D-Link 3312SR Reference Manual - Page 95

DGS-3312SR Layer 3 Gigabit Switch

89

12

B

ROADCAST

S

TORM

C

ONTROL

C

OMMANDS

The broadcast storm control commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters)

in the following table.

Command

Parameters

config traffic control

[<storm_grouplist> | all ] {broadcast [enable | disable] | multicast

[enable | disable] | dlf [enable | disable] | threshold <value 0-

255> }

show traffic control

{group_list <storm_grouplist>}

Each command is listed, in detail, in the following sections.

NOTE:

As a stand-alone switch or as a master switch in a switch stack,

the switch number will be referred to as 15 for all configurations, graphs

and tables.

config traffic control

Purpose

Used to configure broadcast/multicast traffic control.

Syntax

config traffic control [<storm_grouplist> | all] {broadcast

[enable | disable] | multicast [enable | disable] | dlf [enable |

disable] | threshold <value 0-255>}

Description

This command is used to configure broadcast storm control.

Parameters

<storm_grouplist>

−

Used to specify a broadcast storm control

group. This is specified by listing the lowest switch number and

the beginning port number on that switch, separated by a colon.

Then the highest switch number, and the highest port number of

the range (also separated by a colon) are specified. The beginning

and end of the port list range are separated by a dash. For

example, 1:3 specifies switch number 1, port 3. 2:4 specifies

switch number 2, port 4. 1:3-2:4 specifies all of the ports between

switch 1, port 3 and switch 2, port 4

−

in numerical order.

all

−

Specifies all storm control groups on the switch.

broadcast [enable | disable]

−

Enables or disables broadcast

storm control.

multicast [enable | disable]

−

Enables or disables multicast storm

control.

dlf [enable | disable]

−

Enables or disables dlf traffic control.

threshold <value 0-255>

−

The upper threshold at which the

specified traffic control is switched on. The

<value>

is the number

of broadcast / multicast / dlf packets, in Kbps, received by the

switch that will trigger the storm traffic control measures.

Restrictions

Only administrator-level users can issue this command.

Example usage:

Section	Page
Introduction	7
	7
	7
Accessing the Switch via the Serial Port	7
Setting the Switch’s IP Address	8
Using the Console CLI	10
	10
	10
Connecting to the Switch	10
Command Syntax	16
Basic Switch Commands	18
Switch Port Commands	30
Port Security Commands	33
Network Management (SNMP) Commands	37
Switch Utility Commands	58
Network Monitoring Commands	62
Multiple Spanning Tree Protocol (MSTP) Commands	75
Forwarding Database Commands	88
Broadcast Storm Control Commands	95
QoS Commands	97
Port Mirroring Commands	105
VLAN Commands	110
Link Aggregation Commands	117
IP Commands (Including IP Multinetting)	123
IGMP Commands	128
IGMP Snooping Commands	131
MAC Notification Commands	139
Access Authentication Control Commands	143
SSH Commands	167
SSL Commands	175
802.1X Commands	180
Access Control List (ACL) Commands	192
Traffic Segmentation Commands	201
Stacking Commands	203
D-Link Single IP Management Commands	206
Time and SNTP Commands	216
ARP Commands	222
VRRP Commands	226
Routing Table Commands	233
Route Redistribution Commands	237
BOOTP Relay Commands	243
DNS Relay Commands	247
RIP Commands	251
DVMRP Commands	254
PIM Commands	259
IP Multicasting Commands	263
MD5 Configuration Commands	265
OSPF Configuration Commands	268
Command History List	288
Technical Specifications	290
	296
	296
	296
	296
	296
	296
	296
Copyright Statement: No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Co	296

D-Link 3312SR Reference Manual - Page 95

Broadcast Storm Control Commands, config traffic control

Page 95 highlights