HP MSA 1040 HP MSA 1040 SMU Reference Guide (762784-001, March 2014) - Page 161

ftp 10.1.0.9, flash, put T230R01-01.bin flash

Get HP MSA 1040 PDF manuals and user guides View all HP MSA 1040 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 161 highlights

6. Enter: ftp controller-network-address For example: ftp 10.1.0.9 7. Log in as an FTP user. 8. Enter: put firmware-file flash For example: put T230R01-01.bin flash CAUTION: Do not perform a power cycle or controller restart during a firmware update. If the update is interrupted or there is a power failure, the module might become inoperative. If this occurs, contact technical support. The module might need to be returned to the factory for reprogramming. NOTE: If you attempt to load an incompatible firmware version, the message *** Code Load Fail. Bad format image. *** is displayed and after a few seconds the FTP prompt is redisplayed. The code is not loaded. Firmware update typically takes 10 minutes for a controller having current CPLD firmware, or 20 minutes for a controller with downlevel CPLD firmware. If the controller enclosure has attached enclosures, allow additional time for each expansion module's enclosure management processor (EMP) to be updated. This typically takes 2.5 minutes for each EMP in an MSA 1040 or P2000 drive enclosure. EMPs in D2700 drive enclosures must be updated separately. NOTE: If you are using a Windows FTP client, during firmware update a client-side FTP application issue can cause the FTP session to be aborted. If this issue persists try using SMU to perform the update, use another client, or use another FTP application. If the Storage Controller cannot be updated, the update operation is cancelled. If the FTP prompt does not return, quit the FTP session and log in again. Verify that you specified the correct firmware file and repeat the update. If this problem persists, contact technical support. When firmware update on the local controller is complete, the message Operation Complete is printed, the FTP session returns to the ftp> prompt, and the FTP session to the local MC is closed. If PFU is enabled, allow an additional 10-20 minutes for the partner controller to be updated. 9. Quit the FTP session. 10. Clear your web browser's cache, then sign in to SMU. If PFU is running on the controller you sign in to, a dialog box shows PFU progress and prevents you from performing other tasks until PFU is complete. NOTE: After firmware update has completed on both controllers, if the system health is Degraded and the health reason indicates that the firmware version is incorrect, verify that you specified the correct firmware file and repeat the update. If this problem persists, contact technical support. Updating firmware 161

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
Updating firmware
161
6.
Enter:
ftp
controller-network-address
For example:
ftp 10.1.0.9
7.
Log in as an FTP user.
8.
Enter:
put
firmware-file
flash
For example:
put T230R01-01.bin flash
CAUTION:
Do not perform a power cycle or controller restart during a firmware update. If the update is
interrupted or there is a power failure, the module might become inoperative. If this occurs, contact technical
support. The module might need to be returned to the factory for reprogramming.
NOTE:
If you attempt to load an incompatible firmware version, the message
*** Code Load Fail.
Bad format image. ***
is displayed and after a few seconds the FTP prompt is redisplayed. The code
is not loaded.
Firmware update typically takes 10 minutes for a controller having current CPLD firmware, or 20 minutes for a
controller with downlevel CPLD firmware. If the controller enclosure has attached enclosures, allow additional time
for each expansion module’s enclosure management processor (EMP) to be updated. This typically takes 2.5
minutes for each EMP in an MSA 1040 or P2000 drive enclosure. EMPs in D2700 drive enclosures must be
updated separately.
NOTE:
If you are using a Windows FTP client, during firmware update a client-side FTP application issue can
cause the FTP session to be aborted. If this issue persists try using SMU to perform the update, use another
client, or use another FTP application.
If the Storage Controller cannot be updated, the update operation is cancelled. If the FTP prompt does not return,
quit the FTP session and log in again. Verify that you specified the correct firmware file and repeat the update. If
this problem persists, contact technical support.
When firmware update on the local controller is complete, the message
Operation Complete
is printed, the
FTP session returns to the
ftp>
prompt, and the FTP session to the local MC is closed.
If PFU is enabled, allow an additional 10–20 minutes for the partner controller to be updated.
9.
Quit the FTP session.
10.
Clear your web browser’s cache, then sign in to SMU. If PFU is running on the controller you sign in to, a dialog
box shows PFU progress and prevents you from performing other tasks until PFU is complete.
NOTE:
After firmware update has completed on both controllers, if the system health is Degraded and the
health reason indicates that the firmware version is incorrect, verify that you specified the correct firmware file
and repeat the update. If this problem persists, contact technical support.