D-Link 3312SR Reference Manual - Page 201

DGS-3312SR Layer 3 Gigabit Switch

195

26

T

RAFFIC

S

EGMENTATION

C

OMMANDS

Traffic segmentation allows you to further sub-divide VLANs into smaller groups of ports that will help to reduce traffic on the

VLAN.

The VLAN rules take precedence, and then the traffic segmentation rules are applied. The traffic segmentation

commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table.

Command

Parameters

config traffic_segmentation

<portlist> forward_list [null | <portlist>]

show traffic_segmentation

{<portlist>}

Each command is listed, in detail, in the following sections.

NOTE:

As a stand-alone switch or as a master switch in a switch stack,

the switch number will be referred to as 15 for all configurations, graphs

and tables.


Purpose

Used to configure traffic segmentation on the switch.

Syntax

config traffic_segmentation <portlist> forward_list [null |

<portlist>]

Description

The


command is used to configure

traffic segmentation on the switch.

Parameters

<portlist>

−

Specifies a range of ports that will be configured for

traffic segmentation. The port list is specified by listing the lowest

switch number and the beginning port number on that switch,

separated by a colon. Then the highest switch number, and the

highest port number of the range (also separated by a colon) are

specified. The beginning and end of the port list range are

separated by a dash. For example, 1:3 specifies switch number

1, port 3. 2:4 specifies switch number 2, port 4. 1:3-2:4 specifies

all of the ports between switch 1, port 3 and switch 2, port 4

−

in

numerical order.

forward_list

−

Specifies a range of ports that will receive

forwarded frames from the ports specified in the portlist, above.

null

−

no ports are specified

<portlist>

−

Specifies a range of ports for the forwarding list. This

list must be on the same switch previously specified for traffic

segmentation (i.e. following the

<portlist>

specified above for

config traffic_segmentation).

Restrictions

Only administrator-level users can issue this command.

Example usage:

To configure ports 1 through 9 to be able to forward frames to port 10 through 12:

Section	Page
Introduction	7
	7
	7
Accessing the Switch via the Serial Port	7
Setting the Switch’s IP Address	8
Using the Console CLI	10
	10
	10
Connecting to the Switch	10
Command Syntax	16
Basic Switch Commands	18
Switch Port Commands	30
Port Security Commands	33
Network Management (SNMP) Commands	37
Switch Utility Commands	58
Network Monitoring Commands	62
Multiple Spanning Tree Protocol (MSTP) Commands	75
Forwarding Database Commands	88
Broadcast Storm Control Commands	95
QoS Commands	97
Port Mirroring Commands	105
VLAN Commands	110
Link Aggregation Commands	117
IP Commands (Including IP Multinetting)	123
IGMP Commands	128
IGMP Snooping Commands	131
MAC Notification Commands	139
Access Authentication Control Commands	143
SSH Commands	167
SSL Commands	175
802.1X Commands	180
Access Control List (ACL) Commands	192
Traffic Segmentation Commands	201
Stacking Commands	203
D-Link Single IP Management Commands	206
Time and SNTP Commands	216
ARP Commands	222
VRRP Commands	226
Routing Table Commands	233
Route Redistribution Commands	237
BOOTP Relay Commands	243
DNS Relay Commands	247
RIP Commands	251
DVMRP Commands	254
PIM Commands	259
IP Multicasting Commands	263
MD5 Configuration Commands	265
OSPF Configuration Commands	268
Command History List	288
Technical Specifications	290
	296
	296
	296
	296
	296
	296
	296
Copyright Statement: No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Co	296

D-Link 3312SR Reference Manual - Page 201

Traffic Segmentation Commands, config traffic_segmentation

Page 201 highlights