Canon XF605 Instruction Manual - Page 86

Selecting Drop or Non-Drop Frame, elect, etup] > [Time Code DF/NDF] > De, ired option.

Page 86 highlights

Setting the Time Code Selecting Drop or Non-Drop Frame When the frame rate is set to 59.94P, 59.94i or 29.97P, you can select between a drop frame (DF) or non-drop frame (NDF) time code, depending on how you plan to use your recordings. 86 With all other frame rates, the time code is set to non-drop frame (NDF) and cannot be changed. Select > [B System Setup] > [Time Code DF/NDF] > Desired option. • The time code display will change depending on the setting. When you select [DF], the time code will appear as [00:00:00.00]; when you select [NDF], it will appear as [00:00:00:00]. About the time code display A letter may appear next to the time code depending on the setting/status. Refer to the following table. Letter Description R The time code mode is set to [Regen.]. P The time code mode is set to [Preset] and the running mode is set to [Rec Run]. F The time code mode is set to [Preset] and the running mode is set to [Free Run]. E The time code signal is coming from an external source. No letter Time code during clip playback. NOTES • The frames value of the time code runs from 0 to 23 (frame rate set to 23.98P), from 0 to 24 (frame rate set to 25.00P, 50.00i or 50.00P), or from 0 to 29 (all other frame rates). • When slow & fast motion recording, frame recording or interval recording are activated, you cannot select the [Free Run] running mode. Conversely, when pre-recording is activated, [Free Run] is set automatically and cannot be changed. • When slow & fast motion recording, frame recording or interval recording are activated, the time code signal will not be output from any of the terminals. • When you mix drop frame and non-drop frame time codes, there might be a discontinuity in the time code at the point where the recording starts. • When you are using the [Free Run] running mode, the time code will continue running as long as the built-in backup battery has some charge left, even if you disconnect all other power sources. • If you set an assignable button to [Time Code] (A 115), you can press the button to open the [B System Setup] menu page with the time code settings.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238

S
etting the Time Code
86
Selecting Drop or Non-Drop Frame
When the frame rate is set to 59.94P, 59.94i or 29.97P, you can select between a drop frame (DF) or non-drop
frame (NDF) time code, depending on how you plan to use your recordings.
With all other frame rates, the time code is set to non-drop frame (NDF) and cannot be changed.
S
elect
> [
B
S
y
s
tem
S
etup] > [Time Code DF/NDF] > De
s
ired option.
The time code display will change depending on the setting. When you select [DF], the time code will appear
as [00:00:00.00]; when you select [NDF], it will appear as [00:00:00:00].
About the time code di
s
play
A letter may appear next to the time code depending on the setting/status. Refer to the following table.
NOTES
NOTES
The frames value of the time code runs from 0 to 23 (frame rate set to 23.98P), from 0 to 24 (frame rate set to
25.00P, 50.00i or 50.00P), or from 0 to 29 (all other frame rates).
When slow & fast motion recording, frame recording or interval recording are activated, you cannot select the
[Free Run] running mode. Conversely, when pre-recording is activated, [Free Run] is set automatically and
cannot be changed.
When slow & fast motion recording, frame recording or interval recording are activated, the time code signal
will not be output from any of the terminals.
When you mix drop frame and non-drop frame time codes, there might be a discontinuity in the time code at
the point where the recording starts.
When you are using the [Free Run] running mode, the time code will continue running as long as the built-in
backup battery has some charge left, even if you disconnect all other power sources.
If you set an assignable button to [Time Code] (
A
115), you can press the button to open the
[
B
System Setup] menu page with the time code settings.
Letter
Description
R
The time code mode is set to [Regen.].
P
The time code mode is set to [Preset] and the running mode is set to [Rec Run].
F
The time code mode is set to [Preset] and the running mode is set to [Free Run].
E
The time code signal is coming from an external source.
No letter
Time code during clip playback.