Kyocera KM-5530 KM/Ri 4530/5530 Operation Guide Rev 5F - Page 106

Section 5 OTHER CONVENIENT FUNCTIONS 3 Selecting between 1-sided or 2-sided copies This procedure selects the type of finished copies to be made between 1-sided and 2-sided. 1 With the content of the "Basic" tab displayed, touch the "1 sided/2 sided" key. The "1 sided/2 sided" screen will be displayed. Inch specifications Ready to Job build. Place originals then press Start key. Job Build - Step1 11x81/2" Select paper None Finished Basic 1-sided Original type AMS Reduce /Enlarge Quality 1 sided copy 1 sided/ 2 sided Back Edge Orig. set direction Edit 1 sided copy-Left Finished page #:0 Set End Insert page Metric specifications Ready to Job build. Set original. Press Start key. Job Build-Step 1 Select paper None Finished Basic 1-sided Original type AMS Reduce/ Enlarge Quality 1-sided Copy 1-sided/ 2-sided Back Edge Orig. set direction Edit 1-sided Copy-Left Finished page #: 0 Set End Insert blank page NOTE The setting in regard to making either 1-sided or 2-sided copies can only be made in the first step of the job build mode and will apply to all steps in the copy job. 2 Touch the "1 sided" key or the "2 sided" key, as appropriate, and then select the binding direction you want for the finished copies. Follow the instructions on the right side of the touch panel and verify the direction in which the originals were set. Inch specifications Ready to Job build. Place originals then press Start key. 1 sided/ 2 sided copy Finished 1 sided copy 2 sided copy Open from left Open from right Open from top Set Back Close Check direction Check direction of original top side. Rear Left top corner Metric specifications Ready to Job build. Set original. Press Start key. 1-sided / 2-sided Copy Finished 1-sided Copy 2-sided Copy Left binding Right binding Top binding Set Back Close Check direction Check direction of original. Back Edge Left top corner IMPORTANT! If the designation for the direction that the originals are set is not correct, copying may be accomplished incorrectly. 3 Touch the "Close" key. The touch panel will return to the screen in step 1. 4 Selecting how to finished up the copy sets If the optional Document Finisher is installed on your copier, this procedure lets you select whether to staple or hole punch the finished copy sets. 1 With the content of the "Basic" tab displayed, touch the "Finished" key. The "Finished" screen will be displayed. Inch specifications Ready to Job build. Place originals then press Start key. Job Build - Step1 11x81/2" Select paper None Finished Basic 1-sided Original type AMS Reduce /Enlarge Quality 1 sided copy 1 sided/ 2 sided Back Edge Orig. set direction Edit 1 sided copy-Left Finished page #:0 Set End Insert page Metric specifications Ready to Job build. Set original. Press Start key. Job Build-Step 1 Select paper None Finished Basic 1-sided Original type AMS Reduce/ Enlarge Quality 1-sided Copy 1-sided/ 2-sided Back Edge Orig. set direction Edit 1-sided Copy-Left Finished page #: 0 Set End Insert blank page NOTE The setting in regard to how the copy sets will be finished can only be made in the first step of the job build mode and will apply to all steps in the copy job. 2 Select how you want the copy sets to be finished by touching the "Staple mode" key, the "Saddle Stitch" ["Center Staple" ] key or the "Punch mode" key, as appropriate. Follow the instructions on the right side of the touch panel and verify the direction in which the originals were set. Inch specifications Ready to Job build. Place originals then press Start key. Finished Sorting Staple None 1 set No cover Staple mode Saddle Stitch Punch No cover Punch mode Set Back Close Check direction Check direction of original top side. Rear Left top corner Metric specifications Ready to Job build. Set original. Press Start key. Finished Group None 1 set Group None 1 set Staple None Staple Mode Center Staple Punch None Punch Mode Set Back Close Check direction Check direction of original. Back Edge Left top corner 5-64