D-Link 3312SR Reference Manual - Page 112

DGS-3312SR Layer 3 Gigabit Switch

106

config vlan

forbidden

−

Specifies the ports as forbidden ports.

delete

−

Used to delete ports from the specified VLAN, in

conjunction with the

portlist

parameter.

<portlist>

−

A range of ports to add to the VLAN. The port list is

specified by listing the lowest switch number and the beginning

port number on that switch, separated by a colon. Then the

highest switch number, and the highest port number of the range

(also separated by a colon) are specified. The beginning and end

of the port list range are separated by a dash. For example, 1:3

specifies switch number 1, port 3. 2:4 specifies switch number 2,

port 4. 1:3-2:4 specifies all of the ports between switch 1, port 3

and switch 2, port 4

−

in numerical order.

advertisement [enable | disable ]

−

Enables or disables GVRP on

the specified VLAN.

Restrictions

Only administrator-level users can issue this command.

Example usage:

To add 4 through 8 of module 2 as tagged ports to the VLAN v1:

DGS-3312SR:4#config vlan v1 add tagged 2:4-2:8

Command: config vlan v1 add tagged 2:4-2:8

Success.

DGS-3312SR:4#

config gvrp

Purpose

Used to configure GVRP on the switch.

Syntax

config gvrp [<portlist> | all] {state [enable | disable] |

ingress_checking [enable | disable] | acceptable_frame

[tagged_only | admit_all] | pvid <vlanid 1-4094>}

Description

This command is used to configure the Group VLAN Registration

Protocol on the switch. You can configure ingress checking, the

sending and receiving of GVRP information, and the Port VLAN ID

(PVID).

Parameters

<portlist>

−

A range of ports for which you want ingress checking.

The port list is specified by listing the lowest switch number and

the beginning port number on that switch, separated by a colon.

Then the highest switch number, and the highest port number of

the range (also separated by a colon) are specified. The beginning

and end of the port list range are separated by a dash. For

example, 1:3 specifies switch number 1, port 3. 2:4 specifies

switch number 2, port 4. 1:3-2:4 specifies all of the ports between

switch 1, port 3 and switch 2, port 4

−

in numerical order.

all

−

Specifies all of the ports on the switch.

Section	Page
Introduction	7
	7
	7
Accessing the Switch via the Serial Port	7
Setting the Switch’s IP Address	8
Using the Console CLI	10
	10
	10
Connecting to the Switch	10
Command Syntax	16
Basic Switch Commands	18
Switch Port Commands	30
Port Security Commands	33
Network Management (SNMP) Commands	37
Switch Utility Commands	58
Network Monitoring Commands	62
Multiple Spanning Tree Protocol (MSTP) Commands	75
Forwarding Database Commands	88
Broadcast Storm Control Commands	95
QoS Commands	97
Port Mirroring Commands	105
VLAN Commands	110
Link Aggregation Commands	117
IP Commands (Including IP Multinetting)	123
IGMP Commands	128
IGMP Snooping Commands	131
MAC Notification Commands	139
Access Authentication Control Commands	143
SSH Commands	167
SSL Commands	175
802.1X Commands	180
Access Control List (ACL) Commands	192
Traffic Segmentation Commands	201
Stacking Commands	203
D-Link Single IP Management Commands	206
Time and SNTP Commands	216
ARP Commands	222
VRRP Commands	226
Routing Table Commands	233
Route Redistribution Commands	237
BOOTP Relay Commands	243
DNS Relay Commands	247
RIP Commands	251
DVMRP Commands	254
PIM Commands	259
IP Multicasting Commands	263
MD5 Configuration Commands	265
OSPF Configuration Commands	268
Command History List	288
Technical Specifications	290
	296
	296
	296
	296
	296
	296
	296
Copyright Statement: No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Co	296

D-Link 3312SR Reference Manual - Page 112

config vlan, config gvrp, Command: config vlan v1 add tagged 2:4-2:8

Page 112 highlights