D-Link 3312SR Reference Manual - Page 254

DGS-3312SR Layer 3 Gigabit Switch

248

37

DVMRP C

OMMANDS

The DVMRP commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the

following table.

Command

Parameters

config dvmrp

[ipif <ipif_name 12> | all] {metric <value 1-31> | probe <sec 1-

65535> | neighbor_timeout <sec 1-65535> | state [enable |

disable]}

enable dvmrp

disable dvmrp

show dvmrp neighbor

{ipif <ipif_name 12> | ipaddress <network_address>}

show dvmrp nexthop

{ipaddress <network_address> | ipif <ipif_name 12>}

show dvmrp

routing_table

{ipaddress <network_address>}

show dvmrp

{ipif <ipif_name 12>}

Each command is listed, in detail, in the following sections.

NOTE:

Due to a switch limitation, DVMRP cannot function for

Secondary IP interfaces, although the DVMRP settings for the

Secondary IP Interface will be displayed. For more information

regarding configuring Primary and Secondary IP Interfaces, see the

IP Interface Settings and IP Multinetting

section of the DGS-

3312SR Manual.

config dvmrp

Purpose

Used to configure DVMRP on the switch.

Syntax

config dvmrp [ipif <ipif_name 12> | all] {metric <value 1-31> | probe

<sec 1-65535> | neighbor_timeout <sec 1-65535> | state [enable |

disable]}

Description

This command is used to configure DVMRP on the switch.

Parameters

<ipif_name 12>

−

The name of the IP interface for which DVMRP is to

be configured.

all

−

Specifies that DVMRP is to be configured for all IP interfaces on

the switch.

metric <value 1-31>

−

Allows the assignment of a DVMRP route cost to

the above IP interface. A DVMRP route cost is a relative number that

represents the real cost of using this route in the construction of a

multicast delivery tree.

It is similar to, but not defined as, the hop count

in RIP. The default is 1.

probe <second 1-65535>

−

DVMRP defined an extension to IGMP that

allows routers to query other routers to determine if a DVMRP neighbor

is present on a given subnetwork or not. This is referred to as a ‘probe’.

This entry will set an intermittent probe (in seconds) on the device that

will transmit dvmrp messages, depending on the time specified. This

Section	Page
Introduction	7
	7
	7
Accessing the Switch via the Serial Port	7
Setting the Switch’s IP Address	8
Using the Console CLI	10
	10
	10
Connecting to the Switch	10
Command Syntax	16
Basic Switch Commands	18
Switch Port Commands	30
Port Security Commands	33
Network Management (SNMP) Commands	37
Switch Utility Commands	58
Network Monitoring Commands	62
Multiple Spanning Tree Protocol (MSTP) Commands	75
Forwarding Database Commands	88
Broadcast Storm Control Commands	95
QoS Commands	97
Port Mirroring Commands	105
VLAN Commands	110
Link Aggregation Commands	117
IP Commands (Including IP Multinetting)	123
IGMP Commands	128
IGMP Snooping Commands	131
MAC Notification Commands	139
Access Authentication Control Commands	143
SSH Commands	167
SSL Commands	175
802.1X Commands	180
Access Control List (ACL) Commands	192
Traffic Segmentation Commands	201
Stacking Commands	203
D-Link Single IP Management Commands	206
Time and SNTP Commands	216
ARP Commands	222
VRRP Commands	226
Routing Table Commands	233
Route Redistribution Commands	237
BOOTP Relay Commands	243
DNS Relay Commands	247
RIP Commands	251
DVMRP Commands	254
PIM Commands	259
IP Multicasting Commands	263
MD5 Configuration Commands	265
OSPF Configuration Commands	268
Command History List	288
Technical Specifications	290
	296
	296
	296
	296
	296
	296
	296
Copyright Statement: No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Co	296

D-Link 3312SR Reference Manual - Page 254

DVMRP Commands, config dvmrp

Page 254 highlights