D-Link 3312SR Reference Manual - Page 37

DGS-3312SR Layer 3 Gigabit Switch

31

7

N

ETWORK

M

ANAGEMENT

(SNMP) C

OMMANDS

The DGS-3312SR supports the Simple Network Management Protocol (SNMP) versions 1, 2c, and 3. You can specify which

version of the SNMP you want to use to monitor and control the switch. The three versions of SNMP vary in the level of

security provided between the management station and the network device. The following table lists the security features of the

three SNMP versions:

The network management commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in

the following table.

SNMP Version

Authentication Method

Description

v1

Community String

Community String is used for authentication

−

NoAuthNoPriv

v2c

Community String

Community String is used for authentication

−

NoAuthNoPriv

v3

Username

Username is used for authentication

−

NoAuthNoPriv

v3

MD5 or SHA

Authentication is based on the HMAC-MD5 or HMAC-SHA

algorithms

−

AuthNoPriv

v3

MD5 DES or SHA DES

Authentication is based on the HMAC-MD5 or HMAC-SHA

algorithms

−

AuthPriv.

DES 56-bit encryption is added based on the CBC-DES

(DES-56) standard

Each command is listed, in detail, in the following sections.

Command

Parameters

create snmp user

create snmp user <username 32> <groupname 32> {encrypted

[by_password auth [md5 <auth_password 8-16> | sha

<auth_password 8-20 >] priv [none | des <priv_password 8-16>] |

by_key auth [md5 <auth_key 32-32> | sha <auth_key 40-40>] priv

[none | des <priv_key 32-32>]]}

delete snmp user

<username 32>

show snmp user

create snmp view

<view_name 32> <oid> view_type [included | excluded]

delete snmp view

<view_name 32> [all | oid]

show snmp view

<view_name 32>

create snmp

community

<community_string 32> view <view_name 32> [read_only |

read_write]

delete snmp

community

<community_string 32>

show snmp

community

<community_string 32>

config snmp engineID

<snmp_engineID>

show snmp engineID

Section	Page
Introduction	7
	7
	7
Accessing the Switch via the Serial Port	7
Setting the Switch’s IP Address	8
Using the Console CLI	10
	10
	10
Connecting to the Switch	10
Command Syntax	16
Basic Switch Commands	18
Switch Port Commands	30
Port Security Commands	33
Network Management (SNMP) Commands	37
Switch Utility Commands	58
Network Monitoring Commands	62
Multiple Spanning Tree Protocol (MSTP) Commands	75
Forwarding Database Commands	88
Broadcast Storm Control Commands	95
QoS Commands	97
Port Mirroring Commands	105
VLAN Commands	110
Link Aggregation Commands	117
IP Commands (Including IP Multinetting)	123
IGMP Commands	128
IGMP Snooping Commands	131
MAC Notification Commands	139
Access Authentication Control Commands	143
SSH Commands	167
SSL Commands	175
802.1X Commands	180
Access Control List (ACL) Commands	192
Traffic Segmentation Commands	201
Stacking Commands	203
D-Link Single IP Management Commands	206
Time and SNTP Commands	216
ARP Commands	222
VRRP Commands	226
Routing Table Commands	233
Route Redistribution Commands	237
BOOTP Relay Commands	243
DNS Relay Commands	247
RIP Commands	251
DVMRP Commands	254
PIM Commands	259
IP Multicasting Commands	263
MD5 Configuration Commands	265
OSPF Configuration Commands	268
Command History List	288
Technical Specifications	290
	296
	296
	296
	296
	296
	296
	296
Copyright Statement: No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Co	296

D-Link 3312SR Reference Manual - Page 37

Network Management (SNMP) Commands - des

Page 37 highlights