HP 6125G HP 6125G & 6125G/XG Blade Switches High Availability Configur - Page 71
Enable RRPP., Con Device B as the transit node of primary ring 1
View all HP 6125G manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 71 highlights
[DeviceA] rrpp domain 1 [DeviceA-rrpp-domain1] control-vlan 4092 [DeviceA-rrpp-domain1] protected-vlan reference-instance 1 # Configure Device A as the master node of primary ring 1, with GigabitEthernet 1/0/1 as the primary port and GigabitEthernet 1/0/2 as the secondary port, and enable ring 1. [DeviceA-rrpp-domain1] ring 1 node-mode master primary-port gigabitethernet 1/0/1 secondary-port gigabitethernet 1/0/2 level 0 [DeviceA-rrpp-domain1] ring 1 enable [DeviceA-rrpp-domain1] quit # Enable RRPP. [DeviceA] rrpp enable 2. Configure Device B: # Create VLANs 1 through 30, map these VLANs to MSTI 1, and activate the MST region configuration. system-view [DeviceB] vlan 1 to 30 [DeviceB] stp region-configuration [DeviceB-mst-region] instance 1 vlan 1 to 30 [DeviceB-mst-region] active region-configuration [DeviceB-mst-region] quit # Cancel the physical state change suppression interval setting on GigabitEthernet 1/0/1 and GigabitEthernet 1/0/2, disable the spanning tree feature, and set the trusted packet priority type to 802.1p priority. Configure the two ports as trunk ports, and assign them to VLANs 1 through 30. [DeviceB] interface gigabitethernet 1/0/1 [DeviceB-GigabitEthernet1/0/1] undo link-delay [DeviceB-GigabitEthernet1/0/1] undo stp enable [DeviceB-GigabitEthernet1/0/1] qos trust dot1p [DeviceB-GigabitEthernet1/0/1] port link-type trunk [DeviceB-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30 [DeviceB-GigabitEthernet1/0/1] quit [DeviceB] interface gigabitethernet 1/0/2 [DeviceB-GigabitEthernet1/0/2] undo link-delay [DeviceB-GigabitEthernet1/0/2] undo stp enable [DeviceB-GigabitEthernet1/0/2] qos trust dot1p [DeviceB-GigabitEthernet1/0/2] port link-type trunk [DeviceB-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30 [DeviceB-GigabitEthernet1/0/2] quit # Create RRPP domain 1. Configure VLAN 4092 as the primary control VLAN of RRPP domain 1, and configure the VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1. [DeviceB] rrpp domain 1 [DeviceB-rrpp-domain1] control-vlan 4092 [DeviceB-rrpp-domain1] protected-vlan reference-instance 1 # Configure Device B as the transit node of primary ring 1, with GigabitEthernet 1/0/1 as the primary port and GigabitEthernet 1/0/2 as the secondary port, and enable ring 1. [DeviceB-rrpp-domain1] ring 1 node-mode transit primary-port gigabitethernet 1/0/1 secondary-port gigabitethernet 1/0/2 level 0 [DeviceB-rrpp-domain1] ring 1 enable 64