HP Designjet L28500 HP Designjet L28500 Printer Series - User's guide - Page 52

The edge holders

Get HP Designjet L28500 PDF manuals and user guides View all HP Designjet L28500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

7. Press the OK button on the front panel. The front panel displays the amount of printed substrate that is on the take-up reel. 8. Unlock the take-up reel by lifting both levers. 9. Remove the roll from the printer, pulling out the end on the right side of the printer first. Do not insert your fingers into the spindle supports during the removal process. 10. To remove the roll from the printer after you have unloaded the take-up reel, see Unload a roll from the printer on page 36. The edge holders The edge holders are designed to prevent the edges of the substrate from rising while printing is in progress. They are recommended for textile and double-sided printing (even if the front panel does not suggest them), and are not normally necessary in other situations. When not in use, they can be stored in their case at the rear of the printer. If you choose to use them, you should place them on the platen when prompted by the front panel (this prompt appears when using the loading accessory). Open the window, place the edge holders, then close the window. WARNING! Do not touch the printer's drying enclosure. Even after you have opened the window latch, which disconnects the power to the drying and curing modules, the internal surfaces could be hot. The edge holders should be placed on the platen so that they slightly overlap the left and right edges of the substrate. The edge holders fit into holes in the platen, and they are magnetic, which helps them to stay in place. 46 Chapter 4 Handle the substrate ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
7.
Press the
OK
button on the front panel.
The front panel displays the amount of printed substrate that is on the take-up reel.
8.
Unlock the take-up reel by lifting both levers.
9.
Remove the roll from the printer, pulling out the end on the right side of the printer first. Do not
insert your fingers into the spindle supports during the removal process.
10.
To remove the roll from the printer after you have unloaded the take-up reel, see
Unload a roll
from the printer
on page
36
.
The edge holders
The edge holders are designed to prevent the edges of the substrate from rising while printing is in
progress. They are recommended for textile and double-sided printing (even if the front panel does not
suggest them), and are not normally necessary in other situations. When not in use, they can be stored
in their case at the rear of the printer.
If you choose to use them, you should place them on the platen when prompted by the front panel (this
prompt appears when using the loading accessory). Open the window, place the edge holders, then
close the window.
WARNING!
Do not touch the printer's drying enclosure. Even after you have opened the window
latch, which disconnects the power to the drying and curing modules, the internal surfaces could be
hot.
The edge holders should be placed on the platen so that they slightly overlap the left and right edges of
the substrate. The edge holders fit into holes in the platen, and they are magnetic, which helps them to
stay in place.
46
Chapter 4
Handle the substrate
ENWW