D-Link 3312SR Reference Manual - Page 132

DGS-3312SR Layer 3 Gigabit Switch

126

config igmp_snooping

without the switch receiving a host membership report. The

default is 260 seconds.

router_timeout <sec 1-16711450>

−

Specifies the maximum

amount of time a route can be a member of a multicast group

without the switch receiving a host membership report. The

default is 260 seconds.

leave_timer <sec 0-16711450>

−

Leave timer. The default is 2

seconds.

state [enable | disable]

−

Allows you to enable or disable IGMP

snooping for the specified VLAN.

Restrictions

Only administrator-level users can issue this command.

Example usage:

To configure the igmp snooping:

DGS-3312SR:4#config igmp_snooping default host_timeout 250 state enable

Command: config igmp_snooping default host_timeout 250 state enable

Success.

DGS-3312SR:4#

config igmp_snooping querier

Purpose

This command configures IGMP snooping querier.

Syntax

config igmp_snooping querier [<vlan_name 32> | all]

{query_interval <sec 1-65535> | max_response_time <sec 1-

25> | robustness_variable <value 1-255> |

last_member_query_interval <sec 1-25> | state [enable |

disable]

Description

Used to configure the time in seconds between general query

transmissions, the maximum time in seconds to wait for reports

from members and the permitted packet loss that guarantees

IGMP snooping.

Parameters

<vlan_name 32>

−

The name of the VLAN for which IGMP

snooping querier is to be configured.

all

– Selecting this parameter will configure the IGMP snooping

querier for all VLANs on the switch.

query_interval <sec 1-65535>

−

Specifies the amount of time in

seconds between general query transmissions. The default

setting is 125 seconds.

max_response_time <sec 1-25>

−

Specifies the maximum time in

seconds to wait for reports from members. The default setting is

10 seconds.

Section	Page
Introduction	7
	7
	7
Accessing the Switch via the Serial Port	7
Setting the Switch’s IP Address	8
Using the Console CLI	10
	10
	10
Connecting to the Switch	10
Command Syntax	16
Basic Switch Commands	18
Switch Port Commands	30
Port Security Commands	33
Network Management (SNMP) Commands	37
Switch Utility Commands	58
Network Monitoring Commands	62
Multiple Spanning Tree Protocol (MSTP) Commands	75
Forwarding Database Commands	88
Broadcast Storm Control Commands	95
QoS Commands	97
Port Mirroring Commands	105
VLAN Commands	110
Link Aggregation Commands	117
IP Commands (Including IP Multinetting)	123
IGMP Commands	128
IGMP Snooping Commands	131
MAC Notification Commands	139
Access Authentication Control Commands	143
SSH Commands	167
SSL Commands	175
802.1X Commands	180
Access Control List (ACL) Commands	192
Traffic Segmentation Commands	201
Stacking Commands	203
D-Link Single IP Management Commands	206
Time and SNTP Commands	216
ARP Commands	222
VRRP Commands	226
Routing Table Commands	233
Route Redistribution Commands	237
BOOTP Relay Commands	243
DNS Relay Commands	247
RIP Commands	251
DVMRP Commands	254
PIM Commands	259
IP Multicasting Commands	263
MD5 Configuration Commands	265
OSPF Configuration Commands	268
Command History List	288
Technical Specifications	290
	296
	296
	296
	296
	296
	296
	296
Copyright Statement: No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Co	296

D-Link 3312SR Reference Manual - Page 132

config igmp_snooping, DGS-3312SR:4#config igmp_snooping default host_timeout 250 state enable

Page 132 highlights