D-Link 3312SR Reference Manual - Page 30

DGS-3312SR Layer 3 Gigabit Switch

24

5

S

WITCH

P

ORT

C

OMMANDS

The switch port commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the

following table.

Command

Parameters

config ports

[<portlist | all> {speed [auto | 10_half | 10_full | 100_half | 100_full |

1000_full {[master | slave]}} | flow_control [enable | disable] |

learning [enable | disable] | state [enable | disable] description

<desc 32> | clear]}

show ports

{<portlist>} {description}

Each command is listed, in detail, in the following sections.

NOTE:

As a stand-alone switch or as a master switch in a switch stack,

the switch number will be referred to as 15 for all configurations, graphs

and tables.

config ports

Purpose

Used to configure the Switch’s Ethernet port settings.

Syntax

[<portlist | all> {speed [auto | 10_half | 10_full | 100_half |

100_full | 1000_full{[master | slave]}} | flow_control [enable |

disable] | learning [enable | disable] state [enable | disable]

description <desc 32> | clear]}

Description

This command allows for the configuration of the switch’s Ethernet

ports. Only the ports listed in the

<portlist>

will be affected.

Parameters

<portlist>

−

Specifies a range of ports to be configured. The port

list is specified by listing the lowest switch number and the

beginning port number on that switch, separated by a colon. Then

the highest switch number, and the highest port number of the

range (also separated by a colon) are specified. The beginning

and end of the port list range are separated by a dash. For

example, 1:3 specifies switch number 1, port 3.

2:4 specifies

switch number 2, port 4. 1:3-2:4 specifies all of the ports between

switch 1, port 3 and switch 2, port 4

−

in numerical order.

all

−

Configure all ports on the switch.

auto

−

Enables auto-negotiation for the specified range of ports.

[10 | 100 | 1000]

−

Configures the speed in Mbps for the specified

range of ports.

[half | full]

−

Configures the specified range of ports as either full-

or half-duplex.

{[master | slave}]

−

Configures the specified range of ports as

either master or slave ports.

Section	Page
Introduction	7
	7
	7
Accessing the Switch via the Serial Port	7
Setting the Switch’s IP Address	8
Using the Console CLI	10
	10
	10
Connecting to the Switch	10
Command Syntax	16
Basic Switch Commands	18
Switch Port Commands	30
Port Security Commands	33
Network Management (SNMP) Commands	37
Switch Utility Commands	58
Network Monitoring Commands	62
Multiple Spanning Tree Protocol (MSTP) Commands	75
Forwarding Database Commands	88
Broadcast Storm Control Commands	95
QoS Commands	97
Port Mirroring Commands	105
VLAN Commands	110
Link Aggregation Commands	117
IP Commands (Including IP Multinetting)	123
IGMP Commands	128
IGMP Snooping Commands	131
MAC Notification Commands	139
Access Authentication Control Commands	143
SSH Commands	167
SSL Commands	175
802.1X Commands	180
Access Control List (ACL) Commands	192
Traffic Segmentation Commands	201
Stacking Commands	203
D-Link Single IP Management Commands	206
Time and SNTP Commands	216
ARP Commands	222
VRRP Commands	226
Routing Table Commands	233
Route Redistribution Commands	237
BOOTP Relay Commands	243
DNS Relay Commands	247
RIP Commands	251
DVMRP Commands	254
PIM Commands	259
IP Multicasting Commands	263
MD5 Configuration Commands	265
OSPF Configuration Commands	268
Command History List	288
Technical Specifications	290
	296
	296
	296
	296
	296
	296
	296
Copyright Statement: No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Co	296

D-Link 3312SR Reference Manual - Page 30

Switch Port Commands

Page 30 highlights