HP 6125G HP 6125G & 6125G/XG Blade Switches High Availability Configur - Page 94

Cancel the physical state change suppression interval setting on GigabitEthernet 1/0/1

Page 94 highlights

[DeviceD-rrpp-domain2] ring 1 node-mode transit primary-port gigabitethernet 1/0/1 secondary-port gigabitethernet 1/0/2 level 0 [DeviceD-rrpp-domain2] ring 1 enable [DeviceD-rrpp-domain2] quit # Enable RRPP. [DeviceD] rrpp enable 5. Configure Device E: # Create VLAN 2, map VLAN 2 to MSTI 2, and activate MST region configuration. system-view [DeviceE] vlan 2 [DeviceE-vlan2] quit [DeviceE] stp region-configuration [DeviceE-mst-region] instance 2 vlan 2 [DeviceE-mst-region] active region-configuration [DeviceE-mst-region] quit # Cancel the physical state change suppression interval setting on GigabitEthernet 1/0/1 and GigabitEthernet 1/0/2, disable the spanning tree feature, and set the trusted packet priority type to 802.1p priority. Configure the two ports as trunk ports, remove them from VLAN 1, assign them to VLAN 2, and configure VLAN 2 as their default VLAN. [DeviceE] interface gigabitethernet 1/0/1 [DeviceE-GigabitEthernet1/0/1] undo link-delay [DeviceE-GigabitEthernet1/0/1] undo stp enable [DeviceE-GigabitEthernet1/0/1] qos trust dot1p [DeviceE-GigabitEthernet1/0/1] port link-type trunk [DeviceE-GigabitEthernet1/0/1] undo port trunk permit vlan 1 [DeviceE-GigabitEthernet1/0/1] port trunk permit vlan 2 [DeviceE-GigabitEthernet1/0/1] port trunk pvid vlan 2 [DeviceE-GigabitEthernet1/0/1] quit [DeviceE] interface gigabitethernet 1/0/2 [DeviceE-GigabitEthernet1/0/2] undo link-delay [DeviceE-GigabitEthernet1/0/2] undo stp enable [DeviceE-GigabitEthernet1/0/2] qos trust dot1p [DeviceE-GigabitEthernet1/0/2] port link-type trunk [DeviceE-GigabitEthernet1/0/2] undo port trunk permit vlan 1 [DeviceE-GigabitEthernet1/0/2] port trunk permit vlan 2 [DeviceE-GigabitEthernet1/0/2] port trunk pvid vlan 2 [DeviceE-GigabitEthernet1/0/2] quit # Create RRPP domain 2. Configure VLAN 105 as the primary control VLAN, and configure the VLAN mapped to MSTI 2 as the protected VLAN. [DeviceE] rrpp domain 2 [DeviceE-rrpp-domain2] control-vlan 105 [DeviceE-rrpp-domain2] protected-vlan reference-instance 2 # Configure Device E as the master mode of subring 2 in RRPP domain 2, with GigabitEthernet 1/0/2 as the primary port and GigabitEthernet 1/0/1 as the secondary port, and enable ring 2. [DeviceE-rrpp-domain2] ring 2 node-mode master primary-port gigabitethernet 1/0/2 secondary-port gigabitethernet 1/0/1 level 1 [DeviceE-rrpp-domain2] ring 2 enable [DeviceE-rrpp-domain2] quit 87

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222

87
[DeviceD-rrpp-domain2] ring 1 node-mode transit primary-port gigabitethernet 1/0/1
secondary-port gigabitethernet 1/0/2 level 0
[DeviceD-rrpp-domain2] ring 1 enable
[DeviceD-rrpp-domain2] quit
# Enable RRPP.
[DeviceD] rrpp enable
5.
Configure Device E:
# Create VLAN 2, map VLAN 2 to MSTI 2, and activate MST region configuration.
<DeviceE> system-view
[DeviceE] vlan 2
[DeviceE-vlan2] quit
[DeviceE] stp region-configuration
[DeviceE-mst-region] instance 2 vlan 2
[DeviceE-mst-region] active region-configuration
[DeviceE-mst-region] quit
# Cancel the physical state change suppression interval setting on GigabitEthernet 1/0/1 and
GigabitEthernet 1/0/2, disable the spanning tree feature, and set the trusted packet priority type
to 802.1p priority. Configure the two ports as trunk ports, remove them from VLAN 1, assign them
to VLAN 2, and configure VLAN 2 as their default VLAN.
[DeviceE] interface gigabitethernet 1/0/1
[DeviceE-GigabitEthernet1/0/1] undo link-delay
[DeviceE-GigabitEthernet1/0/1] undo stp enable
[DeviceE-GigabitEthernet1/0/1] qos trust dot1p
[DeviceE-GigabitEthernet1/0/1] port link-type trunk
[DeviceE-GigabitEthernet1/0/1] undo port trunk permit vlan 1
[DeviceE-GigabitEthernet1/0/1] port trunk permit vlan 2
[DeviceE-GigabitEthernet1/0/1] port trunk pvid vlan 2
[DeviceE-GigabitEthernet1/0/1] quit
[DeviceE] interface gigabitethernet 1/0/2
[DeviceE-GigabitEthernet1/0/2] undo link-delay
[DeviceE-GigabitEthernet1/0/2] undo stp enable
[DeviceE-GigabitEthernet1/0/2] qos trust dot1p
[DeviceE-GigabitEthernet1/0/2] port link-type trunk
[DeviceE-GigabitEthernet1/0/2] undo port trunk permit vlan 1
[DeviceE-GigabitEthernet1/0/2] port trunk permit vlan 2
[DeviceE-GigabitEthernet1/0/2] port trunk pvid vlan 2
[DeviceE-GigabitEthernet1/0/2] quit
# Create RRPP domain 2. Configure VLAN 105 as the primary control VLAN, and configure the
VLAN mapped to MSTI 2 as the protected VLAN.
[DeviceE] rrpp domain 2
[DeviceE-rrpp-domain2] control-vlan 105
[DeviceE-rrpp-domain2] protected-vlan reference-instance 2
# Configure Device E as the master mode of subring 2 in RRPP domain 2, with GigabitEthernet
1/0/2 as the primary port and GigabitEthernet 1/0/1 as the secondary port, and enable ring 2.
[DeviceE-rrpp-domain2] ring 2 node-mode master primary-port gigabitethernet 1/0/2
secondary-port gigabitethernet 1/0/1 level 1
[DeviceE-rrpp-domain2] ring 2 enable
[DeviceE-rrpp-domain2] quit