D-Link 3312SR Reference Manual - Page 237

Route Redistribution Commands, create route redistribute dst ospf src

Page 237 highlights

DGS-3312SR Layer 3 Gigabit Switch 33 ROUTE REDISTRIBUTION COMMANDS The route redistribution commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command create route redistribute dst ospf src create route redistribute dst rip src config route redistribute dst ospf src config route redistribute dst rip src delete route redistribute show route redistribute Parameters [static | rip | local] {mettype [1 | 2] |metric } [local | static | ospf {all | internal | external | type_1 | type_2 | inter+e1 | inter+e2}] {metric } [static | rip | local] {mettype [1 | 2] |metric } [local | static | ospf {all | internal | external | type_1 | type_2 | inter+e1 | inter+e2}] {metric } {dst [rip | ospf] src [rip | local | static | ospf]} {dst [rip | ospf] | src [rip | static | local | ospf] Each command is listed, in detail, in the following sections. create route redistribute dst ospf src Purpose Syntax Description Parameters Used to add route redistribution settings for the exchange of RIP routes to OSPF routes on the switch. create route redistribute dst ospf src [static | rip | local] {mettype [1 | 2] | metric } This command will redistribute routing information between the OSPF and RIP routing protocols to all routers on the network that are running OSPF or RIP. Routing information entered into the Static Routing Table on the local DGS-3312SR switch is also redistributed. src [static | rip | local] − Allows for the selection of the protocol for the source device. Restrictions mettype [1 | 2] − Allows for the selection of one of two methods of calculating the metric value. Type-1 calculates (for RIP to OSPF) by adding the destination's interface cost to the metric entered in the Metric field. Type-2 uses the metric entered in the Metric field without change. This field applies only when the destination field is OSPF. metric − Allows the entry of an OSPF interface cost. This is analogous to a Hop Count in the RIP routing protocol. Only administrator-level users can issue this command. Routing information source − RIP. the Static Route table, and the Local interface routing information. Routing information will be redistributed to OSPF. 231

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290
  • 291
  • 292
  • 293
  • 294
  • 295
  • 296
  • 297
  • 298
  • 299
  • 300
  • 301
  • 302
  • 303
  • 304
  • 305

DGS-3312SR Layer 3 Gigabit Switch
231
33
R
OUTE
R
EDISTRIBUTION
C
OMMANDS
The route redistribution commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in
the following table.
Command
Parameters
create route redistribute
dst ospf src
[static | rip | local] {mettype [1 | 2] |metric <value>}
create route redistribute
dst rip src
[local | static | ospf {all | internal | external | type_1 | type_2 |
inter+e1 | inter+e2}] {metric <value>}
config route redistribute
dst ospf src
[static | rip | local] {mettype [1 | 2] |metric <value>}
config route redistribute
dst rip src
[local | static | ospf {all | internal | external | type_1 | type_2 |
inter+e1 | inter+e2}] {metric <value>}
delete route redistribute
{dst [rip | ospf] src [rip | local | static | ospf]}
show route redistribute
{dst [rip | ospf] | src [rip | static | local | ospf]
Each command is listed, in detail, in the following sections.
create route redistribute dst ospf src
Purpose
Used to add route redistribution settings for the exchange of RIP
routes to OSPF routes on the switch.
Syntax
create route redistribute dst ospf src [static | rip | local]
{mettype [1 | 2] | metric <value>}
Description
This command will redistribute routing information between the
OSPF and RIP routing protocols to all routers on the network that
are running OSPF or RIP. Routing information entered into the
Static Routing Table on the local DGS-3312SR switch is also
redistributed.
Parameters
src [static | rip | local]
Allows for the selection of the protocol for
the source device.
mettype [1 | 2]
Allows for the selection of one of two methods of
calculating the metric value. Type-1 calculates (for RIP to OSPF) by
adding the destination’s interface cost to the metric entered in the
Metric field. Type-2 uses the metric entered in the Metric field
without change. This field applies only when the destination field is
OSPF.
metric <value>
Allows the entry of an OSPF interface cost. This is
analogous to a Hop Count in the RIP routing protocol.
Restrictions
Only administrator-level users can issue this command.
Routing information source
RIP. the Static Route table, and the Local interface routing information.
Routing information will
be redistributed to OSPF.