HP OmniBook 500 hp omnibook 500 - Corporate Evaluator's Guide - Page 129

To install video support, Highlight the CMD PCI 646U2/648/649 Ultra DMA IDE Controller and click OK.

Page 129 highlights

Using Windows NT 4.0 Installing Windows NT 4.0 3. Click "Have Disk". 4. Insert the floppy disk with the CMD drivers copied to it. Browse the floppy drive, double-click the WINNT directory, double-click OEMSETUP.INF file. 5. Click OK to install from disk. 6. Highlight the "CMD PCI 646U2/648/649 Ultra DMA IDE Controller" and click OK. 7. When prompted to reboot, you must reboot for the new changes to take effect. 8. Your system and CMD IDE controller should work properly. (If the system fails with a blue screen with the third line from top say "Inaccessible_boot_device," then CMD driver is not loaded properly in previous steps. Go back to step 1 and follow the procedure again.) To install video support If you have installed retail Windows you need to install the video driver. The video driver is in the \HP\DRIVERS\NT4\VIDEO subdirectory. To install or upgrade the video driver: 1. Run SETUP.EXE from the \HP\DRIVERS\NT4\VIDEO directory. 2. Follow the instructions on the screen to install the video driver. 3. Click Finish to restart your computer. The driver will be installed after the system reboots. If your operating system asks you for settings, set the resolution to 1024 x 768, and the Color Palette to 65536 colors. Upon successful installation, an ATI icon appears on the bottom right corner of the taskbar. To install audio support If you have installed retail Windows NT4 you need to install the audio driver. The audio driver is in the \HP\DRIVERS\NT4\AUDIO subdirectory. To install or upgrade the audio driver: 1. Run SETUP.EXE from the \HP\DRIVERS\NT4\AUDIO directory. Corporate Evaluator's Guide 129

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199

Using Windows NT 4.0
Installing Windows NT 4.0
Corporate Evaluator’s Guide
129
3. Click “Have Disk”.
4.
Insert the floppy disk with the CMD drivers copied to it. Browse the floppy drive,
double-click the WINNT directory, double-click OEMSETUP.INF file.
5. Click OK to install from disk.
6.
Highlight the “CMD PCI 646U2/648/649 Ultra DMA IDE Controller” and click OK.
7.
When prompted to reboot, you must reboot for the new changes to take effect.
8.
Your system and CMD IDE controller should work properly. (If the system fails with
a blue screen with the third line from top say “Inaccessible_boot_device,” then CMD
driver is not loaded properly in previous steps.
Go back to step 1 and follow the
procedure again.)
To install video support
If you have installed retail Windows you need to install the video driver.
The video
driver is in the \HP\DRIVERS\NT4\VIDEO subdirectory.
To install or upgrade the video driver:
1. Run SETUP.EXE from the \HP\DRIVERS\NT4\VIDEO directory.
2.
Follow the instructions on the screen to install the video driver.
3. Click Finish to restart your computer.
The driver will be installed after the system reboots.
If your operating system asks you for settings, set the resolution to 1024 x 768, and the
Color Palette to 65536 colors.
Upon successful installation, an ATI icon appears on the bottom right corner of the
taskbar.
To install audio support
If you have installed retail Windows NT4 you need to install the audio driver.
The audio
driver is in the \HP\DRIVERS\NT4\AUDIO subdirectory.
To install or upgrade the audio driver:
1. Run SETUP.EXE from the \HP\DRIVERS\NT4\AUDIO directory.