HP 6125G HP 6125G & 6125G/XG Blade Switches High Availability Configur - Page 89
and con the VLAN mapped to MSTI 2 as the protected VLAN of RRPP domain 2
View all HP 6125G manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 89 highlights
[DeviceA-GigabitEthernet1/0/2] quit # Create RRPP domain 1. Configure VLAN 100 as the primary control VLAN of RRPP domain 1, and configure the VLAN mapped to MSTI 1 as the protected VLAN of RRPP domain 1. [DeviceA] rrpp domain 1 [DeviceA-rrpp-domain1] control-vlan 100 [DeviceA-rrpp-domain1] protected-vlan reference-instance 1 # Configure Device A as the master node of primary ring 1, with GigabitEthernet 1/0/1 as the primary port and GigabitEthernet 1/0/2 as the secondary port, and enable ring 1. [DeviceA-rrpp-domain1] ring 1 node-mode master primary-port gigabitethernet 1/0/1 secondary-port gigabitethernet 1/0/2 level 0 [DeviceA-rrpp-domain1] ring 1 enable [DeviceA-rrpp-domain1] quit # Create RRPP domain 2, configure VLAN 105 as the primary control VLAN of RRPP domain 2, and configure the VLAN mapped to MSTI 2 as the protected VLAN of RRPP domain 2. [DeviceA] rrpp domain 2 [DeviceA-rrpp-domain2] control-vlan 105 [DeviceA-rrpp-domain2] protected-vlan reference-instance 2 # Configure Device A as the master node of primary ring 1, with GigabitEthernet 1/0/2 as the master port and GigabitEthernet 1/0/1 as the secondary port, and enable ring 1. [DeviceA-rrpp-domain2] ring 1 node-mode master primary-port gigabitethernet 1/0/2 secondary-port gigabitethernet 1/0/1 level 0 [DeviceA-rrpp-domain2] ring 1 enable [DeviceA-rrpp-domain2] quit # Enable RRPP. [DeviceA] rrpp enable 2. Configure Device B: # Create VLANs 1 and 2, map VLAN 1 to MSTI 1 and VLAN 2 to MSTI 2, and activate MST region configuration. system-view [DeviceB] vlan 1 to 2 [DeviceB] stp region-configuration [DeviceB-mst-region] instance 1 vlan 1 [DeviceB-mst-region] instance 2 vlan 2 [DeviceB-mst-region] active region-configuration [DeviceB-mst-region] quit # Cancel the physical state change suppression interval setting on GigabitEthernet 1/0/1 and GigabitEthernet 1/0/2, disable the spanning tree feature, and set the trusted packet priority type to 802.1p priority. Configure the two ports as trunk ports, and assign them to VLAN 1 and VLAN 2. [DeviceB] interface gigabitethernet 1/0/1 [DeviceB-GigabitEthernet1/0/1] undo link-delay [DeviceB-GigabitEthernet1/0/1] undo stp enable [DeviceB-GigabitEthernet1/0/1] qos trust dot1p [DeviceB-GigabitEthernet1/0/1] port link-type trunk [DeviceB-GigabitEthernet1/0/1] port trunk permit vlan 1 2 [DeviceB-GigabitEthernet1/0/1] quit [DeviceB] interface gigabitethernet 1/0/2 82