D-Link 3312SR Reference Manual - Page 240

DGS-3312SR Layer 3 Gigabit Switch

234

Allowed Metric Type combinations are

mettype 1

or

mettype 2

.

The metric value

0

above will be redistributed in OSPF as the

metric

20

.

Example Usage:

To configure route redistributions:

DGS-3312SR:4#config route redistribute dst ospf src all metric 2

Command: config route redistribute dst ospf src all metric 2

Success.

DGS-3312SR:4#

config route redistribute dst rip src

Purpose

Used configure route redistribution settings for the exchange of

RIP routes to OSPF routes on the switch.

Syntax

config route redistribute dst rip src [local | static | ospf | [all |

internal | external | type_1 | type_2 | inter+e1 | inter+e2]]

{metric <value>}

Description

Route redistribution allows routers on the network that are running

different routing protocols to exchange routing information. This is

accomplished by comparing the routes stored in the various

router’s routing tables and assigning appropriate metrics. This

information is then exchanged among the various routers

according to the individual routers current routing protocol. The

switch can redistribute routing information between the OSPF and

RIP routing protocols to all routers on the network that are running

OSPF or RIP. Routing information entered into the Static Routing

Table on the local switch is also redistributed.

Parameters

src {all | internal | external | type_1 | type_2 | inter+e1 | inter+e2}

−

Allows the selection of the protocol of the source device.

metric <value>

−

Allows the entry of an OSPF interface cost. This

is analogous to a Hop Count in the RIP routing protocol.

Restrictions

Only administrator-level users can issue this command.

Example Usage:

To configure route redistributions:

DGS-3312SR:4#config route redistribute dst ospf src rip mettype

type_1 metric 2

Command: config route redistribute dst ospf src rip mettype

type_1 metric 2

Success.

DGS-3312SR:4#

Section	Page
Introduction	7
	7
	7
Accessing the Switch via the Serial Port	7
Setting the Switch’s IP Address	8
Using the Console CLI	10
	10
	10
Connecting to the Switch	10
Command Syntax	16
Basic Switch Commands	18
Switch Port Commands	30
Port Security Commands	33
Network Management (SNMP) Commands	37
Switch Utility Commands	58
Network Monitoring Commands	62
Multiple Spanning Tree Protocol (MSTP) Commands	75
Forwarding Database Commands	88
Broadcast Storm Control Commands	95
QoS Commands	97
Port Mirroring Commands	105
VLAN Commands	110
Link Aggregation Commands	117
IP Commands (Including IP Multinetting)	123
IGMP Commands	128
IGMP Snooping Commands	131
MAC Notification Commands	139
Access Authentication Control Commands	143
SSH Commands	167
SSL Commands	175
802.1X Commands	180
Access Control List (ACL) Commands	192
Traffic Segmentation Commands	201
Stacking Commands	203
D-Link Single IP Management Commands	206
Time and SNTP Commands	216
ARP Commands	222
VRRP Commands	226
Routing Table Commands	233
Route Redistribution Commands	237
BOOTP Relay Commands	243
DNS Relay Commands	247
RIP Commands	251
DVMRP Commands	254
PIM Commands	259
IP Multicasting Commands	263
MD5 Configuration Commands	265
OSPF Configuration Commands	268
Command History List	288
Technical Specifications	290
	296
	296
	296
	296
	296
	296
	296
Copyright Statement: No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Co	296

D-Link 3312SR Reference Manual - Page 240

config route redistribute dst rip src

Page 240 highlights