D-Link 3312SR Reference Manual - Page 219

DGS-3312SR Layer 3 Gigabit Switch

213

To manually set system time and date settings:

DGS-3312SR:4#config time 30jun2003 16:30:30

Command: config time 30jun2003 16:30:30

Success.

DGS-3312SR:4#

config time zone

Purpose

Used to determine the time zone used in order to adjust the

system clock.

Syntax

config time_zone {operator [+ | -] | hour <gmt_hour 0-13> |

min <minute 0-59>}

Description

This will adjust system clock settings according to the time zone.

Time zone settings will adjust SNTP information accordingly.

Parameters

operator

– Choose to add (+) or subtract (-) time to adjust for time

zone relative to GMT.

hour

– Select the number hours different from GMT.

min

– Select the number of minutes difference added or

subtracted to adjust the time zone.

Restrictions

Only administrator-level users can issue this command.

Example usage:

To configure time zone settings:

DGS-3312SR:4#config time_zone operator + hour 2 min 30

Command: config time_zone operator + hour 2 min 30

Success.

DGS-3312SR:4#

config dst

Purpose

Used to enable and configure time adjustments to allow for the use of

Daylight Savings Time (DST).

Syntax

config dst [disable | repeating {s_week <start_week 1-4,last> |

s_day <start_day sun-sat>| s_mth <start_mth 1-12> | s_time

<start_time hh:mm> | e_week <end_week 1-4,last> | e-day

<end_day sun-sat> | e_mth <end_mth 1-12> | e_time <end_time

hh:mm> | offset [30 | 60 | 90 | 120]} | annual

{s_date <start_date

1-31> | s_mth <start_mth 1-12> | s_time <start_time hh:mm> |

e_date <end_date 1-31> | e_mth <end_mth 1-12> | e_time

<end_time hh:mm> | offset [30 | 60 | 90 | 120]}]

Description

DST can be enabled and configured using this command. When

enabled this will adjust the system clock to comply with any DST

requirement. DST adjustment effects system time for both manually

configured time and time set using SNTP service.

Section	Page
Introduction	7
	7
	7
Accessing the Switch via the Serial Port	7
Setting the Switch’s IP Address	8
Using the Console CLI	10
	10
	10
Connecting to the Switch	10
Command Syntax	16
Basic Switch Commands	18
Switch Port Commands	30
Port Security Commands	33
Network Management (SNMP) Commands	37
Switch Utility Commands	58
Network Monitoring Commands	62
Multiple Spanning Tree Protocol (MSTP) Commands	75
Forwarding Database Commands	88
Broadcast Storm Control Commands	95
QoS Commands	97
Port Mirroring Commands	105
VLAN Commands	110
Link Aggregation Commands	117
IP Commands (Including IP Multinetting)	123
IGMP Commands	128
IGMP Snooping Commands	131
MAC Notification Commands	139
Access Authentication Control Commands	143
SSH Commands	167
SSL Commands	175
802.1X Commands	180
Access Control List (ACL) Commands	192
Traffic Segmentation Commands	201
Stacking Commands	203
D-Link Single IP Management Commands	206
Time and SNTP Commands	216
ARP Commands	222
VRRP Commands	226
Routing Table Commands	233
Route Redistribution Commands	237
BOOTP Relay Commands	243
DNS Relay Commands	247
RIP Commands	251
DVMRP Commands	254
PIM Commands	259
IP Multicasting Commands	263
MD5 Configuration Commands	265
OSPF Configuration Commands	268
Command History List	288
Technical Specifications	290
	296
	296
	296
	296
	296
	296
	296
Copyright Statement: No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Co	296

D-Link 3312SR Reference Manual - Page 219

config time zone, config dst, Daylight Savings Time DST.

Page 219 highlights