D-Link 3312SR Reference Manual - Page 233

DGS-3312SR Layer 3 Gigabit Switch

227

32

R

OUTING

T

ABLE

C

OMMANDS

The routing table commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the

following table.

Command

Parameters

create iproute

<network_address> <ipaddr> {<metric 1-65535>} {[primary |

backup]}

create iproute default

<ipaddr> {<metric 1-65535>}

delete iproute default

delete iproute

<network_address> <ipaddr> {[primary | backup]}

show iproute

{<network_address>} {[static | rip | ospf]}

Each command is listed, in detail, in the following sections.

create iproute

Purpose

Used to create IP route entries to the switch’s IP routing table.

Syntax

create iproute <network_address> <ipaddr> {<metric 1-

65535>} {[primary | backup]}

Description

This command is used to create a primary and backup IP route

entry to the switch’s IP routing table.

Parameters

<network_address>

−

IP address and netmask of the IP interface

that is the destination of the route. You can specify the address

and mask information using the traditional format (for example,

10.1.2.3/255.0.0.0 or in CIDR format, 10.1.2.3/8).

<ipaddr>

−

The gateway IP address for the next hop router.

<metric 1-65535>

−

Allows the entry of a routing protocol metric

entry, representing the number of routers between the Switch and

the IP address above. The default setting is 1.

[primary | backup]

- The user may choose between

Primary

and

Backup.

If the Primary Static/Default Route fails, the Backup

Route will support the entry. Please take note that the Primary

and Backup entries cannot have the same Gateway.

Restrictions

Only administrator-level users can issue this command.

Example Usage:

To add a single static address 10.48.74.121, mask 255.0.0.0 and gateway 10.1.1.254 to the routing table:

DGS-3312SR:4#create iproute 10.48.74.121/255.0.0.0 10.1.1.254 1

Command: create iproute 10.48.74.121/8 10.1.1.254 1

Success.

DGS-3312SR:4#

Section	Page
Introduction	7
	7
	7
Accessing the Switch via the Serial Port	7
Setting the Switch’s IP Address	8
Using the Console CLI	10
	10
	10
Connecting to the Switch	10
Command Syntax	16
Basic Switch Commands	18
Switch Port Commands	30
Port Security Commands	33
Network Management (SNMP) Commands	37
Switch Utility Commands	58
Network Monitoring Commands	62
Multiple Spanning Tree Protocol (MSTP) Commands	75
Forwarding Database Commands	88
Broadcast Storm Control Commands	95
QoS Commands	97
Port Mirroring Commands	105
VLAN Commands	110
Link Aggregation Commands	117
IP Commands (Including IP Multinetting)	123
IGMP Commands	128
IGMP Snooping Commands	131
MAC Notification Commands	139
Access Authentication Control Commands	143
SSH Commands	167
SSL Commands	175
802.1X Commands	180
Access Control List (ACL) Commands	192
Traffic Segmentation Commands	201
Stacking Commands	203
D-Link Single IP Management Commands	206
Time and SNTP Commands	216
ARP Commands	222
VRRP Commands	226
Routing Table Commands	233
Route Redistribution Commands	237
BOOTP Relay Commands	243
DNS Relay Commands	247
RIP Commands	251
DVMRP Commands	254
PIM Commands	259
IP Multicasting Commands	263
MD5 Configuration Commands	265
OSPF Configuration Commands	268
Command History List	288
Technical Specifications	290
	296
	296
	296
	296
	296
	296
	296
Copyright Statement: No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Co	296

D-Link 3312SR Reference Manual - Page 233

Routing Table Commands, create iproute

Page 233 highlights