154
802.1p Settings	156
Bandwidth Control	159
Traffic Control Settings	161
DSCP	164
HOL Blocking Prevention	167
Scheduling Settings	168
SRED	171
Chapter 7 ACL	174
ACL Configuration Wizard	174
Access Profile List	175
CPU Access Profile List	193
ACL Finder	207
ACL Flow Meter	208
Chapter 8 Security	211
802.1X	211
RADIUS	224
IP-MAC-Port Binding (IMPB)	229
MAC-based Access Control (MAC)	236
Web-based Access Control (WAC)	240
Japanese Web-based Access Control (JWAC)	245
Compound Authentication	252
Port Security	256
ARP Spoofing Prevention Settings	258
BPDU Attack Protection	259
Loopback Detection Settings	261
Traffic Segmentation Settings	262
NetBIOS Filtering Settings	263
DHCP Server Screening	264
Access Authentication Control	265
SSL Settings	274
SSH	276
Trusted Host Settings	280
Safeguard Engine Settings	281
Chapter 9 Network Application	284
DHCP	284
DNS	296
PPPoE Circuit ID Insertion Settings	298
SNTP	299
Chapter 10 OAM	302
CFM	302
Ethernet OAM	311
DULD Settings	315
Cable Diagnostics	316
Chapter 11 Monitoring	318
Utilization	318
Statistics	320
Mirror	332
sFlow	334
Ping Test	337
Trace Route	338
Peripheral	340
Chapter 12 Save and Tools	341
Save Configuration ID 1	341
Save Configuration ID 2	341
Save Log	342
Save All	342
Stacking Information	342
Download Firmware	344
Download Configuration File	344
Upload Configuration File	345
Upload Log File	346
Reset	347
Reboot System	347
Appendix A Mitigating ARP Spoofing Attacks Using Packet Content ACL	348
How Address Resolution Protocol Works	348
How ARP Spoofing Attacks a Network	350
Prevent ARP Spoofing via Packet Content ACL	351
Configuration	351
Appendix B System Log and Trap List	354
System Log Entries	354
DES-3528/DES-3552 Series Trap List	362
Proprietary Trap List	362
Appendix C Password Recovery Procedure	365

Match case Limit results 1 per page

xStack® DES-3528/DES-3552 Series Layer 2 Stackable Fast Ethernet Managed Switch Web UI Reference Guide

DHCP Server Screening

This function allows the user to not only to restrict all DHCP Server packets but also to receive any specified DHCP

server packet by any specified DHCP client, it is useful when one or more DHCP servers are present on the network

and both provide DHCP services to different distinct groups of clients.

The first time the DHCP filter is enabled it will create both an access profile entry and an access rule per port entry, it

will also create other access rules. These rules are used to block all DHCP server packets. In addition to a permit

DHCP entry it will also create one access profile and one access rule entry the first time the DHCP client MAC address

is used as the client MAC address. The Source IP address is the same as the DHCP server’s IP address (UDP port

number 67). These rules are used to permit the DHCP server packets with specific fields, which the user has

configured.

When DHCP Server filter function is enabled all DHCP Server packets will be filtered from a specific port.

DHCP Server Screening Port Settings

The Switch supports DHCP Server Screening, a feature that denies access to rogue DHCP servers. When the DHCP

server filter function is enabled, all DHCP server packets will be filtered from a specific port.

To view this window, click

Security > DHCP Server Screening > DHCP Server Screening Port Settings

, as shown

below:

Figure 8-58 DHCP Server Screening Port Settings window

The fields that can be configured are described below:

255