HP 6125G HP 6125G & 6125G/XG Blade Switches High Availability Configur - Page 95
Con Device F as the master node of subring 3 in RRPP domain 1, with GigabitEthernet
View all HP 6125G manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 95 highlights
# Enable RRPP. [DeviceE] rrpp enable 6. Configure Device F: # Create VLAN 1, map VLAN 1 to MSTI 1, and activate MST region configuration. system-view [DeviceF] vlan 1 [DeviceF-vlan1] quit [DeviceF] stp region-configuration [DeviceF-mst-region] instance 1 vlan 1 [DeviceF-mst-region] active region-configuration [DeviceF-mst-region] quit # Cancel the physical state change suppression interval setting on GigabitEthernet 1/0/1 and GigabitEthernet 1/0/2, disable the spanning tree feature, and set the trusted packet priority type to 802.1p priority. Configure the two ports as trunk ports, and assign them to VLAN 1. [DeviceF] interface gigabitethernet 1/0/1 [DeviceF-GigabitEthernet1/0/1] undo link-delay [DeviceF-GigabitEthernet1/0/1] undo stp enable [DeviceF-GigabitEthernet1/0/1] qos trust dot1p [DeviceF-GigabitEthernet1/0/1] port link-type trunk [DeviceF-GigabitEthernet1/0/1] port trunk permit vlan 1 [DeviceF-GigabitEthernet1/0/1] quit [DeviceF] interface gigabitethernet 1/0/2 [DeviceF-GigabitEthernet1/0/2] undo link-delay [DeviceF-GigabitEthernet1/0/2] undo stp enable [DeviceF-GigabitEthernet1/0/2] qos trust dot1p [DeviceF-GigabitEthernet1/0/2] port link-type trunk [DeviceF-GigabitEthernet1/0/2] port trunk permit vlan 1 [DeviceF-GigabitEthernet1/0/2] quit # Create RRPP domain 1. Configure VLAN 100 as the primary control VLAN, and configure the VLAN mapped to MSTI 1 as the protected VLAN. [DeviceF] rrpp domain 1 [DeviceF-rrpp-domain1] control-vlan 100 [DeviceF-rrpp-domain1] protected-vlan reference-instance 1 # Configure Device F as the master node of subring 3 in RRPP domain 1, with GigabitEthernet 1/0/1 as the primary port and GigabitEthernet 1/0/2 as the secondary port, and enable subring 3. [DeviceF-rrpp-domain1] ring 3 node-mode master primary-port gigabitethernet 1/0/1 secondary-port gigabitethernet 1/0/2 level 1 [DeviceF-rrpp-domain1] ring 3 enable [DeviceF-rrpp-domain1] quit # Enable RRPP. [DeviceF] rrpp enable 7. RRPP ring group configurations on Device B and Device C after the configurations. # Create RRPP ring group 1 on Device B. Add subrings 2 and 3 to the RRPP ring group. [DeviceB] rrpp ring-group 1 [DeviceB-rrpp-ring-group1] domain 2 ring 2 [DeviceB-rrpp-ring-group1] domain 1 ring 3 88