D-Link 3312SR Reference Manual - Page 155

DGS-3312SR Layer 3 Gigabit Switch

149

To display all method lists for promoting user level privileges to administrator level privileges.

DGS-3312SR:4#show authen_enable all

Command: show authen_enable all

Method List Name

Priority

Method Name

Comment

----------------

--------

---------------

------------------

Permit

1

tacacs+

Built-in Group

2

tacacs

Built-in Group

3

Darren

User-defined Group

4

local

Keyword

default

1

tacacs+

Built-in Group

2

local

Keyword

Total Entries : 2

DGS-3312SR:4#

config authen application

Purpose

Used to configure various applications on the switch for

authentication using a previously configured method list.

Syntax

config authen application [console | telnet | ssh | http | all]

[login | enable] [default | method_list_name <string 15>]

Description

This command is used to configure switch configuration applications

(console, telnet, ssh, web) for login at the user level and at the

administration level (

authen_enable

) utilizing a previously configured

method list.

Parameters

application

– Choose the application to configure. The user may

choose one of the following four applications to configure.

±

console

– Choose this parameter to configure the

command line interface login method.

±

telnet

– Choose this parameter to configure the telnet login

method.

±

ssh

– Choose this parameter to configure the ssh login

method.

±

http

– Choose this parameter to configure the web interface

login method.

±

all

– Choose this parameter to configure all applications

(console, telnet, web) login method.

login

– Use this parameter to configure an application for normal

login on the user level, using a previously configured method list.

enable

- Use this parameter to configure an application for

upgrading a normal user level to administrator privileges, using a

previously configured method list.

default

– Use this parameter to configure an application for user

authentication using the default method list.

method_list_name <string 15>

- Use this parameter to configure an

application for user authentication using a previously configured

method list. Enter a alphanumeric string of up to 15 characters to

define a previously configured method list.

Section	Page
Introduction	7
	7
	7
Accessing the Switch via the Serial Port	7
Setting the Switch’s IP Address	8
Using the Console CLI	10
	10
	10
Connecting to the Switch	10
Command Syntax	16
Basic Switch Commands	18
Switch Port Commands	30
Port Security Commands	33
Network Management (SNMP) Commands	37
Switch Utility Commands	58
Network Monitoring Commands	62
Multiple Spanning Tree Protocol (MSTP) Commands	75
Forwarding Database Commands	88
Broadcast Storm Control Commands	95
QoS Commands	97
Port Mirroring Commands	105
VLAN Commands	110
Link Aggregation Commands	117
IP Commands (Including IP Multinetting)	123
IGMP Commands	128
IGMP Snooping Commands	131
MAC Notification Commands	139
Access Authentication Control Commands	143
SSH Commands	167
SSL Commands	175
802.1X Commands	180
Access Control List (ACL) Commands	192
Traffic Segmentation Commands	201
Stacking Commands	203
D-Link Single IP Management Commands	206
Time and SNTP Commands	216
ARP Commands	222
VRRP Commands	226
Routing Table Commands	233
Route Redistribution Commands	237
BOOTP Relay Commands	243
DNS Relay Commands	247
RIP Commands	251
DVMRP Commands	254
PIM Commands	259
IP Multicasting Commands	263
MD5 Configuration Commands	265
OSPF Configuration Commands	268
Command History List	288
Technical Specifications	290
	296
	296
	296
	296
	296
	296
	296
Copyright Statement: No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Co	296

D-Link 3312SR Reference Manual - Page 155

config authen application

Page 155 highlights