D-Link 3312SR Reference Manual - Page 207

DGS-3312SR Layer 3 Gigabit Switch

201

6.

The CaS can be configured through the CS to become a MS.

After configuring one switch to operate as the CS of a SIM group, additional switches may join the group by either an automatic

method or by manually configuring the switch to be a MS. The CS will then serve as the in band entry point for access to the

MS. The CS’s IP address will become the path to all MS’s of the group and the CS’s Administrator’s password, and/or

authentication will control access to all MS’s of the SIM group.

With SIM enabled, the applications in

the CS will redirect the packet instead of executing the packets. The applications will

decode the packet from the administrator, modify some data, and then send it to the MS. After execution, the CS may receive a

response packet from the MS, which it will encode and send it back to the administrator.

When a CS becomes a MS, it automatically becomes a member of first SNMP community (include read/write and read only) to

which the CS belongs. However, if a MS has its own IP address, it can belong to SNMP communities to which other switches in

the group, including the CS, do not belong.

The SIM commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following

table.

Command

Parameters

enable sim

disable sim

show sim

{[candidates {<candidate_id 1-32>} | members {<member_id 1-

32>} | group {commander_mac <macaddr>} | neighbor]}

reconfig

{member_id <value 1-32> | exit}

config sim_group

[add <candidate_id 1-32> {<password>} | delete <member_id 1-

32>]

config sim

[{[commander {group_name <groupname 64> | candidate] |

dp_interval <sec 30-90> | hold_time <sec 100-255>}

download sim_ms

[firmware | configuration] <ipaddr> <path_filename> [members

<mslist> | all}

upload sim_ms

[configuration] <ipaddr> <path_filename> <member_id 1-32>

Each command is listed, in detail, in the following sections.

enable sim

Purpose

Used to enable Single IP Management (SIM) on the switch

Syntax

enable sim

Description

This command will enable SIM globally on the switch. SIM features

and functions will not function properly unless this function is

enabled.

Parameters

None.

Restrictions

Only administrator-level users can issue this command.

Example usage:

To enable SIM on the switch:

DGS-3312SR:4#enable sim

Command: enable sim

Success.

DGS-3312SR:4#

Section	Page
Introduction	7
	7
	7
Accessing the Switch via the Serial Port	7
Setting the Switch’s IP Address	8
Using the Console CLI	10
	10
	10
Connecting to the Switch	10
Command Syntax	16
Basic Switch Commands	18
Switch Port Commands	30
Port Security Commands	33
Network Management (SNMP) Commands	37
Switch Utility Commands	58
Network Monitoring Commands	62
Multiple Spanning Tree Protocol (MSTP) Commands	75
Forwarding Database Commands	88
Broadcast Storm Control Commands	95
QoS Commands	97
Port Mirroring Commands	105
VLAN Commands	110
Link Aggregation Commands	117
IP Commands (Including IP Multinetting)	123
IGMP Commands	128
IGMP Snooping Commands	131
MAC Notification Commands	139
Access Authentication Control Commands	143
SSH Commands	167
SSL Commands	175
802.1X Commands	180
Access Control List (ACL) Commands	192
Traffic Segmentation Commands	201
Stacking Commands	203
D-Link Single IP Management Commands	206
Time and SNTP Commands	216
ARP Commands	222
VRRP Commands	226
Routing Table Commands	233
Route Redistribution Commands	237
BOOTP Relay Commands	243
DNS Relay Commands	247
RIP Commands	251
DVMRP Commands	254
PIM Commands	259
IP Multicasting Commands	263
MD5 Configuration Commands	265
OSPF Configuration Commands	268
Command History List	288
Technical Specifications	290
	296
	296
	296
	296
	296
	296
	296
Copyright Statement: No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Co	296

D-Link 3312SR Reference Manual - Page 207

enable sim, DGS-3312SR:4#enable sim, Command: enable sim, Success., DGS-3312SR:4

Page 207 highlights