D-Link 3312SR Reference Manual - Page 39

DGS-3312SR Layer 3 Gigabit Switch

33

create snmp user

source.

Encryption

−

Scrambles the contents of messages to prevent it

being viewed by an unauthorized source.

Parameters

<username 32>

−

An alphanumeric name of up to 32 characters

that will identify the new SNMP user.

<groupname 32>

−

An alphanumeric name of up to 32 characters

that will identify the SNMP group with which the new SNMP user

will be associated.

encrypted

– Allows the user to choose a type of authorization for

authentication using SNMP. The user may choose:

by_password auth

– Requires the SNMP user to enter a

password for authentication and privacy. The password is

defined by specifying the

auth_password

below. This method

is recommended.

•

md5

−

Specifies that the HMAC-MD5-96 authentication

level will be used. md5 may be utilized by entering the

following:

•

<auth password 8-16>

- An alphanumeric sting of

between 8 and 16 characters,used to authorize the

agent to receive packets for the host.

•

sha

−

Specifies that the HMAC-SHA-96 authentication

level will be used.

•

<auth password 8-20>

- An alphanumeric sting of

between 8 and 20 characters, used to authorize

the agent to receive packets for the host.

priv –

Adding the priv (privacy) parameter will allow for

encryption in addition to the authentication algorithm for higher

security. The user may choose:

•

des

– Adding this parameter will allow for a 56-bit

encryption to be added using the DES-56 standard

using:

•

<priv_password 8-16>

- An alphanumeric string of

between 8 and 16 characters that will be used to

encrypt the contents of messages the host sends

to the agent.

by_key auth

– Requires the SNMP user to enter an encryption key

for authentication and privacy. The key is defined by specifying the

key in hex form below. This method is not recommended.

•

md5

−

Specifies that the HMAC-MD5-96 authentication

level will be used. md5 may be utilized by entering the

following:

•

<auth_key 32-32>

- Enter an alphanumeric sting of

exactly 32 characters, in hex form, to define the

key that will be used to authorize the agent to

receive packets for the host.

•

sha

−

Specifies that the HMAC-SHA-96 authentication

level will be used.

±

<auth_key 40-40>

- Enter an alphanumeric sting

Section	Page
Introduction	7
	7
	7
Accessing the Switch via the Serial Port	7
Setting the Switch’s IP Address	8
Using the Console CLI	10
	10
	10
Connecting to the Switch	10
Command Syntax	16
Basic Switch Commands	18
Switch Port Commands	30
Port Security Commands	33
Network Management (SNMP) Commands	37
Switch Utility Commands	58
Network Monitoring Commands	62
Multiple Spanning Tree Protocol (MSTP) Commands	75
Forwarding Database Commands	88
Broadcast Storm Control Commands	95
QoS Commands	97
Port Mirroring Commands	105
VLAN Commands	110
Link Aggregation Commands	117
IP Commands (Including IP Multinetting)	123
IGMP Commands	128
IGMP Snooping Commands	131
MAC Notification Commands	139
Access Authentication Control Commands	143
SSH Commands	167
SSL Commands	175
802.1X Commands	180
Access Control List (ACL) Commands	192
Traffic Segmentation Commands	201
Stacking Commands	203
D-Link Single IP Management Commands	206
Time and SNTP Commands	216
ARP Commands	222
VRRP Commands	226
Routing Table Commands	233
Route Redistribution Commands	237
BOOTP Relay Commands	243
DNS Relay Commands	247
RIP Commands	251
DVMRP Commands	254
PIM Commands	259
IP Multicasting Commands	263
MD5 Configuration Commands	265
OSPF Configuration Commands	268
Command History List	288
Technical Specifications	290
	296
	296
	296
	296
	296
	296
	296
Copyright Statement: No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Co	296

D-Link 3312SR Reference Manual - Page 39

create snmp user, security. The user may choose

Page 39 highlights