D-Link 3312SR Reference Manual - Page 83

DGS-3312SR Layer 3 Gigabit Switch

77

config stp mst_config_id

Purpose

Used to update the MSTP configuration identification.

Syntax

config stp mst_config_id {revision_level <int 0-65535> | name

<string>

Description

This command will uniquely identify the MSTP configuration

currently configured on the Switch. Information entered here will

be attached to BDPU packets as an identifier for the MSTP region

to which it belongs. Switches having the same

revision_level

and

name

will be considered as part of the same MSTP region.

Parameters

revision_level <int 0-65535>

– Enter a number between 0 and

65535 to identify the MSTP region. This value, along with the

name will identify the MSTP region configured on the Switch. The

default setting is

0

.

name <string>

- Enter an alphanumeric string of up to 32

characters to uniquely identify the MSTP region on the Switch.

This

name

, along with the

revision_level

value will identify the

MSTP region configured on the Switch. If no

name

is entered, the

default name will be the MAC address of the device.

Restrictions

Only administrator-level users can issue this command.

Example usage:

To configure the MSTP region of the Switch with

revision_level

10 and the

name

“Trinity”:

DGS-3312SR:4#config stp mst_config_id revision_level 10 name Trinity

Command : config stp mst_config_id revision_level 10 name Trinity

Success.

DGS-3312SR:4#

config stp mst_ports

Purpose

Used to update the port configuration for a MSTP instance.

Syntax

config stp mst_ports <portlist> instance_id <value 0-15>

{internalCost [auto | <value 1-20000000>] `priority <value 0-

240>}

Description

This command will update the port configuration for a STP

instance_id

. If a loop occurs, the MSTP function will use the port

priority to select an interface to put into the forwarding state. Set a

higher priority value for interfaces to be selected for forwarding

first. In instances where the priority value is identical, the MSTP

function will implement the lowest port number into the forwarding

state and other interfaces will be blocked. Remember that lower

priority values mean higher priorities for forwarding packets.

Parameters

<portlist>

- Specifies a port or range of ports to be configured. The

port list is specified by listing the lowest switch number and the

beginning port number on that switch, separated by a colon. Then

the highest switch number, and the highest port number of the

range (also separated by a colon) are specified. The beginning

and end of the port list range are separated by a dash. For

Section	Page
Introduction	7
	7
	7
Accessing the Switch via the Serial Port	7
Setting the Switch’s IP Address	8
Using the Console CLI	10
	10
	10
Connecting to the Switch	10
Command Syntax	16
Basic Switch Commands	18
Switch Port Commands	30
Port Security Commands	33
Network Management (SNMP) Commands	37
Switch Utility Commands	58
Network Monitoring Commands	62
Multiple Spanning Tree Protocol (MSTP) Commands	75
Forwarding Database Commands	88
Broadcast Storm Control Commands	95
QoS Commands	97
Port Mirroring Commands	105
VLAN Commands	110
Link Aggregation Commands	117
IP Commands (Including IP Multinetting)	123
IGMP Commands	128
IGMP Snooping Commands	131
MAC Notification Commands	139
Access Authentication Control Commands	143
SSH Commands	167
SSL Commands	175
802.1X Commands	180
Access Control List (ACL) Commands	192
Traffic Segmentation Commands	201
Stacking Commands	203
D-Link Single IP Management Commands	206
Time and SNTP Commands	216
ARP Commands	222
VRRP Commands	226
Routing Table Commands	233
Route Redistribution Commands	237
BOOTP Relay Commands	243
DNS Relay Commands	247
RIP Commands	251
DVMRP Commands	254
PIM Commands	259
IP Multicasting Commands	263
MD5 Configuration Commands	265
OSPF Configuration Commands	268
Command History List	288
Technical Specifications	290
	296
	296
	296
	296
	296
	296
	296
Copyright Statement: No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Co	296

D-Link 3312SR Reference Manual - Page 83

config stp mst_config_id, config stp mst_ports

Page 83 highlights