Yamaha 01V96 Owner's Manual - Page 289

Analog Input Spec 289 Analog Input Spec Input PAD GAIN Actual Load Impedance For Use With Nominal Sensitivity1 Input level Nominal Max. before clip Connector INPUT A/B 1-12 INPUT 13-16 CH INSERT IN 1-12 2TR IN [L, R] -60 dB 0 -16 dB 20 -26 dB - +4 dB - - 3k Ω 10k Ω 10k Ω 10k Ω 50-600 Ω Mics & 600 Ω Lines 600 Ω Lines 600 Ω Lines 600 Ω Lines -70 dB (0.245 mV) -26 dB (38.8 mV) -6 dB (338 mV) -36 dB (12.3 mV) -6 dB (388 mV) -12 dB (195 mV) -10 dBV (316 mV) -60 dB (0.775 mV) -16 dB (123 mV) +4 dB (1.23 V) -26 dB (38.8 mV) +4 dB (1.23 V) -2 dB (616 mV) -10 dBV (316 mV) -40 dB (7.75 mV) +4 dB (1.23 V) +24 dB (12.28 V) -6 dB (388 mV) +24 dB (12.28 V) +18 dB (6.16 V) +10 dBV (3.16 V) A: XLR-3-31 type (Balanced)2 B: Phone jack (TRS) (Balanced)3 Phone jack (TRS) (Balanced)3 Phone jack (TRS) (Unbalanced)4 RCA pin jack (Unbalanced) 1. Sensitivity is the lowest level that will produce an output of +4 dB (1.23 V) or the nominal output level when the unit is set to maximum gain. (All faders and level controls are maximum position.) 2. XLR-3-31 type connectors are balanced (1=GND, 2=HOT, 3=COLD). 3. Phone jacks are balanced (Tip=HOT, Ring=COLD, Sleeve=GND). 4. CH INSERT IN/OUT phone jacks are unbalanced. (Tip=OUTPUT, Ring=INPUT, Sleeve=GND). In these specifications, when dB represents a specific voltage, 0 dB is referenced to 0.775 Vrms. For 2TR IN levels, 0 dBV is referenced to 1.00 Vrms. All input AD converters (CH INPUT 1-16) are 24-bit linear, 128-times oversampling. (@fs=44.1, 48 kHz) +48 V DC (phantom power) is supplied to CH INPUT (1-12) XLR type connectors. Three PHANTOM +48V switches CH1-4, 5-8, 9-12 turn on the phantom power for inputs 1-4, 5-8, 9-12 respectively. Analog Output Specs Output Actual Source Impedance For Use With Nominal Output level Nominal Max. before clip Connector STEREO OUT [L, R] OMNI OUT 1-4 MONITOR OUT [L, R] CH INSERT OUT 1-12 2TR OUT [L, R] PHONES 150 Ω 150 Ω 150 Ω 600 Ω 600 Ω 100 Ω 600 Ω Lines 10k Ω Lines 10k Ω Lines 10k Ω Lines 10k Ω Lines 8 Ω Phones 40 Ω Phones +4 dB (1.23 V) +4 dB (1.23 V) +4 dB (1.23 V) -2 dB (616 mV) -10 dBV (316 mV) 4 mW 12 mW +24 dB (12.28 V) +24 dB (12.28 V) +24 dB (12.28 V) +18 dB (6.16 V) +10 dBV (3.16 V) 25 mW 75 mW XLR-3-32 type (Balanced)1 Phone jack (TRS) (Balanced)2 Phone jack (TRS) (Balanced)2 Phone jack (TRS) (Unbalanced)3 RCA Pin Jack (Unbalanced) Stereo Phone Jack (TRS) (Unbalanced)4 1. XLR-3-32 type connectors are balanced (1=GND, 2=HOT, 3=COLD). 2. Phone jacks are balanced (Tip=HOT, Ring=COLD, Sleeve=GND). 3. CH INSERT IN/OUT phone jacks are unbalanced. (Tip=OUTPUT, Ring=INPUT, Sleeve=GND). 4. PHONES stereo phone jack is unbalanced (Tip=LEFT, Ring=RIGHT, Sleeve=GND). In these specifications, when dB represents a specific voltage, 0 dB is referenced to 0.775 Vrms. 2TR OUT [L, R] levels, 0 dBV is referenced to 1.00 Vrms. All output DA converters are 24-bit, 128-times oversampling. (@fs=44.1, 48 kHz) 01V96-Owner's Manual