Home » HP Manuals » Multifunction Devices » HP LaserJet 4345 » Manual Viewer

HP LaserJet 4345 HP LaserJet 4345mfp - User Guide - Page 250

Solving network connectivity problems, Troubleshooting network printing problems

Add to My Manuals
Save this manual to your list of manuals

Page 250 highlights

Solving network connectivity problems If the MFP is having problems communicationg with the network, use the information in this section to resolve the problem. Note Note Troubleshooting network printing problems HP recommends that you use the MFP CD-ROM to install and set up the MFP on a network. ● Make sure that the network cable is securely seated into the MFP's RJ45 connector. ● Make sure that the Link LED on the formatter is lit. See Understanding lights on the formatter. ● Make sure that the I/O card is ready. Print a configuration page (see Checking the MFP configuration). If an HP Jetdirect print server is installed, printing a configuration page also prints a second page that shows the network settings and status. The HP Jetdirect embedded print server supports various network protocols (TCP/IP, IPX/ SPX, Novell/Netware, AppleTalk, and DCL/LLC). Make sure that the correct protocol is enabled for your network. On the HP Jetdirect configuration page, verify the following items for your protocol: - Under HP Jetdirect Configuration, the status is "I/O Card Ready". - The status is "Ready". - An IP address is listed. - The configuration method (Config by:) is listed correctly. See the network administrator if you are not sure which method is correct. ● Try printing the job from another computer. ● To verify that a MFP works with a computer, use a parallel cable to connect it directly to a computer. You will have to reinstall the printing software. Print a document from a program that has printed correctly in the past. If this works, a problem with the network might exist. ● Contact your network administrator for assistance. Verifying communication over the network If the HP Jetdirect configuration page shows an IP address for the MFP, use this procedure to verify that the MFP is communicating with other devices on the network. To verify communication over the network 1. Open a command prompt: a. Windows: Click Start, click Run, and then type cmd. An MS-DOS command prompt opens. 236 Chapter 10 Solving problems ENWW

Section	Page
MFP basics	15
HP LaserJet 4345mfp configurations	16
HP LaserJet 4345mfp (Q3942A—base model)	16
HP LaserJet 4345x mfp (Q3943A)	16
HP LaserJet 4345xs mfp (Q3944A)	16
HP LaserJet 4345xm mfp (Q3945A)	17
Features and benefits of the MFP	18
Functions	18
Speed and throughput	18
Resolution	18
Memory	18
User interface	18
Language and fonts	19
Copying and sending	19
Print cartridge	19
Paper-handling	20
Connectivity	20
Environmental features	20
Security features	20
Minimum system requirements	21
MFP parts and accessories	22
Accessories and supplies	23
Interface ports	24
Moving the MFP	24
Locking and unlocking optional accessories	25
Software	26
Operating systems and MFP components	26
Printer drivers	27
HP disk management utility	31
Software for Macintosh computers	31
Installing the printing system software	31
Uninstalling the software	36
Loading input trays	37
Loading tray 1	37
Loading trays 2, 3, 4 and 5	38
Configuring the trays by using the Paper handling menu	42
Using the control panel	43
Control-panel layout	44
Control-panel features	45
Home-screen navigation	46
Help system	47
\	47
\	47
Menu map	48
Retrieve job menu	49
Information menu	50
Paper handling menu	51
Configure device menu	54
Originals submenu	54
Copying submenu	55
Enhancement submenu	55
Sending submenu	56
Printing submenu	58
PCL submenu	60
Print quality submenu	62
System setup submenu	65
Copy/send settings	69
MBM-3 Configuration submenu	70
Stapler/stacker submenu	70
I/O submenu	71
EIO X Jetdirect submenu	72
Embedded Jetdirect submenu	72
Resets submenu	75
Fax menu	77
Diagnostics menu	78
Service menu	81
Printing	83
Orienting media	84
Printing documents	86
To print a document	86
Selecting which tray is used for printing	87
Understanding tray order	87
Customizing tray 1 operation	87
Printing by type and size of media (locking trays)	88
Manually feeding media from tray 1	89
Selecting the correct fuser mode	90
Selecting the output bin	91
3‑bin mailbox output bins	91
Selecting an output location	91
Selecting face-up or face-down output for copy jobs	92
Printing on envelopes	93
Loading envelopes in tray 1	93
Printing on special media	95
Printing on labels	95
Printing on transparencies	95
Printing on letterhead, prepunched, or preprinted paper	96
Printing on paper that has a special finish	97
Printing on small sizes, custom sizes, or heavy paper	97
Setting custom paper sizes	98
Printing on both sides of paper (optional duplexer)	100
Guidelines for printing on both sides of paper	100
Orientation of paper for duplexing	101
Layout options for printing on both sides of paper	101
To print on both sides by using the optional duplex-printing accessory	102
Setting the registration	103
To set the registration	103
Using features in the printer driver	104
Creating and using quick sets	104
Creating and using watermarks	104
Resizing documents	105
Setting a custom paper size from the printer driver	105
Printing on different paper for the first page of a print job	105
Printing multiple pages on one sheet of paper	106
Setting the stapling options	106
Selecting face-up or face-down output in the printer driver	107
Using job storage features	108
To gain access to the job storage features	108
Printing a private job	108
Deleting a private job	109
Storing a print job	109
Creating a QuickCopying job	110
Printing additional copies of QuickCopy jobs	110
Deleting a QuickCopy job	111
Proofing and holding a job	111
Printing the remaining copies of a held job	111
Deleting a held job	112
Copying	113
Copy-screen navigation	114
Cancel button	114
OK button	114
Basic copying instructions	115
Copying by using the default settings	115
Copying by using user-defined settings	115
Copying by using the scanner glass	117
Copying by using the ADF	117
Using Job Mode	117
Modifying copy settings for the current job	118
Adjusting the copy contrast	118
Reducing or enlarging copies	118
Background removal	118
Sharpness	118
Contrast	118
Copying multiple sized originals	119
Creating a stored copy job	119
Scanning and sending to e‑mail	121
What is SMTP?	122
What is LDAP?	122
E‑mail configuration	123
Automatic e‑mail configuration	123
Manual e-mail configuration	123
To find gateways by using an e‑mail program	124
E‑mail screen navigation	125
Help button	125
From: field	125
To:, CC:, and BCC: fields	125
Clear All button	125
E‑mail basics	126
Loading documents	126
Sending documents	126
Using the address book	128
Creating a recipient list	128
Using the local address book	128
Additional e‑mail features	130
Secondary e‑mail	130
Send to folder	130
Send to workflow	130
Faxing	131
Analog faxing	132
Installing the fax accessory	132
Connecting the fax accessory to a phone line	134
Configuring and using the fax features	135
Digital faxing	136
Optional output and input devices	137
3‑bin mailbox	138
Mailbox mode	138
Stacker mode	138
Function-separator mode	138
Using the 3‑bin mailbox	138
Stapler/stacker accessory	141
To configure the printer driver to recognize the optional stapler/stacker	141
To select the stapler in the software (Windows)	141
To select the stapler in the software (Mac)	141
To select the stapler at the control panel for printed jobs	142
To select the stapler in the printer driver for printed jobs (Windows)	142
To select the stapler in the printer driver for printed jobs (Mac)	142
To set the stapler at the control panel for all copy jobs	142
To set the stapler at the control panel for a single copy job	143
To configure the MFP to stop or continue when the staple cartridge is empty	143
Loading staples	143
500-sheet feeders and the cabinet/stand	145
Envelope feeder	146
Installing the optional envelope feeder	146
Removing the optional envelope feeder	147
Loading envelopes in the optional envelope feeder	147
Troubleshooting the output and input accessories	150
Security features	151
Securing the embedded Web server	152
To secure the embedded Web server	152
Foreign Interface Harness (FIH)	153
Requirements	153
Using the FIH	153
Secure Disk Erase	155
Data affected	155
Gaining access to Secure Disk Erase	155
Additional Information	155
Job-storage features	156
DSS authentication	157
Locking the control‑panel menus	158
To lock the control‑panel menus	158
Locking the formatter cage	159
Managing and maintaining the MFP	161
Using the embedded Web server	162
Opening the embedded Web server	162
Information tab	163
Settings tab	163
Digital Sending tab	164
Networking tab	164
Other links	165
Using the HP Toolbox	166
Supported operating systems	166
Supported browsers	166
To view the HP Toolbox	167
Status tab	167
Alerts tab	167
Device Settings window	168
Toolbox links	168
Other links	168
Using HP Web Jetadmin software	169
Configuring and verifying an IP address	170
TCP/IP assignment	170
Verifying the TCP/IP configuration	170
Changing an IP address	170
Setting the real-time clock	172
Setting the date and time	172
Setting the wake time	173
Setting the sleep delay	174
Checking the MFP configuration	175
To print an information page	175
Menu map	175
Configuration page	175
HP Jetdirect page	177
Supplies status page	177
Usage page	178
PCL or PS font list	179
Managing the print cartridge	180
HP print cartridges	180
Non-HP print cartridges	180
Print-cartridge authentication	180
Print-cartridge storage	180
Print-cartridge life expectancy	180
Checking the supply level	181
Cartridge-low and cartridge-out conditions	181
Upgrading the firmware	183
Determining the current level of firmware	183
Downloading the new firmware from the HP Web site	183
Transferring the new firmware to the MFP	183
Upgrading the HP Jetdirect firmware	185
Cleaning the MFP	187
Cleaning the outside of the MFP	187
Cleaning the touchscreen	187
To clean the scanner glass	187
Cleaning the fuser	187
Cleaning the ADF delivery system	188
Calibrating the scanner	192
To print the calibration target	192
Performing preventive maintenance	193
Printer preventive maintenance	193
The ADF maintenance kit	193
Solving problems	195
Solving general problems	196
Troubleshooting checklist	196
Determining MFP problems	198
Clearing jams	199
Clearing jams from the top-cover and print-cartridge areas	200
Clearing jams from the optional envelope-feeder area	202
Clearing jams from the tray 1 area	203
Clearing jams from the tray 2, 3, 4, or 5 areas	205
Clearing jams from the optional duplexer	206
Clearing jams from the output areas	207
Clearing jams from the fuser	209
Clearing jams from the ADF	212
Clearing staple jams	213
Solving repeated jams	215
Using the paper-path test	215
Understanding MFP messages	217
Using the MFP help system	217
If a message persists	217
Resolving control‑panel messages	218
Understanding accessory lights for the 3‑bin mailbox and stapler/stacker	230
Accessory lights	230
Replacing accessories or accessory components	231
Understanding lights on the formatter	232
HP Jetdirect LEDs	232
Heartbeat LED	232
Fax LED	233
Correcting print-quality and copy-quality problems	234
Print-quality checklist	234
Image defect examples	234
Light print (partial page)	236
Light print (entire page)	237
Specks	237
Dropouts	237
Lines	238
Gray background	238
Toner smear	239
Loose toner	239
Repeating defects	240
Repeating image	240
Misformed characters	241
Page skew	241
Curl or wave	241
Wrinkles or creases	242
Vertical white lines	242
Tire tracks	243
White spots on black	243
Scattered lines	243
Blurred print	244
Random image repetition	244
Blank page (ADF)	245
Horizontal lines (ADF)	245
Page skew (ADF)	246
Vertical lines (ADF)	246
Image shifted (ADF)	246
Unexpected image (ADF)	247
Repetitive defect ruler	248
Solving e‑mail problems	249
To validate the SMTP gateway address	249
To validate the LDAP gateway address	249
Solving network connectivity problems	250
Troubleshooting network printing problems	250
Verifying communication over the network	250
Supplies and accessories	253
Ordering parts, accessories, and supplies	254
Ordering directly from HP	254
Ordering through service or support providers	254
Ordering directly through the embedded Web server (for printers that are connected to a network)	254
Ordering directly through the HP Toolbox software (for printers that are directly connected to a com ...	254
Part numbers	255
Accessories	255
Print cartridges	255
Maintenance kits	256
Memory	256
Cables and interfaces	257
Print media	257
Service and support	261
Hewlett-Packard limited warranty statement	261
Print Cartridge Limited Warranty Statement	262
Availability of support and service	263
HP maintenance agreements	263
Priority Onsite Service	263
Next business day	263
Installation and maintenance-kit replacement	263
Repacking the MFP	264
To repack the MFP	264
Service information form	265
MFP specifications	267
Physical specifications	268
Electrical specifications	269
Acoustic specifications	270
Environmental specifications	271
Image area	272
Skew specifications	273
Media specifications	275
Print media specifications	275
Printing and paper storage environment	275
Envelopes	276
Labels	278
Transparencies	278
Supported types and sizes of print media	279
MFP memory and expansion	285
Memory overview	286
Determining memory requirements	287
Installing memory	288
To install memory DIMMs	288
To install a flash memory card	290
Replacing the hard-disk drive	292
Checking memory installation	296
To verify that memory devices are installed correctly	296
Saving resources (permanent resources)	297
Installing EIO cards	298
To install EIO cards	298
Regulatory information	299
Introduction	299
FCC regulations	300
Telecom	301
Environmental Product Stewardship program	302
Protecting the environment	302
Ozone production	302
Energy consumption	302
HP LaserJet printing supplies	303
Material safety data sheet	304
For more information	304
Declaration of conformity (HP LaserJet 4345mfp)	305
Declaration of conformity (HP LaserJet 4345x mfp, 4345xs mfp, and 4345xs mfp)	306
Country-/region-specific safety statements	307
Laser safety statement	307
Canadian DOC statement	307
Japanese VCCI statement	307
Korean EMI statement	307
Finnish laser statement	308
Australia	308

Match case Limit results 1 per page

Solving network connectivity problems

If the MFP is having problems communicationg with the network, use the information in this

section to resolve the problem.

Troubleshooting network printing problems

Note

HP recommends that you use the MFP CD-ROM to install and set up the MFP on a network.

●

Make sure that the network cable is securely seated into the MFP's RJ45 connector.

●

Make sure that the Link LED on the formatter is lit. See

Understanding

lights

the

formatter

●

Make sure that the I/O card is ready. Print a configuration page (see

Checking

the

MFP

configuration

). If an HP Jetdirect print server is installed, printing a configuration page

also prints a second page that shows the network settings and status.

Note

The HP Jetdirect embedded print server supports various network protocols (TCP/IP, IPX/

SPX, Novell/Netware, AppleTalk, and DCL/LLC). Make sure that the correct protocol is

enabled for your network.

On the HP Jetdirect configuration page, verify the following items for your protocol:

–

Under HP Jetdirect Configuration, the status is "I/O Card Ready".

–

The status is "Ready".

–

An IP address is listed.

–

The configuration method (Config by:) is listed correctly. See the network

administrator if you are not sure which method is correct.

●

Try printing the job from another computer.

●

To verify that a MFP works with a computer, use a parallel cable to connect it directly to

a computer. You will have to reinstall the printing software. Print a document from a

program that has printed correctly in the past. If this works, a problem with the network

might exist.

●

Contact your network administrator for assistance.

Verifying communication over the network

If the HP Jetdirect configuration page shows an IP address for the MFP, use this procedure

to verify that the MFP is communicating with other devices on the network.

To verify communication over the network

Open a command prompt:

Windows

: Click

Start

, click

Run

, and then type

cmd

. An MS-DOS command prompt

opens.

236

Chapter 10

Solving problems

ENWW