HP 6125G HP 6125G & 6125G/XG Blade Switches High Availability Configur - Page 81
edge port, and enable subring 2
View all HP 6125G manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 81 highlights
[DeviceB-GigabitEthernet1/0/4] quit # Create RRPP domain 1. Configure VLAN 4092 as the primary control VLAN of RRPP domain 1, and configure the VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1. [DeviceB] rrpp domain 1 [DeviceB-rrpp-domain1] control-vlan 4092 [DeviceB-rrpp-domain1] protected-vlan reference-instance 1 # Configure Device B as the transit node of primary ring 1, with GigabitEthernet 1/0/1 as the primary port and GigabitEthernet 1/0/2 as the secondary port, and enable ring 1. [DeviceB-rrpp-domain1] ring 1 node-mode transit primary-port gigabitethernet 1/0/1 secondary-port gigabitethernet 1/0/2 level 0 [DeviceB-rrpp-domain1] ring 1 enable # Configure Device B as the assistant-edge node of subring 2, with GigabitEthernet 1/0/4 as the edge port, and enable subring 2. [DeviceB-rrpp-domain1] ring 2 node-mode assistant-edge edge-port gigabitethernet 1/0/4 [DeviceB-rrpp-domain1] ring 2 enable # Configure Device B as the assistant-edge node of subring 3, with GigabitEthernet 1/0/3 as the edge port, and enable subring 3. [DeviceB-rrpp-domain1] ring 3 node-mode assistant-edge edge-port gigabitethernet 1/0/3 [DeviceB-rrpp-domain1] ring 3 enable [DeviceB-rrpp-domain1] quit # Enable RRPP. [DeviceB] rrpp enable 3. Configure Device C: # Create VLANs 1 through 30, map these VLANs to MSTI 1, and activate the MST region configuration. system-view [DeviceC] vlan 1 to 30 [DeviceC] stp region-configuration [DeviceC-mst-region] instance 1 vlan 1 to 30 [DeviceC-mst-region] active region-configuration [DeviceC-mst-region] quit # Cancel the physical state change suppression interval setting on GigabitEthernet 1/0/1 through GigabitEthernet 1/0/4, disable the spanning tree feature, and set the trusted packet priority type to 802.1p priority. Configure the four ports as trunk ports, and assign them to VLANs 1 through 30. [DeviceC] interface gigabitethernet 1/0/1 [DeviceC-GigabitEthernet1/0/1] undo link-delay [DeviceC-GigabitEthernet1/0/1] undo stp enable [DeviceC-GigabitEthernet1/0/1] qos trust dot1p [DeviceC-GigabitEthernet1/0/1] port link-type trunk [DeviceC-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30 [DeviceC-GigabitEthernet1/0/1] quit [DeviceC] interface gigabitethernet 1/0/2 [DeviceC-GigabitEthernet1/0/2] undo link-delay [DeviceC-GigabitEthernet1/0/2] undo stp enable [DeviceC-GigabitEthernet1/0/2] qos trust dot1p 74