D-Link 3312SR Reference Manual - Page 196

DGS-3312SR Layer 3 Gigabit Switch

190

DGS-3312SR:4#create access_profile ip vlan source_ip_mask 20.0.0.0

destination_ip_mask 10.0.0.0 dscp icmp type code permit profile_id 101

Command: create access_profile ip vlan source_ip_mask 20.0.0.0

destination_ip_mask 10.0.0.0 dscp icmp type code permit profile_id 101

Success.

DGS-3312SR

delete access_profile

Purpose

Used to delete a previously created access profile.

Syntax

delete access_profile [profile_id <value 1-255>]

Description

The

delete access_profile

command is used to delete a

previously created access profile on the switch.

Parameters

profile_id <value 1-255>

−

Enter an integer between 1 and 255 that

is used to identify the access profile that will be deleted with this

command.

This value is assigned to the access profile when it is

created with the

create access_profile

command.

Restrictions

Only administrator-level users can issue this command.

Example usage:

To delete the access profile with a profile ID of 1:

DGS-3312SR:4# delete access_profile profile_id 1

Command: delete access_profile profile_id 1

Success.

DGS-3312SR:4#

config access_profile

Purpose

Used to configure an access profile on the switch and to define

specific values that will be used to by the switch to determine if a given

packet should be forwarded or filtered. Masks entered using the

create access_profile

command will be combined, using a logical

AND operation, with the values the switch finds in the specified frame

header fields. Specific values for the rules are entered using the

config access_profile

command, below.

Syntax

<value 1-255>[ add access_id <value 1-255> [ethernet {vlan

<vlan_name 32> | source_mac <macaddr> | destination_mac

<macaddr> | 802.1p <value 0-7> | ethernet_type <hex 0x0-0xffff>

[permit {priority <value 0-7> {replace_priority }} | deny ] | ip {vlan

<vlan_name 32> | source_ip <ipaddr> | destination_ip <ipaddr> |

dscp <value 0-63> | [icmp {type <value 0-255> code <value 0-

255>} | igmp {type <value 0-255>} | tcp {src_port <value 0-65535>

Section	Page
Introduction	7
	7
	7
Accessing the Switch via the Serial Port	7
Setting the Switch’s IP Address	8
Using the Console CLI	10
	10
	10
Connecting to the Switch	10
Command Syntax	16
Basic Switch Commands	18
Switch Port Commands	30
Port Security Commands	33
Network Management (SNMP) Commands	37
Switch Utility Commands	58
Network Monitoring Commands	62
Multiple Spanning Tree Protocol (MSTP) Commands	75
Forwarding Database Commands	88
Broadcast Storm Control Commands	95
QoS Commands	97
Port Mirroring Commands	105
VLAN Commands	110
Link Aggregation Commands	117
IP Commands (Including IP Multinetting)	123
IGMP Commands	128
IGMP Snooping Commands	131
MAC Notification Commands	139
Access Authentication Control Commands	143
SSH Commands	167
SSL Commands	175
802.1X Commands	180
Access Control List (ACL) Commands	192
Traffic Segmentation Commands	201
Stacking Commands	203
D-Link Single IP Management Commands	206
Time and SNTP Commands	216
ARP Commands	222
VRRP Commands	226
Routing Table Commands	233
Route Redistribution Commands	237
BOOTP Relay Commands	243
DNS Relay Commands	247
RIP Commands	251
DVMRP Commands	254
PIM Commands	259
IP Multicasting Commands	263
MD5 Configuration Commands	265
OSPF Configuration Commands	268
Command History List	288
Technical Specifications	290
	296
	296
	296
	296
	296
	296
	296
Copyright Statement: No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Co	296

D-Link 3312SR Reference Manual - Page 196

delete access_profile

Page 196 highlights