HP StorageWorks 1606 Brocade Fabric OS Command Reference v6.3.0 (53-1001337-01 - Page 446

2 ipsecConfig 4. Configure the SA proposal lifetime in seconds. switch:admin> ipsecconfig --add policy ips sa-proposal -t IPSEC-ESP -lttime 280000 -sa ESP01 5. Import the public key for the BROCADE300 (Brocade300.pem), the private key for BROCADE300 (Brocade300-key.pem), and the public key of the external host (remote-peer.pem) in X.509 PEM format from the remote certificate server (10.6.103.139). switch:admin> seccertutil import -ipaddr 10.103.6.139 -remotedir /root/certs -certname \ Brocade300.pem switch:admin> seccertutil import -ipaddr 10.103.6.139 -remotedir /root/certs -certname \ Brocade300-key.pem switch:admin> seccertutil import -ipaddr 10.103.6.139 -remotedir /root/certs -certname \ remote-peer.pem 6. Import the CA certificate that was used to sign the public certificates of BROCADE300 and the remote peer as IPSECCA.pem. switch:admin> seccertutil import -ipaddr 10.103.6.139 -remotedir /root/certs \ -certname IPSECCA.pem 7. Configure an IKE policy for the remote peer UNIX host. switch:admin> ipsecconfig --add policy ike -t IKE01 -remote fe80::205:1fff:fe51:f09e \ -id fe80::220:1aff:fe34:2e82 -remoteid fe80::205:1fff:fe51:f09e \ -enc 3des_cbc -hash hmac_md5 -prf hmac_md5 -auth rsasig -dh modp1024 \ -pubkey "Brocade300.pem" -privkey "Brocade300-key.pem" -peerpubkey "remote-peer.pem" 8. Create an IPsec transform TRANSFORM01 to use transport mode to protect traffic identified for IPsec protection and use IKE01 as the key management policy. switch:admin> ipsecconfig --add policy ips transform -t TRANSFORM01 \ -mode transport -sa-proposal IPSEC-ESP -action protect -ike IKE01 9. Create traffic selectors to select outbound and inbound TCP traffic that needs to be protected. switch:admin> ipsecconfig --add policy ips selector -t SELECTOR-OUT \ -d out -l fe80::220:1aff:fe34:2e82 -r fe80::205:1fff:fe51:f09e \ -protocol "tcp" -transform TRANSFORM01 switch:admin> ipsecconfig --add policy ips selector -t SELECTOR-IN \ -d in -l fe80::205:1fff:fe51:f09e -r fe80::220:1aff:fe34:2e82 \ -protocol "tcp" -t transform TRANSFORM01 10. Verify the IPSec SAs using ipSecConfig --show manual-sa -a. Refer to the "IPsec display commands" section for an example. 11. Perform the equivalent steps on the remote peer to complete the IPsec configuration. Refer to your server administration guide for instructions. Example 3 Secure traffic between two systems using AH with SHA1 and ESP protection with 3DES and configure IKE with pre-shared keys. The two systems are a switch, BROCADE300 (IP address 10.33.74.13), and an external UNIX host (IPv4 address 10.33.69.132). 1. On the system console, log into the switch as Admin and enable IPsec. switch:admin> ipsecconfig --enable 2. Create an IPsec SA policy named AH01, which uses AH protection with SHA1. switch:admin> ipsecconfig --add policy ips sa -t AH01 -p ah -auth hmac_sha1 416 Fabric OS Command Reference 53-1001337-01