HP 6125G HP 6125G & 6125G/XG Blade Switches High Availability Configur - Page 93

Create RRPP domain 1. Con VLAN 100 as the primary control VLAN of RRPP domain 1

Get HP 6125G PDF manuals and user guides View all HP 6125G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 93 highlights

[DeviceC] rrpp enable 4. Configure Device D: # Create VLANs 1 and 2, map VLAN 1 to MSTI 1 and VLAN 2 to MSTI 2, and activate MST region configuration. system-view [DeviceD] vlan 1 to 2 [DeviceD] stp region-configuration [DeviceD-mst-region] instance 1 vlan 1 [DeviceD-mst-region] instance 2 vlan 2 [DeviceD-mst-region] active region-configuration [DeviceD-mst-region] quit # Cancel the physical state change suppression interval setting on GigabitEthernet 1/0/1 and GigabitEthernet 1/0/2, disable the spanning tree feature, and set the trusted packet priority type to 802.1p priority. Configure the two ports as trunk ports, and assign them to VLAN 1 and VLAN 2. [DeviceD] interface gigabitethernet 1/0/1 [DeviceD-GigabitEthernet1/0/1] undo link-delay [DeviceD-GigabitEthernet1/0/1] undo stp enable [DeviceD-GigabitEthernet1/0/1] qos trust dot1p [DeviceD-GigabitEthernet1/0/1] port link-type trunk [DeviceD-GigabitEthernet1/0/1] port trunk permit vlan 1 2 [DeviceD-GigabitEthernet1/0/1] quit [DeviceD] interface gigabitethernet 1/0/2 [DeviceD-GigabitEthernet1/0/2] undo link-delay [DeviceD-GigabitEthernet1/0/2] undo stp enable [DeviceD-GigabitEthernet1/0/2] qos trust dot1p [DeviceD-GigabitEthernet1/0/2] port link-type trunk [DeviceD-GigabitEthernet1/0/2] port trunk permit vlan 1 2 [DeviceD-GigabitEthernet1/0/2] quit # Create RRPP domain 1. Configure VLAN 100 as the primary control VLAN of RRPP domain 1, and configure the VLAN mapped to MSTI 1 as the protected VLAN of RRPP domain 1. [DeviceD] rrpp domain 1 [DeviceD-rrpp-domain1] control-vlan 100 [DeviceD-rrpp-domain1] protected-vlan reference-instance 1 # Configure Device D as the transit node of primary ring 1 in RRPP domain 1, with GigabitEthernet 1/0/1 as the primary port and GigabitEthernet 1/0/2 as the secondary port, and enable ring 1. [DeviceD-rrpp-domain1] ring 1 node-mode transit primary-port gigabitethernet 1/0/1 secondary-port gigabitethernet 1/0/2 level 0 [DeviceD-rrpp-domain1] ring 1 enable [DeviceD-rrpp-domain1] quit # Create RRPP domain 2. Configure VLAN 105 as the primary control VLAN of RRPP domain 2, and configure the VLAN mapped to MSTI 2 as the protected VLAN of RRPP domain 2. [DeviceD] rrpp domain 2 [DeviceD-rrpp-domain2] control-vlan 105 [DeviceD-rrpp-domain2] protected-vlan reference-instance 2 # Configure Device D as the transit node of primary ring 1 in RRPP domain 2, with GigabitEthernet 1/0/1 as the primary port and GigabitEthernet 1/0/2 as the secondary port, and enable ring 1. 86

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
86
[DeviceC] rrpp enable
4.
Configure Device D:
# Create VLANs 1 and 2, map VLAN 1 to MSTI 1 and VLAN 2 to MSTI 2, and activate MST region
configuration.
<DeviceD> system-view
[DeviceD] vlan 1 to 2
[DeviceD] stp region-configuration
[DeviceD-mst-region] instance 1 vlan 1
[DeviceD-mst-region] instance 2 vlan 2
[DeviceD-mst-region] active region-configuration
[DeviceD-mst-region] quit
# Cancel the physical state change suppression interval setting on GigabitEthernet 1/0/1 and
GigabitEthernet 1/0/2, disable the spanning tree feature, and set the trusted packet priority type
to 802.1p priority. Configure the two ports as trunk ports, and assign them to VLAN 1 and VLAN
2.
[DeviceD] interface gigabitethernet 1/0/1
[DeviceD-GigabitEthernet1/0/1] undo link-delay
[DeviceD-GigabitEthernet1/0/1] undo stp enable
[DeviceD-GigabitEthernet1/0/1] qos trust dot1p
[DeviceD-GigabitEthernet1/0/1] port link-type trunk
[DeviceD-GigabitEthernet1/0/1] port trunk permit vlan 1 2
[DeviceD-GigabitEthernet1/0/1] quit
[DeviceD] interface gigabitethernet 1/0/2
[DeviceD-GigabitEthernet1/0/2] undo link-delay
[DeviceD-GigabitEthernet1/0/2] undo stp enable
[DeviceD-GigabitEthernet1/0/2] qos trust dot1p
[DeviceD-GigabitEthernet1/0/2] port link-type trunk
[DeviceD-GigabitEthernet1/0/2] port trunk permit vlan 1 2
[DeviceD-GigabitEthernet1/0/2] quit
# Create RRPP domain 1. Configure VLAN 100 as the primary control VLAN of RRPP domain 1,
and configure the VLAN mapped to MSTI 1 as the protected VLAN of RRPP domain 1.
[DeviceD] rrpp domain 1
[DeviceD-rrpp-domain1] control-vlan 100
[DeviceD-rrpp-domain1] protected-vlan reference-instance 1
# Configure Device D as the transit node of primary ring 1 in RRPP domain 1, with GigabitEthernet
1/0/1 as the primary port and GigabitEthernet 1/0/2 as the secondary port, and enable ring 1.
[DeviceD-rrpp-domain1] ring 1 node-mode transit primary-port gigabitethernet 1/0/1
secondary-port gigabitethernet 1/0/2 level 0
[DeviceD-rrpp-domain1] ring 1 enable
[DeviceD-rrpp-domain1] quit
# Create RRPP domain 2. Configure VLAN 105 as the primary control VLAN of RRPP domain 2,
and configure the VLAN mapped to MSTI 2 as the protected VLAN of RRPP domain 2.
[DeviceD] rrpp domain 2
[DeviceD-rrpp-domain2] control-vlan 105
[DeviceD-rrpp-domain2] protected-vlan reference-instance 2
# Configure Device D as the transit node of primary ring 1 in RRPP domain 2, with GigabitEthernet
1/0/1 as the primary port and GigabitEthernet 1/0/2 as the secondary port, and enable ring 1.