Yamaha 01V96 Owner's Manual - Page 283

Appendix B: Specifications General Spec 283 General Spec Number of scene memories 99 Sampling Frequency Signal Delay Internal External fs=48 kHz fs=96 kHz 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz Normal rate: 44.1 kHz-10% to 48 kHz+6% Double rate: 88.2 kHz-10% to 96 kHz+6% Less than 1.6 ms CH INPUT to STEREO OUT Less than 0.8 ms CH INPUT to STEREO OUT Fader 100 mm motorized × 17 Fader Resolution Total Harmonic Distortion1 (CH INPUT to STEREO OUT) (Input Gain=Min.) fs=48 kHz fs=96 kHz Frequency Response (CH INPUT to STEREO OUT) fs=48 kHz fs=96 kHz +10 to -138, -∞ dB input faders 0 to -138, -∞ dB master faders, stereo fader Less than 0.05% 20 Hz-20 kHz @ +14 dB into 600 Ω Less than 0.01% 1 kHz @ +24 dB into 600 Ω Less than 0.05% 20 Hz-40 kHz @ +14 dB into 600 Ω Less than 0.01% 1 kHz @ +24 dB into 600 Ω 20 Hz-20 kHz, 0.5, -1.5 dB @ +4 dB into 600 Ω 20 Hz-40 kHz, 0.5, -1.5 dB @ +4 dB into 600 Ω Dynamic Range (maximum level to noise level) 110 dB typ. DA Converter (STEREO OUT) 105 dB typ. AD+DA (to STEREO OUT) @ fs=48 kHz 105 dB typ. AD+DA (to STEREO OUT) @ fs=96 kHz -128 dB Equivalent Input Noise Hum & Noise2 (20 Hz-20 kHz) Rs=150 Ω -86 dB residual output noise. STEREO OUT (STEREO OUT off) Input Gain=Max. -86 dB (90 dB S/N) STEREO OUT Input Pad =0 dB (STEREO fader at nominal level and all CH INPUT faders at minimum level) Input Pad =0 dB Input Sensitivity -64 dB (68 dB S/N) STEREO OUT =-60 dB (STEREO fader at nominal level and one CH INPUT fader at nominal level) Maximum Voltage Gain Crosstalk (@ 1 kHz) Input Gain=Min. Phantom switch 74 dB CH INPUT (CH1-12) to STEREO OUT/OMNI (BUS) OUT 40 dB CH INPUT (CH13-16) to STEREO OUT 74 dB CH INPUT (CH1-12) to OMNI (AUX) OUT (via pre input fader) 74 dB CH INPUT (CH1-12) to MONITOR OUT (via STEREO BUS) 80 dB adjacent input channels (CH1-12) 80 dB adjacent input channels (CH13-16) 80 dB input to output +48 V DC (each 4ch) Pad switch 0/20 dB attenuation Gain control 44 dB (-60 to -16), detented AD Input (1-12) Peak indicator Signal indicator AD converter Gain control LED (red) turns on when post HA level reaches 3 dB below clipping at digital domain LED (green) turns on when post HA level reaches 20 dB below nominal at digital domain 24-bit linear, 128-times oversampling (fs=44.1, 48 kHz), 64-times oversampling (fs=88.2, 96 kHz) 30 dB (-26 to +4), detented AD Input (13-16) Peak indicator Signal indicator AD converter Input selector LED (red) turns on when post HA level reaches 3 dB below clipping at digital domain LED (green) turns on when post HA level reaches 20 dB below nominal at digital domain 24-bit linear, 128-times oversampling (fs=44.1, 48 kHz), 64-times oversampling (fs=88.2, 96 kHz) CH15/16/2TR IN for CH15/16 01V96-Owner's Manual