D-Link 3312SR Reference Manual - Page 228

DGS-3312SR Layer 3 Gigabit Switch

222

DGS-3312SR:4#disable vrrp ping

Command: disable vrrp ping

Success.

DGS-3312SR:4#

create vrrp ipif

Purpose

To create a VRRP IP interface on the switch.

Syntax

<ipif_name 12> vrid <vrid 1-255> ipaddress <ipaddr> {state

[enable | disable] | priority <int 1-254> | advertisement_interval

<int 1-255> | preempt [true | false] | critical_ip <ipaddr> |

critical_ip_state [enable | disable]}

Description

This command is used to create a VRRP interface on the switch.

Parameters

<ipif_name 12>

- Enter the name of a previously configured IP

interface that you wish to create a VRRP entry for. This IP interface

must be assigned to a VLAN on the switch.

vrid <vrid 1-255>

- Enter a value between

1

and

255

to uniquely

identify this VRRP group on the switch. All routers participating in

this group must be assigned the same

vrid

value. This value MUST

be different from other VRRP groups set on the switch.

ipaddress <ipaddr>

- Enter the virtual IP address that will be

assigned to the VRRP entry. This IP address is also the default

gateway that will be statically assigned to end hosts and must be set

for all routers that participate in this group.

state [enable | disable]

– Used to enable and disable the VRRP IP

interface on the switch.

priority <int 1-254>

- Enter a value between 1 and 254 to indicate the

router priority. The VRRP Priority value may determine if a higher

priority VRRP router overrides a lower priority VRRP router. A higher

priority will increase the probability that this router will become the

Master router of the group. A lower priority will increase the

probability that this router will become the backup router. VRRP

routers that are assigned the same priority value will elect the

highest physical IP address as the Master router. The default value

is 100. (The value of 255 is reserved for the router that owns the IP

address associated with the virtual router and is therefore set

automatically.)

advertisement_interval <int 1-255>

- Enter a time interval value, in

seconds, for sending VRRP message packets. This value must be

consistent with all routers participating within the same VRRP group

and is used to troubleshoot poorly configured routers. The default is

1 second.

preempt [true | false]

– This entry will determine the behavior of

backup routers within the VRRP group by controlling whether a

higher priority backup router will preempt a lower priority Master

router. A

true

entry, along with having the backup router’s priority set

higher than the masters priority, will set the backup router as the

Master router. A

false

entry will disable the backup router from

becoming the Master router. This setting must be consistent with all

routers participating within the same VRRP group. The default

setting is

true

.

Section	Page
Introduction	7
	7
	7
Accessing the Switch via the Serial Port	7
Setting the Switch’s IP Address	8
Using the Console CLI	10
	10
	10
Connecting to the Switch	10
Command Syntax	16
Basic Switch Commands	18
Switch Port Commands	30
Port Security Commands	33
Network Management (SNMP) Commands	37
Switch Utility Commands	58
Network Monitoring Commands	62
Multiple Spanning Tree Protocol (MSTP) Commands	75
Forwarding Database Commands	88
Broadcast Storm Control Commands	95
QoS Commands	97
Port Mirroring Commands	105
VLAN Commands	110
Link Aggregation Commands	117
IP Commands (Including IP Multinetting)	123
IGMP Commands	128
IGMP Snooping Commands	131
MAC Notification Commands	139
Access Authentication Control Commands	143
SSH Commands	167
SSL Commands	175
802.1X Commands	180
Access Control List (ACL) Commands	192
Traffic Segmentation Commands	201
Stacking Commands	203
D-Link Single IP Management Commands	206
Time and SNTP Commands	216
ARP Commands	222
VRRP Commands	226
Routing Table Commands	233
Route Redistribution Commands	237
BOOTP Relay Commands	243
DNS Relay Commands	247
RIP Commands	251
DVMRP Commands	254
PIM Commands	259
IP Multicasting Commands	263
MD5 Configuration Commands	265
OSPF Configuration Commands	268
Command History List	288
Technical Specifications	290
	296
	296
	296
	296
	296
	296
	296
Copyright Statement: No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Co	296

D-Link 3312SR Reference Manual - Page 228

create vrrp ipif, Master router.

Page 228 highlights