Dell PowerConnect 6024 Command Line Interface (CLI) Guide (.htm)
Dell PowerConnect 6024 Manual
View all Dell PowerConnect 6024 manuals
Add to My Manuals
Save this manual to your list of manuals |
Dell PowerConnect 6024 manual content summary:
- Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 1
Dell™ PowerConnect™ 6024/6024F Systems CLI Reference Guide www.dell.com | support.dell.com - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 2
in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. Trademarks used in this text: Dell, the DELL logo, and PowerConnect are trademarks of Dell Inc. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 3
Image Files Commands 30 DHCP Relay Commands 30 Ethernet Configuration Commands 30 GVRP Commands 31 IGMP Snooping Commands 33 IP Addressing 33 IP Routing 34 LACP Commands 35 Line Commands 35 Management ACL Commands 35 Multicast Routing 36 OSPF 36 PHY Diagnostics Commands 38 Port Channel - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 4
45 VLAN Commands 46 VRRP Commands 47 Web Server Commands 47 802.1x Commands 48 2 Using the CLI CLI Command Modes 49 Starting the CLI 53 Editing Features 53 3 AAA Commands aaa authentication login 57 aaa authentication enable 58 login authentication 59 enable authentication 60 ip http - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 5
68 aaa login-history file 69 set username active 69 set line active 70 set enable-password active 71 show authentication methods 71 show users accounts 72 show passwords configuration 73 show users login-history 75 4 ACL Commands ip access-list 77 permit (IP 77 deny (IP 79 mac access-list - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 6
Table Commands bridge address 87 bridge multicast filtering 88 bridge multicast address 88 bridge multicast forbidden address 89 bridge multicast forward-all 90 bridge multicast forbidden forward-all 91 bridge aging-time 92 clear bridge 93 port security 93 port security routed secure - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 7
client poll 109 sntp server 109 show clock 110 show sntp configuration 112 show sntp status 113 7 DHCP Relay Commands ip dhcp relay enable 115 ip dhcp relay address 115 show ip dhcp relay 116 8 Configuration and Image Files configure 117 copy 117 delete startup-config 121 boot system 121 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 8
counters 137 set interface active 137 show interfaces configuration 138 show interfaces status 140 show interfaces description 142 show interfaces counters 143 show ports jumbo-frame 146 port storm-control include-multicast 147 port storm-control broadcast enable 147 port storm-control - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 9
forbid 154 clear gvrp statistics 154 show gvrp configuration 155 show gvrp statistics 157 show gvrp error-statistics 157 11 IP Addressing Commands ip address 159 ip address dhcp 160 ip default-gateway 161 show ip interface 161 arp 162 arp timeout 163 ip proxy-arp 164 clear arp-cache 164 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 10
snooping host-time-out 176 ip igmp snooping mrouter-time-out 177 ip igmp snooping leave-time-out 178 show ip igmp snooping mrouter 178 show ip igmp snooping interface 179 show ip igmp snooping groups 180 13 IP Routing Protocol-Independent Commands interface ip 183 ip route 183 key-chain 184 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 11
14 LACP Commands lacp system-priority 197 lacp port-priority 197 lacp timeout 198 show lacp ethernet 198 show lacp port-channel 199 15 Line Commands line 201 speed access-class 211 17 Multicast Routing Commands ip multicast-routing 213 ip dvmrp 213 ip dvmrp metric 214 Contents 11 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 12
group 219 show ip mroute 219 show ip mroute-next-hop 222 show ip dvmrp interface 223 show ip dvmrp neighbor 224 show ip dvmrp next-hop 226 show ip dvmrp route 227 show ip dvmrp prune 228 show ip igmp interface 229 show ip igmp groups 230 18 OSPF Commands router ospf enable 233 router ospf - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 13
area default-cost 242 ospf 243 ospf enable 244 ip ospf process 251 show ip ospf 252 show ip ospf virtual-links 253 show ip ospf database 254 show ip ospf interface 267 show ip ospf neighbor 268 19 PHY Diagnostics Commands test copper-port tdr 271 show copper-ports tdr 272 show copper-ports - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 14
20 Port Channel Commands interface port-channel 277 interface range port-channel 277 channel-group 278 show interfaces port-channel 279 21 Port Monitor Commands port monitor 281 port monitor vlan-tagging 282 show ports monitor 283 22 QoS Commands qos 285 show qos 285 priority-queue out num- - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 15
310 police 311 police aggregate 312 trust 313 set 314 service-policy 314 23 Radius Commands radius-server host 317 radius-server key 318 radius-server retransmit 319 radius-server source-ip 319 radius-server timeout 320 radius-server deadtime 320 show radius-servers 321 Contents 15 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 16
24 RIP Commands router rip enable 323 router rip redistribute ospf 323 router rip redistribute static 324 rip 324 rip passive-interface 325 rip auto-send 325 rip version 326 rip offset 327 rip default-route originate 327 rip default-route offset 328 rip authentication 329 show ip rip 330 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 17
26 SNMP Commands SNMP General Commands 349 SNMPv1/v2 Commands 360 SNMPv3 Commands 363 27 28 Spanning-Tree Commands spanning-tree 369 spanning-tree mode 369 spanning-tree forward- 392 spanning-tree mst max-hops 393 spanning-tree mst port-priority 393 spanning-tree mst cost 394 Contents 17 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 18
mst configuration 395 instance (mst 396 name (mst 396 revision (mst 397 show (mst 398 exit (mst 399 abort (mst 399 29 SSH Commands ip ssh port 401 ip ssh server 401 crypto key generate dsa 402 crypto key generate rsa 402 ip ssh pubkey-auth 403 crypto key pubkey-chain ssh 404 user-key - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 19
show logging file 420 show syslog-servers 422 31 System Management ping 423 reload 424 clock set 425 hostname 426 asset-tag 426 show users 427 show clock 427 show system 428 show version 430 show system id 430 traceroute 431 telnet 434 resume 437 32 TACACS+ Commands tacacs-server host - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 20
tacacs-server source-ip 440 tacacs-server timeout 441 show tacacs 442 33 User Interface enable 445 disable 445 login 446 exit(configuration 446 exit(EXEC 447 end 447 help 448 history 448 history size 449 debug-mode 450 show history 450 show privilege 451 34 VLAN Commands vlan database - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 21
463 show vlan 464 show vlan internal usage 465 show vlan protocols-groups 466 show interfaces switchport 467 35 VRRP Commands vrrp ip 469 vrrp up 469 vrrp timer 470 vrrp priority 471 vrrp source-ip 472 vrrp authentication 472 vrrp preempt 473 show vrrp configuration 473 show vrrp status - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 22
36 Web Server ip http port 477 ip http server 477 ip https port 478 ip https server 478 crypto certificate generate 479 crypto certificate request 480 crypto certificate import 482 ip https certificate 483 show ip http 484 show ip https 484 37 802.1x Commands aaa authentication dot1x 487 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 23
dot1x auth-not-req 500 dot1x multiple-hosts 501 dot1x single-host-violation 501 show dot1x advanced 502 Contents 23 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 24
24 Contents - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 25
also provides information for configuring the PowerConnect switch, details the procedures and provides configuration examples. Basic installation configuration is described in the User's Guide and must be completed before using this document. Command Groups The system commands can be broken down - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 26
www.dell.com | support.dell.com Line Management ACL Multicast Routing OSPF PHY Diagnostics Port Channel Port Monitor QoS RADIUS RIP RMON SNMP Spanning Tree SSH Syslog Commands System Management TACACS+ User Interface VLAN VRRP Web Server 802.1x Configures the console and remote Telnet connection. - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 27
authentication ip http authentication ip https authentication password enable password username passwords min-length password-aging passwords aging passwords history passwords history hold-time passwords history hold-time aaa login-history file set username active set line active set enable-password - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 28
www.dell.com | support.dell.com ACL Commands Command Group ip access-list permit (IP) deny (IP) mac access-list permit (MAC) deny (MAC) service-acl show access-lists show interfaces access-lists Description Mode Creates IP ACLs, and enters to IP- GC Access list configuration mode. Allows - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 29
enable sntp unicast client poll sntp server show clock Description Configures an external time source to maintain the system clock Defines the time zone for display purposes Configures the system clock to automatically switch to Daylight Savings Time Defines an authentication key for SNTP Set - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 30
dell.com | support.dell.com show sntp configuration Displays the SNTP configuration PE show sntp status Displays the SNTP status PE Configuration and Image Files Commands Command Group configure copy delete startup-config boot system show running-config show startup-config show backup-config - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 31
ports jumbo-frame port storm-control includemulticast port storm-control broadcast enable port storm-control broadcast rate show ports storm-control show interfaces advertise GVRP Commands Command Group gvrp enable (global) gvrp enable (interface) garp timer gvrp vlan-creation-forbid Configures - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 32
www.dell.com | support.dell.com gvrp registration-forbid clear gvrp statistics show gvrp configuration show gvrp statistics show gvrp error-statistics De-registers all VLANs, and prevents dynamic VLAN registration on IC the port. Clears all the GVRP statistics information. GC Displays GVRP - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 33
interface show ip igmp snooping groups Description Enables Internet Group Management Protocol (IGMP) snooping. Enables Internet Group Management Protocol (IGMP) snooping on a specific VLAN. Enables automatic learning of multicast router ports in the context of a specific VLAN. Configures the host - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 34
www.dell.com | support.dell.com ip domain-name ip name-server ip host clear host clear host dhcp show hosts Defines a default domain name to complete unqualified host names. GC Configures available name servers GC Configures static host name-to-address mapping in the host cache GC Deletes - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 35
history size show line Description Identifies a specific line for configuration and enters the line configuration command mode. Sets the line baud rate. Configures the interval that the system waits until user input is detected. Enables the command history function for the current terminal session - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 36
www.dell.com | support.dell.com Multicast Routing Command Group ip multicast-routing ip dvmrp ip dvmrp metric ip igmp ip igmp query-interval ip igmp last-member-queryinterval ip igmp query-max-responsetime ip igmp version ip igmp static-group show ip mroute show ip mroute-next-hop show ip dvmrp - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 37
virtual-links Enables advertisements of directly connected networks routes, running GC OSPF. Defines an OSPF virtual link and enters the OSPF Virtual-link GC Configuration mode. Specifies the interval between hello packets that the software sends on OV the OSPF virtual link interface. Sets the - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 38
mode of a specific port-channel. Enters the interface configuration mode to configure multiple portchannels. Associates a port with a port-channel. Displays port-channel information. Mode GC GC IC PE Port Monitor Commands Command Group port monitor port monitor vlan-tagging show ports monitor - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 39
. Displays the QoS status. Enables the egress queues to be expedite queues. Mode GC UE GC Sets a shaper on an egress port/queue. IC Assigns the tail-drop mechanism on an egress queue and configures GC the tail-drop thresholds. Assigns Weighted Round Robin (WRR) weights to egress queues. IC - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 40
PM map. Configures the trust state. PM Sets new values in the IP packet. PM Applies a policy map to the interface input. IC Radius Commands Command Group radius-server host radius-server key radius-server retransmit radius-server source-ip radius-server timeout radius-server deadtime show - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 41
table. Configures the maximum RMON tables sizes. Mode UE IC UE UE GC UE UE GC UE UE GC SNMP Commands Command Group snmp-server community snmp-server contact snmp-server location snmp-server enable traps snmp-server trap authentication snmp-server host snmp-server set Description Sets up the - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 42
www.dell.com | support.dell.com snmp-server user snmp-server group snmp-server user snmp-server v3-host snmp-server filter snmp-server v3-host show snmp show snmp engineID show snmp users show snmp groups show snmp filters show snmp users Creates or updates an SNMP server view entry. Configures a - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 43
. Enables public key authentication for incoming SSH sessions. Enters SSH Public Key-chain configuration mode. Specifies which SSH public key is manually configured and enters the SSH public key-string configuration command. Manually specifies a SSH public key. Displays the SSH server configuration - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 44
www.dell.com | support.dell.com Syslog Commands Command Group logging on logging logging console logging buffered logging buffered size clear logging logging file clear logging file aaa logging file-system logging management logging show logging show logging file show syslog-servers Description - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 45
IP address used for communication with TACACS+ servers. Sets the interval for which the switch waits for a server host to reply. Displays TACACS+ server settings and statistics. Mode GC GC GC GC PE User Interface Commands Command Group enable disable login exit(configuration) exit(EXEC) end help - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 46
be VC used for protocol-based VLAN assignment. Sets a protocol-based classification rule. IC Displays VLAN information. PE Displays a list of VLANs being used internally by the switch. PE Displays protocols-groups information. PE Displays switchport configuration. PE 46 Command Groups - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 47
Command Group ip http port ip http server ip https port ip https server crypto certificate generate crypto certificate request crypto certificate import ip https certificate show ip http show ip https Description Specifies the TCP port for use by a web browser to configure the device. Enables - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 48
. Displays 802.1x statistics for the specified interface. Enables unauthorized devices to access that VLAN. Allows multiple hosts (clients) on an 802.1x-authorized port where the dot1x port-control interface configuration command is set to auto. Configures the action to be taken when a station with - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 49
Interface Configuration mode. The following figure illustrates the command mode access path. User EXEC Mode Prompt: console> Enable Password Global ConfigurationMode Prompt: console(config)# Privileged Mode Prompt: console# Layer2 Interface Ethernet Prompt: console(config-if )# Interface VLAN - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 50
by the angle bracket (>). Console> The default host name is "Console" unless it has been changed using the hostname command in the Global Configuration mode. Privileged EXEC Mode Because many of the privileged commands set operating parameters, privileged access is password protected to prevent - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 51
mode to Privileged EXEC mode, the user can use one of the following commands: • exit • end • Ctrl+Z The following example illustrates how to access the Global Configuration mode and return to the Privileged EXEC mode: Console# Console#configure Console(config)#exit Console# Using the CLI 51 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 52
the Management Access List Configuration mode. • Policy-map Class-Contains commands to configure QoS packet properties. The overall set of classification rules and their corresponding action (meter, security) are assigned to a specific port. The Global Configuration mode command policy-map class is - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 53
to enter the key-chain configuration mode. • Global Configuration mode command interface ip is used to enter the Interface IP Configuration mode. Starting the CLI The switch can be managed over a direct connection to the switch console port, or via a Telnet connection. The switch can also be managed - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 54
after the command keyword. For example, to set a password for the administrator, enter: Console(config)# username admin password smith When working with the CLI, the command options are not displayed. The command is not selected by a menu but is manually entered. To see what commands are available - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 55
the Effect of Commands For many configuration commands, the prefix keyword no can be entered to cancel the effect of a command or reset the configuration to the default value. This guide describes the negation effect for all applicable commands. Command Completion If a command is entered and - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 56
www.dell.com | support.dell.com CLI Command Conventions When entering commands there are certain command entry standards which apply to all commands. The following table describes the command conventions. Convention [ ] { } Italic font Ctrl+F4 Screen Display all Description In a command - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 57
authentication. radius Uses the list of all RADIUS servers for authentication. Default Configuration The local user database is checked. This has the same effect as the command aaa authentication login list-name local. NOTE: On the console, login succeeds without any authentication check if the - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 58
Radius authentication. Example The following example configures authentication login. Console (config)# aaa authentication login default radius local enable none aaa authentication enable The aaa authentication enable global configuration command defines authentication method lists for accessing - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 59
command aaa authentication enable default enable. On the console, the enable password is used if it exists. If no password is set, the process still succeeds. This has the same effect as using the command aaa authentication enable default enable none. Command Mode Global Configuration mode User - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 60
The following example specifies the default authentication method for a remote Telnet or console. Console (config)# line console Console (config-line)# login authentication default enable authentication The enable authentication line configuration command specifies the authentication method list - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 61
or console. Console (config)# line console Console (config-line)# enable authentication default ip http authentication The ip http authentication global configuration mode command specifies authentication methods for http. To return to the default, use the no form of this command. Syntax ip http - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 62
| support.dell.com Example The following example configures the http authentication. Console (config)# ip http authentication radius local ip https authentication The ip https authentication global configuration command specifies authentication methods for https servers. To return to the default - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 63
mode User Guidelines If an encrypted password is specified on a line, the required password length is 32 characters. Example The following example specifies a password "dell" on a line. Console (config-line)# password dell enable password The enable password global configuration command sets a local - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 64
The following example defines local level 15 password "dell" to control access to user and privilege levels. Console (config)# enable password level 15 dell username The username global configuration command establishes a username-based authentication system. To remove a user name use the no form of - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 65
: 8-64). Default Configuration No minimum password length. Command Mode Global Configuration mode User Guidelines Relevant to local user passwords, line passwords and enable passwords. The software checks the password length when an unencrypted password is defined or a user enters a password when - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 66
aging to 120 days. Console (config)# line telnet Console (config-line)# password-aging 120 passwords aging The passwords aging global configuration command configures the expiration time of local username and enable passwords in the local database. To return to the default configuration, use the no - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 67
the user still does not change the password, the account is locked. Example The following example configures the password expiration time of username "bob" to 120 days. Console (config)# passwords aging username bob 120 passwords history The passwords history global configuration command configures - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 68
support.dell.com Command Mode Global Configuration mode User Guidelines Relevant to local user passwords, line passwords and enable passwords. Password history is not checked during the configuration download. Password history is saved even if the the feature is disabled. A user's password history - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 69
to the login history file is enabled. Command Mode Global Configuration mode User Guidelines The login history is also saved in the internal buffer of the device. Example The following example enables writing to the login history file. Console (config)# aaa login-hisory file set username active The - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 70
www.dell.com | support.dell.com Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example reactivates a suspended user with username "bob". Console # set username - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 71
(Range: 1 -15). Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example reactivates a locked local level 15 password. Console # set enable-password 15 active show - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 72
Method Lists Default : Enable admin : Enable Line ------Console Telnet SSH Login Method List Default Default Default Enable Method List Default Default Default http https : None : None show users accounts The show users accounts privileged EXEC command displays information - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 73
command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays the local users configured with access to the system. Console# show users accounts Username Privilege Password Aging Password - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 74
.dell.com | support.dell.com Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays information about password management in the local database. Console - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 75
of a specific line password. show users login-history The show users login-history privileged EXEC command displays information about the login history of users. Syntax show users login-history [username name] • name-Name of the user. (Range: 1-20 characters) Default Configuration This command has - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 76
www.dell.com | support.dell.com Example The following example displays the login history of users. Console # show users login-history Login Robert John Betty Protocol -------HTTP HTTP Serial HTTP SSH Telnet Location -------172.16.1.8 172.16.0.8 172.16.0.8 172.16.0.1 172.16.1.7 76 AAA Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 77
service-acl command). The ip access-list command enters the IP-access list configuration mode. Example The following example creates an ACL with the name "Dell". Console (config)# ip access-list Dell Console (config-ip-al)# permit (IP) The permit ip access-list configuration mode command allows - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 78
-Matches dscp number with the packet DSCP value. • precedence-Matches ip-precedence with the packet ip-precedence value. Default Configuration This command has no default configuration. Command Mode IP Access-list Configuration mode User Guidelines When an access control entry (ACE) is added to an - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 79
and DSCP 56. Console (config)# ip access-list Dell Console (config-ip-al)# permit rsvp 12.1.1.1 0.0.0.0 any dscp 56 deny (IP) The deny IP access-list configuration command denies traffic if the conditions defined in the deny statement are matched. Syntax deny [disable-port] {any| protocol} {any - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 80
dell.com | support.dell.com • source-port-Specifies the UDP/TCP source port. Use any for all ports. • dscp-Matches dscp number with the packet DSCP value. • precedence-Matches ip-precedence with the packet ip-precedence value. Default Configuration This command has no default configuration. Command - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 81
(using service-acl command). MAC named lists are used with VLAN maps and class maps. Entering the mac access-list command enables the MAC-access list configuration mode. Example The following example creates a MAC ACL with the name "dell". Console (config)# mac access-list dell Console (config-mac - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 82
www.dell.com | support.dell.com User Guidelines When an access control entry (ACE) is added :66 with any destination on VLAN 4. Console (config-mac-al)# permit 66:66:66:66:66:66 00:00:00:00:00:00 any vlan 4 deny (MAC) The deny mac-acl configuration mode command denies traffic if the conditions - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 83
to a VLAN interface. Example The following example configures a MAC ACE to deny traffic from MAC address 6:6:6:6:6:6. Console (config)# mac access-list dell Console (config-mac-al)# deny 06:06:06:06:06:06 00:00:FF:FF:FF:FF any service-acl The service-acl interface configuration command applies an - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 84
| support.dell.com show access-lists The show access-lists privileged EXEC command displays access control lists (ACLs) defined on the switch. Syntax show access-lists [name] • name-The ACL name. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 85
-VLAN number. • port-channel-number-port-channel index. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Examples The following example displays an ACL configured on the device. Console - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 86
www.dell.com | support.dell.com 86 ACL Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 87
unlock learning (no port security command). This parameter is only available when the port is in learning locked mode. Default Configuration No static addresses are defined. The default mode for an added address is permanent. Command Mode Interface configuration (VLAN) mode User Guidelines There are - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 88
address 3aa2.64b3.a245 on port g8 to the bridge table. Console (config)# interface vlan 2 Console (config-vlan)# bridge address 3aa2.64b3.a245 ethernet g8 permanent bridge multicast filtering The bridge multicast filtering global configuration command enables filtering of Multicast addresses. To - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 89
. Console (config)# interface vlan 8 Console (config-if)# bridge multicast address 0100.5e02.0203 add ethernet g1-9, g2 bridge multicast forbidden address The bridge multicast forbidden address interface configuration command forbids adding a specific Multicast address to specific ports. Address - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 90
address 0100.5e02.0203 Console (config-if)# bridge multicast forbidden address 0100.5e02.0203 add ethernet g9 bridge multicast forward-all The bridge multicast forward-all interface configuration command enables forwarding of all Multicast packets on a port. To restore the default, use the no form - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 91
. Console (config)# interface vlan 2 Console (config-if)# bridge multicast forward-all add ethernet g8 bridge multicast forbidden forward-all The bridge multicast forbidden forward-all interface configuration command forbids a port to be a forward-all-Multicast port. To restore the default, use - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 92
.dell.com | support.dell.com Default Configuration By default, this setting is disabled (for example, forwarding to the port is not forbidden). Command Mode Interface Configuration (VLAN) mode User Guidelines IGMP snooping dynamically discovers Multicast router ports. When a Multicast router port - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 93
This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example In this example, the bridge tables are cleared. Console# clear bridge port security The port security interface configuration command locks the port. By - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 94
forwarding is enabled without learning, and with traps sent every 100 seconds on port g1. Console (config)# interface ethernet g1 Console (config-if)# port security forward trap 100 port security routed secure-address The port security routed secure-address interface configuration command adds MAC - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 95
[vlan vlan] [ethernet interface | port-channel port-channelnumber] • vlan-Specific valid VLAN, such as VLAN 1. • interface-A valid Ethernet port. • port-channel-number-A valid port-channel number. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 96
[vlan vlan] [ethernet interface | port-channel port-channelnumber] • vlan-Specific valid VLAN, such as VLAN 1. • interface-A valid Ethernet port. • port-channel-number-A valid port-channel number. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 97
vlan_id-A VLAN ID value. • mac-multicast-address-A MAC Multicast address. • ip- multicast-address-An IP Multicast address. • format-Multicast address format. Can be ip or mac. If format is unspecified, the default is mac. Default Configuration This command has no default configuration. Command Mode - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 98
the Multicast filtering configuration. Syntax show bridge multicast filtering vlan-id • vlan_id-A valid VLAN ID value. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. 98 Address Table - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 99
for VLAN 1 is displayed. Console # show bridge multicast filtering 1 Filtering: Enabled VLAN: 1 Port Forward-All Static Status ---- ------ ------ g1 Forbidden Filter g2 Forward Forward(s) g3 - Forward(s) show ports security The show ports security privileged EXEC command displays - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 100
dell.com | support.dell.com Example In this example, all classes of entries in the port-lock status are displayed. Console # show ports security Port - - - - ch4 Unlocked - - - - ch5 Unlocked - - - - ch6 Unlocked - - - - ch7 Unlocked - - - - 100 Address Table Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 101
User Guidelines Time from the external time source is acquired using the Simple Network Time Protocol (STNP). Examples The following example configures an external time source for the system clock. Console(config)# clock source sntp clock timezone The clock timezone global configuration command sets - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 102
com | support.dell.com Command Mode Global Configuration mode User Guidelines The system internally keeps time in UTC, so this command is used only for display purposes and when the time is manually set. Examples The following example sets the timezone to 6 hours difference from UTC. Console(config - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 103
example sets summer time starting on the first Sunday in April at 2 am and finishing on the last Sunday in October at 2 am. Console(config)# clock summer-time recurring first sun apr 2:00 last sun oct 2:00 sntp authentication-key The sntp authentication-key global configuration command defines - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 104
) Default Configuration No authentication key is defined. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Examples The following example defines the authentication key for SNTP. Console(config)# sntp authentication-key 8 md5 ClkKey Console(config - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 105
be trusted. (Range: 1 - 4294967295) Default Configuration No keys are trusted. Command Mode Global Configuration mode User Guidelines This command is relevant for both received Unicast and Broadcast. Examples The following example authenticates key 8. Console(config)# sntp authentication-key 8 md5 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 106
no user guidelines for this command. Examples The following example sets the polling time for the Simple Network Time Protocol (SNTP) client to 120 seconds. Console(config)# sntp client poll timer 120 sntp broadcast client enable The sntp broadcast client enable global configuration command enables - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 107
Configuration mode User Guidelines Polling time is determined by the sntp client poll timer global configuration command. Use the sntp client enable interface configuration command to enable SNTP clients on a specific interface. Examples The following example enables Anycast clients. Console(config - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 108
.dell.com | support.dell.com Syntax sntp client enable no sntp client enable Default Configuration Client is disabled on an interface. Command Mode Interface Configuration (Ethernet, port-channel, VLAN) mode User Guidelines Use the sntp broadcast client enable global configuration command to enable - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 109
mode User Guidelines Polling time is determined by the sntp client poll timer global configuration command. Examples The following example enables polling for the Simple Network Time Protocol (SNTP) predefined unicast clients: Console(config)# sntp unicast client poll sntp server The sntp server - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 110
.dell.com | support.dell.com • hostname - Hostname of the server. (Range: 1-158 characters) • poll - Enable polling. • keyid - Authentication key to use when sending packets to this peer. (Range:1-4294967295) Default Configuration No servers are defined. Command Mode Global Configuration mode User - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 111
User Guidelines The symbol that precedes the show clock display indicates the following: Symbol * following example displays the time and date from the system clock. Console> show clock 15:29:03 PDT(UTC-7) Jun 17 2005 Time source is SNTP Console> show clock detail 15:29:03 PDT(UTC-7) Jun 17 2005 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 112
| support.dell.com show sntp configuration The show sntp configuration privileged EXEC command shows the configuration of the Simple Network Time Protocol (SNTP). Syntax show sntp configuration Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 113
Protocol (SNTP). Syntax show sntp status Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. ExamSples The following example shows the status of the SNTP. Console# show sntp status Clock is - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 114
www.dell.com | support.dell.com OOB unicast servers: Server Status Last response --------176.1.1.8 -----Unknown 19:19:51.198 PDT Feb 19 2005 Offset [mSec] ----2.98 Delay [mSec] -----129.19 Anycast server: Server --------176.1.11.8 Interface Status Last response ------- ----VLAN 118 Up - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 115
enable no ip dhcp relay enable Default Configuration DHCP is disabled on the router. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example enables DHCP services on the DHCP Server. Console(config)# ip dhcp relay enable ip - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 116
relay Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays DHCP relay server addresses. Console# show ip dhcp relay DHCP relay is enabled. Servers: 172 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 117
no default configuration. Example In the following example, because no keyword is entered, a prompt is displayed. After the keyword is selected, a message confirming the command entry method is displayed. Console# configure Console (config)# copy The copy privileged EXEC command copies files from - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 118
files cannot be copied to the running-config file. The entire copying process may take several minutes and differs from protocol to protocol and from network to network. While a configuration file is being copied (downloaded or uploaded), the device ignores the user input sent to the device via CLI - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 119
Use the copy source-url running-config command to load a "configuration file" from a network server to the device "running configuration". The configuration is added to the "running configuration" as if the commands were typed in the command-line interface (CLI). The resulting configuration file is - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 120
configuration" to the "backup configuration" file. Use the copy startup-config backup-config command to backup the startup configuration to the backup configuration file. Specifying out-of-band addresses To copy from/to a server on the out-of-band port, use the out-of-band P address format: oob/ip - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 121
-config file. Syntax delete startup-config Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Examples The following example deletes the startup-config file. Console# delete startup-config - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 122
. Console# boot system image-1 show running-config The show running-config privileged EXEC command displays the contents of the currently running configuration file. Syntax show running-config Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 123
example displays the contents of the running-config file. Console# show running-config Router Configuration no spanning-tree interface ethernet g1 ip address 16.1.1.3 255.0.0.0 exit radius-server host 16.1.1.200 auth-port 1812 aaa authentication enable 12 radius aaa authentication login 123 radius - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 124
no user guidelines for this command. Examples The following example displays the contents of the startup-config file. Console# show startup-config Router Configuration Empty configuration OOB host Configuration Empty configuration Default settings Router Configuration Service tag: 12345678 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 125
Gigabit Ethernet Ports no shutdown speed 1000 duplex full negotiation flow-control off mdix auto no back-pressure interface vlan 1 interface port-channel 1 - 7 no router RIP no router OSPF enable spanning-tree spanning-tree mode STP qos basic Configuration and Image Files 125 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 126
exit show backup-config The show backup-config privileged EXEC command displays the backup configuration file contents. Syntax show backup-config Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 127
-config file. Console# show backup-config no spanning-tree interface ethernet g12 ip address 12.1.1.1 255.0.0.0 exit show bootvar The show bootvar privileged EXEC command displays the active system image file that the device loads at startup. Syntax show bootvar Default Configuration This command - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 128
www.dell.com | support.dell.com 128 Configuration and Image Files - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 129
port. Default Configuration This command has no default configuration. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example enables ports g18 for configuration. Console(config)# interface ethernet g18 Console(config - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 130
, g22-24 Console(config-if)# interface out-of-band-eth The interface out-of-band-eth global configuration command configures the Out-of-Band Ethernet port and enter interface configuration mode. interface out-of-band-eth [interface] • interface-Interface number. If unspecified defaults to 1. Default - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 131
Default Configuration The interface is enabled. Command Mode Interface Configuration (Ethernet, port-channel, Out-of-Band Ethernet) mode User Guidelines There are no user guidelines for this command. Examples The following example disables Ethernet g5. Console(config)# interface ethernet g5 Console - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 132
g5 Console(config-if)# description RD_SW#3 speed The speed interface configuration command configures the speed of a given Ethernet interface when not using auto-negotiation. To restore the default, use the no form of this command. Syntax speed {10 | 100 | 1000} no speed • 10-Configures the port to - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 133
that port. Half duplex mode can be set only for ports operating at 10 Mbps or 100 Mbps. Example The following example configures the duplex operation of Ethernet g5 to force full duplex operation. Console(config)# interface ethernet g5 Console(config-if)# duplex full Ethernet Configuration Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 134
, as per the standards, set them all inactive. Example The following example enables autonegotiation with all capabilities on g5. Console(config)# interface ethernet g5 Console(config-if)# negotiation flowcontrol The flowcontrol interface configuration command configures the Flow Control on a given - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 135
on g5. Console(config)# interface ethernet g5 Console(config-if)# flowcontrol on mdix The mdix interface configuration command enables automatic crossover on a given interface. To disable automatic crossover, use the no form of this command. Syntax mdix {on | auto} no mdix • on-Manual mdix • auto - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 136
back-pressure Default Configuration Back Pressure is disabled. Command Mode Interface Configuration (Ethernet, port-channel) mode User Guidelines Back Pressure will operate only if duplex mode is set to half. Example In the following example Back Pressure is enabled on g5. Console(config)# interface - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 137
port-channel trunk index. Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Example In the following example, the counters for interface g1 are cleared. Console> clear counters ethernet g1 set - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 138
• port-channel-number-Valid port-channel trunk index. Default Configuration This command has no default configuration. Command Mode Privilege EXEC mode User Guidelines There are no user guidelines for this command. Example The following example activates interface g9, which is disabled. Console# set - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 139
following example displays the configuration for all configured interfaces: Console# show interfaces configuration Flow Admin Back Mdix Port Type Duplex Speed Neg control State Pressure Mode ...g1 1G-Copper Full 1000 Enabled Off Up Disabled Auto g2 1G-Copper Full 1000 Enabled Off Up Disabled Auto - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 140
valid Ethernet port. • port-channel-number-A valid port-channel trunk index. • oob-interface-Out-of-Band Ethernet port number. Default Configuration This command has no default configuration. Command Mode Privilege EXEC mode User Guidelines There are no user guidelines for this command. Example The - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 141
Console# show interfaces status Port Mode g1 g2 g3 g4 g5 g6 g7 g8 ... g22 g23 g24 Type Duplex Speed Neg -- -- Not Present -- ch7 -- -- -- -- -- Not Present -- Link Oob-eth Type Duplex Speed Neg State Oob-eth 1 100M-Copper Full 100 Enabled Up Ethernet Configuration Commands 141 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 142
-Valid Ethernet port. • port-channel-number-A valid port-channel trunk index. • oob-interface-Out-of-Band Ethernet port number. Default Configuration This command has no default configuration. Command Modes Privilege EXEC mode User Guidelines There are no user guidelines for this command. 142 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 143
port-channel-number] • interface-A valid Ethernet port. • port-channel-number-A valid port-channel index. Default Configuration This command has no default configuration. Command Modes Privilege EXEC mode User Guidelines There are no user guidelines for this command. Ethernet Configuration Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 144
www.dell.com | support.dell.com Examples The following example displays traffic seen by the physical interface: Console# show interfaces counters Port InOctets OutBcastPkts ch1 0 0 0 0 ch2 0 0 0 0 ch3 0 0 0 0 ... ch7 0 0 0 0 144 Ethernet Configuration Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 145
example displays counters for port g1. Console# show interfaces counters ethernet g1 Port InOctets InUcastPkts InMcastPkts InBcastPkts g1 0 0 0 0 Port OutOctets OutUcastPkts OutMcastPkts OutBcastPkts octets in length but do not pass the FCS check. Ethernet Configuration Commands 145 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 146
command has no default configuration. Command Modes User EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays the jumbo frames configuration. Console# show ports jumbo-frame Jumbo frames are disabled Jumbo frames will be enabled after reset - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 147
rate. Example The following example enables the counting of Multicast packets. Console# configure Console(config)# port storm-control include-multicast port storm-control broadcast enable The port storm-control broadcast enable interface configuration command enables Broadcast storm control. To - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 148
command, to set the maximum allowable Broadcast rate. Multicast can be counted as part of the "storm" frames if the port storm-control includemulticast global configuration command is already executed. Example The following example enables Broadcast storm control on port g5. Console(config - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 149
-A valid Ethernet port. Default Configuration This command has no default configuration. Command Modes Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays the storm control configuration. Console# show ports storm-control - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 150
www.dell.com | support.dell.com Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays information about auto negoiation advertisement. Console# show - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 151
VLANs dynamically. The gvrp enable global configuration command enables GVRP globally. To disable GVRP globally on the switch, use the no form of this command. Syntax gvrp enable no gvrp enable Default Configuration GVRP is globally disabled. Command Mode Global Configuration mode User Guidelines - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 152
VLAN. Example The following example enables GVRP on ethernet g8. Console (config)# interface ethernet g8 Console (config-if)# gvrp enable garp timer The garp timer interface configuration command adjusts the GARP application join, leave, and leaveall GARP timer values. To reset the timer to default - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 153
The following example sets the leave timer for port g8 to 900 milliseconds. Console (config)# interface ethernet g8 Console (config-if)# garp timer leave 900 gvrp vlan-creation-forbid The gvrp vlan-creation-forbid interface configuration command enables or disables dynamic VLAN creation. To disable - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 154
www.dell.com | support.dell.com Example The following example disables dynamic VLAN creation on port g8. Console (config)# interface ethernet g8 Console (config-if)# gvrp vlan-creation-forbid gvrp registration-forbid The gvrp registration-forbid interface configuration command de-registers all - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 155
statistics information on port g8. Console# clear gvrp statistics ethernet g8 show gvrp configuration The show gvrp configuration User EXEC command displays GVRP configuration information, including timer values, whether GVRP and dynamic VLAN creation is enabled, and which ports are running GVRP - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 156
www.dell.com | support.dell.com . Console# show gvrp statistics In Received rLA : Leave All Received sJIn : Join In Sent sLIn : Leave In Sent sLA : Leave All Sent Port rJE rJIn rEmp rLIn rLE rLA sJE sJIn sEmp sLIn sLE sLA g1 0 0 0 0 0 0 0 0 0 0 0 0 g2 0 0 0 0 0 0 0 0 0 0 0 0 g3 0 0 0 0 0 0 0 0 0 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 157
Console# show gvrp configuration GVRP Feature is currently enabled on the switch. Maximum VLANs: 256, Maximum VLANs after reset: 256. Port GVRP- Regist- Dynamic Timers Crea- Join Leave Leave- Status ration VLAN (milli- tion All seconds) g1 Enabled Normal Enabled 200 600 10000 g2 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 158
www.dell.com | support.dell.com Syntax show gvrp error-statistics [ethernet interface | port-channel port-channel-number] • interface-Valid Ethernet interface. • port-channel-number-A valid port-channel trunk index. Default Configuration This command has no default configuration. Command Mode User - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 159
). Up to 5 IP addresses may be defined on the out-of-band port. Example The following example configures VLAN 1 with the IP address 131.108.1.27 and subnet mask 255.255.255.0. Console (config)# interface vlan 1 Console (config-if)# ip address 131.108.1.27 255.255.255.0 IP Addressing Commands 159 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 160
Configuration This command has no default configuration. Command Mode Interface configuration (Ethernet, VLAN, port-channel, out-of-band Ethernet) User Guidelines The ip address dhcp command allows any interface to dynamically learn its IP address by using the DHCP protocol. Some DHCP servers - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 161
set the default gateway. Example The following example defines ip default gateway 192.6.32.17. Console (config)# interface out-of-band-eth 1 Console (config-oob)# ip address 192.168.1.23 Console (config-oob)# ip default-gateway 192.168.1.1 show ip interface The show ip interface user EXEC command - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 162
-Out-of-band Ethernet port number. Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays VLAN 1 configuration. Console# show ip interface vlan 1 arp The arp - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 163
adds the IP address 198.133.219.232 and MAC address 00-00-0c-40-0f-bc to the ARP table. Console (config)# arp 198.133.219.232 0000.0c40.0fbc ethernet g8 arp timeout The arp timeout global configuration command configures how long an entry remains in the ARP cache. To restore the default value, use - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 164
www.dell.com | support.dell.com ip proxy-arp The ip proxy-arp global configuration command enables ARP proxy. To disable ARP, use the no form of this command. Syntax ip proxy-arp no ip proxy-arp Default Configuration By default ARP proxy is disabled. Command Mode Global Configuration mode User - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 165
The show arp privileged EXEC command displays entries in the ARP table. Syntax show arp Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines To enter an out-of-band IP interface, use the out-of-band IP address format - oob/ipaddress. Only - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 166
.dell.com Command Mode IP Interface Configuration mode User Guidelines There are no user guidelines for this command. Example The following example enables the translation of directed broadcasts to physical broadcasts on IP interface 1.0.0.1. Console(config)# interface ip 1.0.0.1 Console(config-ip - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 167
for the default services are forwarded to the helper address. Default Configuration Disabled Command Mode Global Configuration User Guidelines The ip helper-address command forwards specific UDP broadcast from one interface to another. You can define many helper addresses but the total number of - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 168
www.dell.com | support.dell.com Example Console(config)#ip helper address 100.10.1.1 helper-address The helper-address interface configuration command enables forwarding User Datagram Protocol (UDP) Broadcast packets received on an interface. To disable forwarding Broadcast packets to specific - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 169
global configuration commands and the show ip dhcp relay privileged EXEC command. Example The following example enables the software to forward UDP broadcasts on interface 1.100.100.0 to IP address 172.16.9.9 to ports 49 and 53. Console(config)# interface ip 1.100.100.0 Console (config-ip)# helper - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 170
There are no user guidelines for this command. Example The following example enables the IP Domain Naming System (DNS)-based host name-to-address translation: Console(config)# ip domain-lookup ip domain-name The ip domain-name global configuration command defines a default domain name used - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 171
There are no user guidelines for this command. Example The following example defines a default domain name of dell.com: Console(config)# ip domain-name dell.com ip name-server The ip name-server global configuration command defines available name servers. To delete a name server, use the no - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 172
www.dell.com | support.dell.com Syntax ip host name address no ip host name • name-Host name (Range: 1-158 characters). • address-IP address of the host. For information about specifying an out-of-band IP address, see the user guidelines. Default Configuration No host is defined. Command Mode - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 173
user EXEC command displays the default domain name, a list of name server hosts and the static and cached list of host names and addresses. Syntax show hosts [name] • name-Host name (Range: 1-158 characters). Default Configuration This command has no default configuration. IP Addressing Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 174
user guidelines for this command. Example The following example displays information about IP hosts. Console> show hosts Host name: Device Default domain: gm.com, sales.gm.COM, usa.sales.gm.com(DHCP) Name/address lookup is enabled Name servers (Preference order): 176.16.1.18 176.16.1.19 Configured - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 175
are no user guidelines for this command. Example The following example enables IGMP snooping. Console (config)# ip igmp snooping ip igmp snooping (Interface) The ip igmp snooping interface configuration command enables Internet Group Management Protocol (IGMP) snooping on a specific VLAN. To disable - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 176
.dell.com User Guidelines IGMP snooping can only be enabled on static VLANs. Example The following example enables IGMP snooping on VLAN 2. Console (config)# interface vlan 2 Console (config-if)# ip igmp snooping ip igmp snooping mrouter The ip igmp snooping mrouter interface configuration command - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 177
vlan 2 Console (config-if)# ip igmp snooping host-time-out 300 ip igmp snooping mrouter-time-out The ip igmp snooping mrouter-time-out interface configuration command configures the mrouter-time-out. The mrouter-time-out command is used for setting the aging-out time after Multicast router ports - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 178
www.dell.com | support.dell.com Example The following example configures the mrouter timeout to 200 seconds. Console (config)# interface vlan 2 Console (config-if)# ip igmp snooping mrouter-time-out 200 ip igmp snooping leave-time-out The ip igmp snooping leave-time-out command configures the leave - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 179
. Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Example The following example shows IGMP snooping mrouter information. Console # show igmp snooping mrouter VLAN Ports 2 9 show ip - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 180
by IGMP snooping. Syntax show ip igmp snooping groups [vlan vlan-id] [address ip-multicast-address] • vlan_id-VLAN ID value. • ip-multicast-address-IP Multicast address. Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines To see the full - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 181
Example The example shows IGMP snooping information on VLAN 1000. Console # show ip igmp snooping groups Vlan IP Address Querier Ports 1 224-239.130|2.2.3 Yes g1, g2 19 224-239.130|2.2.8 Yes g9-11 IGMP Snooping Commands 181 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 182
www.dell.com | support.dell.com 182 IGMP Snooping Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 183
There are no user guidelines for this command. Example The following example configures an IP interface and enters the IP interface configuration mode. Console (config)# interface ip 192.168.1.1 Console (config-ip)# ip route The ip route global configuration command establishes static IP routes. To - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 184
ICMP unreachable route is returned. Default Configuration The metric default distance is 1. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example establishes a static route to 172.16.0.0. Console (config)# ip route 172.16 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 185
Mode Key chain configuration mode User Guidelines It is useful to have multiple keys on a key chain so that the software can sequence through the keys as they become invalid after time, based on the accept-lifetime and send-lifetime key chain key command settings. Authentication keys and their - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 186
3 Console (config-key)# key-string The key-string SSH public key chain configuration command manually specifies an SSH public key. Syntax key-string key-string row key-string • row-Specifies SSH public key row by row. • key-string-UU-encoded DER format is the same format in the authorized_keys file - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 187
specifies SSH public row keys "AAAAB3Nza" and "C1yc2". Console(config)# crypto key pubkey-chain ssh Console(config-pubkey-chain)# user-key bob rsa Console(config-pubkey-key)# key-string row AAAAB3Nza Console(config-pubkey-key)# key-string row C1yc2 IP Routing Protocol-Independent Commands 187 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 188
www.dell.com | support.dell.com accept-lifetime The accept-lifetime key chain key configuration command sets the time period during which the authentication key is valid for authenticating incoming packets. To reset to the default value, use the no form of this command. Syntax accept-lifetime - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 189
key-string country Console (config-key)# accept-lifetime duration 14:30:00 Jan 25 2005 7200 send-lifetime The send-lifetime key chain key configuration command sets the time period during which an authentication key is valid to generate MD5 digest for outgoing packets. To revert to the default value - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 190
Console (config-key)# exit Console (config)# key 2 Console (config-key)# key-string country Console (config-key)# send-lifetime 15:00:00 Jan 25 2005 duration 3600 ip maximum-paths The ip maximum-paths global configuration command defines the maximum number of parallel routes. To restore the default - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 191
Configuration mode User Guidelines The change to IP maximum-paths takes effect after resetting the device. Example The following example defines the maximum number of parallel routes to 2. Console (config)# ip maximum-paths 2 show ip route The show ip route user EXEC command displays the routing - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 192
www.dell.com | support.dell.com Examples The following example displays the whole routing table state. Console> show ip route Maximum Parallel Paths: 2 (4 after reset) Codes: C - connected, S - static, R - RIP, O - OSPF, E - OSPF external R 10.0.0.0/8 is rejected C 10.0.1.1/32 is directly connected - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 193
IP address and address mask. Console> show ip route routing protocols. Syntax show ip protocols Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. IP Routing Protocol-Independent Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 194
www.dell.com | support.dell.com Example The following example displays the parameters and current state of the active routing protocol process. Console# show ip protocols Routing Protocol is "rip" Sending updates every 30 seconds Invalid after 180 seconds, hold down 120, flushed after 300 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 195
Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays key-chain information. Console :00:00 Jan 25 2005 IP Routing Protocol-Independent Commands 195 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 196
www.dell.com | support.dell.com show keys The show keys privileged EXEC command displays key information. Syntax show keys [key-id] • key-id-Identification number of an authentication key on a key chain. (Range: 1 - 255) Default Configuration This command has no default configuration. Command Mode - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 197
to 120. Console (config)# lacp system-priority 120 lacp port-priority The lacp port-priority interface configuration command configures the priority value for physical ports. To reset to default priority value, use the no form of this command. Syntax lacp port-priority value no lacp port-priority - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 198
the priority value for port g8 to 247. Console (config)# interface ethernet g8 Console (config-if)# lacp port-priority 247 lacp timeout The lacp timeout interface configuration command assigns an administrative LACP timeout. To reset the default administrative LACP timeout use the no form - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 199
. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example shows how to display LACP statistics information. Console# show lacp ethernet g1 statistics Port 1 LACP - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 200
www.dell.com | support.dell.com Example The following example shows how to display LACP port-channel information. Console# show lacp port-channel 1 Port-Channel ch1 Port Type Unknown Attached Lag id: Actor System Priority:1 MAC Address: 0a:d0:0f:f0:eb:ee Admin Key: 25 Oper Key: 25 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 201
for remote console access. Console(config)# line telnet Console(config-line)# speed The speed line configuration command sets the line baud rate. Syntax speed {bps} • bps-Baud rate in bits per second (bps). The options are 2400, 9600, 19200 and 115200. Default Configuration This default speed is - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 202
www.dell.com | support.dell.com Command Mode Line Configuration (console) mode User Guidelines This command is available only on the console line. Although not saved to the configuration file, the line baud rate setting is permanently saved until it is explicitly modified. Examples The following - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 203
access (SSH). Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Examples The following example displays the line configuration. Console# show line Console configuration: Interactive timeout - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 204
function for the current terminal session. Console# no terminal history terminal history size The terminal history size user EXEC command configures the command history buffer size for the current terminal session. To reset the command history buffer size to the default setting, use the no form of - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 205
change the default size of the command history buffer, use the history size line configuration command. The maximum number of commands in all buffers is 256. Examples The following example configures the command history buffer size to 20 commands for the current terminal session. Console # terminal - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 206
www.dell.com | support.dell.com 206 Line Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 207
name • name-The access list name using up to 32 characters. Default Configuration This command has no default configuration. Command Mode Global Configuration mode User Guidelines This command enters the access-list configuration mode, where the denied or permitted access conditions with the deny - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 208
exit Console (config)# management access-class mlist permit (management) The permit management access-list configuration command defines a permit rule. Syntax permit [ethernet interface-number | vlan vlan-id | port-channel number | out-of-band-eth oob-interface] [service service] permit ip-source ip - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 209
access-list mlist Console (config-macl)# permit deny (management) The deny management access-list configuration command defines a deny rule. Syntax deny [ethernet interface-number | vlan vlan-id | port-channel number | out-of-band-eth oobinterface] [service service] deny ip-source ip-address [mask - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 210
the console. Default Configuration This command has no default configuration. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example configures an access-list called "mlist" as the management access-list. Console (config - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 211
-A valid access list name. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays the active management access-list. Console# show management access-list - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 212
www.dell.com | support.dell.com User Guidelines There are no user guidelines for this command. Example The following example displays the management access-list information. Console# show management access-class Management access-class is enabled, using access list mlist 212 Management ACL - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 213
Console (config)# ip multicast-routing ip dvmrp The ip dvmrp interface configuration mode enables DVMRP on an interface. To disable DVMRP, use the no form of this command. Syntax ip dvmrp no ip dvmrp Default Configuration DVMRP is disabled. Command Mode Interface configuration (Ethernet, VLAN, port - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 214
to default. This command is available only when DVMRP is enabled. Example The following example configures the interface metric for DVMRP on port g5 to 15. Console (config)# interface ethernet g5 Console (config-if)# ip dvmrp metric 15 ip igmp The ip igmp interface configuration command enables IGMP - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 215
return to the default values. Example The following example enables IGMP on port g5. Console (config)# interface ethernet g5 Console (config-if)# ip igmp ip igmp query-interval The ip igmp query-interval interface configuration command configures the frequency at which the software sends Internet - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 216
The default frequency is 1 second. Command Mode Interface configuration (Ethernet, VLAN, port-channel) User Guidelines IGMP must be enabled before setting the frequency. If IGMP is disabled on an interface, the IGMP parameters on the interface return to the default values. 216 Multicast Routing - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 217
command has no default configuration. Command Mode Interface configuration (Ethernet, VLAN, port-channel) User Guidelines IGMP must be enabled before setting the response time. If IGMP is disabled on an interface, the IGMP parameters on the interface return to the default values. Multicast Routing - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 218
form of this command. Syntax ip igmp version {1 | 2} no ip igmp version • 1-IGMP version 1 • 2-IGMP version 2 Default Configuration The default is IGMP version 2. Command Mode Interface configuration (Ethernet, VLAN, port-channel) User Guidelines IGMP must be enabled before setting the IGMP version - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 219
configures the router to be a statically connected member of the specified group on port g5 with IP address 224.0.0.0. Console (config)# interface ethernet g5 Console (config-if)# ip igmp static-group 224.0.0.0 show ip mroute The show ip mroute user EXEC command displays the IP Multicast routing - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 220
dell.com | support.dell.com Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Examples The following example displays all ip mroutes. Console# show ip :55 dvmrp 220 Multicast Routing Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 221
displays all ip mroutes for port g1. Console# show ip mroute ethernet routing information was learned by the router. The minimum amount of time remaining before this entry is aged out. The Multicast routing protocol via which this Multicast forwarding entry was learned. Multicast Routing Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 222
source-address-The source IP address. Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays Multicast next hop information. Console# show ip mroute-next-hop - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 223
interface-number-Ethernet port number. • vlan vlan-id-VLAN number. • port-channel number-Port-channel number. Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Multicast Routing Commands 223 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 224
-neighbor information on a per-interface basis. Syntax show ip dvmrp neighbor [ethernet interface-number | vlan vlan-id | port-channel number] • ethernet interface-number-Ethernet port number. • vlan vlan-id-VLAN number. • port-channel number-Port-channel number. 224 Multicast Routing Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 225
Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Examples The following example displays DVMRP neighbor information for port g1. Console# show ip interfaces. Console# show ip dvmrp neighbor - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 226
interface-number-Ethernet port number. • vlan vlan-id-VLAN number. • port-channel number-Port-channel number. Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. 226 Multicast Routing Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 227
. Console# show ip dvmrp ip dvmrp route [ip-address] • ip-address-IP address of an entry in the DVMRP routing table. Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Multicast Routing Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 228
state. Syntax show ip dvmrp prune [group group-address source-address | source-address] • group-address-Multicast group IP address • source-address-The source IP address Default Configuration This command has no default configuration. Command Mode User EXEC mode 228 Multicast Routing Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 229
ip igmp interface [ethernet interface-number | vlan vlan-id | port-channel number] • ethernet interface-number-Ethernet port number. • vlan vlan-id-VLAN number. • port-channel number-Port-channel number. Default Configuration This command has no default configuration. Multicast Routing Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 230
www.dell.com | support.dell.com Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays IGMP related information about an interface. Console# show ip igmp interface Interface Version Query Last Max Querier Interval - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 231
vlan-id-VLAN number. • port-channel number-Port-channel number. Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Example The following example configures authentication login. Console# show ip - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 232
www.dell.com | support.dell.com The following table describes the fields shown in the display: Field Group Address Interface Uptime Expires Last Reporter , because the entry is defined as static. Last host to report being a member of the Multicast group. 232 Multicast Routing Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 233
command. Syntax router ospf enable no router ospf enable Default Configuration The OSPF routing process is disabled. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example enables the OSPF routing process. Console (config - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 234
area with the value of 1. . Console (config)# router ospf area 0.0.0.1 router ospf redistribute rip The router redistribute rip global configuration command enables incorporating IP routes that have been learned via the RIP routing process into the OSPF routing process. To disable the redistribution - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 235
static Default Configuration Statically configured route advertising is disabled. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example enables route advertisements statically configured while running OSPF. Console (config - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 236
of directly connected network routes is disabled. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example enables advertisements of directly connected networks routes, running OSPF. Console (config)# router ospf redistribute - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 237
address 1.1.1.1. Console (config)# router ospf area 1.1.1.1 virtual-link 1.1.1.1 hello-interval The hello-interval ospf virtual link interface configuration command specifies the interval between hello packets that the software sends on the OSPF virtual link interface. To return to the default time - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 238
- 2147483647) Default Configuration The default is 60 seconds. Command Mode OSPF virtual link configuration User Guidelines The interval is advertised in router hello packets. This value must be the same for all routers and access servers on a specific network. Example The following example sets the - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 239
Console# (config-vlink)# retransmit-interval 10 transmit-delay The transmit-delay ospf virtual link interface configuration command sets the estimated time required to send a link-state update packet on the OSPF virtual link interface. To return to the default value, use the no form of this command - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 240
. Default Configuration No authentication is provided for OSPF packets. Command Mode OSPF virtual link configuration User Guidelines There are no user guidelines for this command. Example The following example enables authentication for OSPF packets as MD5 with chain name of "hhv". Console (config - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 241
interface IP address. Command Mode Global Configuration mode User Guidelines An arbitrary value for the ip-address keyword for each router can be configured; however, each router ID must be unique. Example The following example configures an OSPF router ID as 196.127.2.1. Console (config)# router - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 242
www.dell.com | support.dell.com User Guidelines The router ospf area stub command must be configured on all routers and access servers in the stub area. Use the area router configuration command with the default-cost option to specify the default internal router cost sent into a stub area by an ABR - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 243
The following example specifies a cost of 10000 for the default summary route sent into a stub area number 192.168.3.1. Console (config)# router ospf area 192.168.3.1 default-cost 10000 ospf The ospf interface configuration command creates the OSPF routing process on an interface. To delete the OSPF - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 244
.100. Console(config)# interface ip 1.100.100.100 Console(config-ip)# ospf ospf enable The ospf enable interface configuration command activates OSPF on an interface. To deactivate OSPF on an interface, use the no form of this command. Syntax ospf enable no ospf enable Default Configuration OSPF is - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 245
on IP interface 1.100.100.100. Console(config)# interface ip 1.100.100.100 Console(config-ip)# ospf Console(config-ip)# ospf area 192.168.2.1 ospf cost The ospf cost interface configuration command specifies the cost of sending a packet on an interface. To reset the path cost to the default value - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 246
interface 1.100.100.100. Console(config)# interface ip 1.100.100.100 Console(config-ip)# ospf cost 250 ospf priority The ospf priority interface configuration command sets the router priority, which is used in electing the designated router for the network. To return to the default value, use the no - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 247
servers on a specific network. Example The following example defines the hello-time of 100 seconds on IP interface 1.100.100.100. Console(config)# interface ip 1.100.100.100 Console(config-ip)# ospf hello-interval 100 ospf dead-interval The ospf dead-interval interface configuration command sets - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 248
www.dell.com | support.dell.com Default Configuration The default IP Interface dead-interval time is 40 seconds. Command Mode IP Interface Configuration User Guidelines The interval is advertised in router hello packets. This value must be the same for all routers and access servers on a specific - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 249
adjacencies. Console(config)# interface ip 1.100.100.100 Console(config-if)# ospf re-transmit-interval 60 ospf transmit-delay The ospf transmit-delay interface configuration command sets the estimated time required to send a link-state update packet on an interface. To return to the default value - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 250
following example restores the method of calculation of summary route costs as suggested by RFC 1583: Console (config)# router ospf compatible rfc1583 ospf authentication The ospf authentication interface configuration command enables authentication for OSPF packets and specifies the authentication - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 251
default configuration. Command Mode Privileged EXEC mode User Guidelines OSPF database entries learned by the device or by a specific interface cannot be cleared using the Web user interface Example The following example clears OSPF routing redistribution on IP interface 192.168.3.1. Console# clear - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 252
has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Example The following example configures authentication login. Console# show ip ospf OSPF is enabled OSPF Router ID 192.42.110.200 Supports only single TOS(TOS0) route It - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 253
the OSPF address range. It is specified as an IP address. • router-id-Router ID associated with the virtual link neighbor. Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. OSPF Commands 253 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 254
www.dell.com | support.dell.com Example The following example displays parameters and the current state of OSPF virtual links. Console# show ip ospf virtual-links Virtual Link to router 192.168.101.2 is up Transit area 0.0.0.1 Virtual link has simple password authentication Transmit Delay is - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 255
with the OSPF address range defined in the router ospf area router configuration command used to define the particular area. • adv-router [ip-address]-Displays all the specified router link-state advertisements (LSAs). If no IP address is included, the information is about the local router itself - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 256
-originate-Displays only self-originated LSAs (from the local router). • summary-Displays information only about the summary LSAs. Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. 256 OSPF - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 257
Examples The following example displays OSPF database information. Console# show ip ospf database OSPF Router with ID 200.1.1.11 Router Link States(Area 0) Link ID Link count 11 ADV Router 200.1.1.27 200.1.1.11 Age 1323 1461 Seq# 0x8000005B 0x8000005B Checksum 0xA8EE 0x7AC OSPF Commands 257 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 258
www.dell.com | support.dell.com The following table describes detected for router. The following example displays OSPF database ASBR information. Console# show ip ospf database asbr-summary OSPF Router with id 190.20.239.66 : 28 Network Mask: 0.0.0.0 TOS: 0 Metric: 1 258 OSPF Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 259
Description OSPF Router with id Router ID number. LS age Link-state age. Options Type of service options (Type 0 only). LS Type Link-state type. Link State ID Link-state ID ( LSA. Network Mask Network mask implemented. TOS Type of service. Metric Link-state metric. OSPF Commands 259 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 260
www.dell.com | support.dell.com The following example displays external OSPF database information. Console# show ip ospf database external OSPF Router with id 190.20.239.66 Type: 2 (Larger than any link state path) TOS: 0 Metric: 1 Forward Address: 0.0.0.0 External Route Tag: 0 260 OSPF Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 261
with id Router ID number. LS age Link-state age. Options Type of service options (Type 0 only). LS Type Link-state type. Link State ID set to 0.0.0.0, data traffic is forwarded to the advertisement originator. External Route Tag External route tag, a 32-bit field attached. OSPF Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 262
www.dell.com | support.dell.com The following example displays OSPF database network information. Console# show ip ospf database network OSPF Router with id 190.20.239.66 Displaying Net Link States(Area : 155.187.1.1 Attached Router: 155.187.54.5 Attached Router: 155.187.1.5 262 OSPF Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 263
Number Checksum Length Network Mask Attached Router Description Router ID number. Link-state age. Type of service options (Type 0 only). Link-state type. Link-state ID of designated router. Advertising mask implemented. List of routers attached to the network, by IP address. OSPF Commands 263 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 264
www.dell.com | support.dell.com The following example displays OSPF database router information. Console# show ip ospf database router OSPF Router with id 190.20.239.66 Displaying Router Link States Router Interface address: 155.187.21.6 Number of TOS metrics: 0 TOS 0 Metrics: 2 264 OSPF Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 265
Description OSPF Router with id Router ID number. LS age Link-state age. Options Type of service options (Type 0 only). LS Type Link-state type. Link State ID Link-state ID. Link type. Link Data Router interface address. TOS Type of service metric (Type 0 only). OSPF Commands 265 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 266
www.dell.com | support.dell.com The following example displays OSPF database router information. Console# show ip ospf database summary OSPF Router with id 190.20.239.66 Displaying of the link-state advertisement. Network mask implemented. Type of service. Link-state metric. 266 OSPF Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 267
interface The show ip ospf interface user EXEC command displays OSPF-related interface information. Syntax show ip ospf interface [interface] • interface-An OSPF-related IP interface. Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 268
of adjacent neighbors. show ip ospf neighbor The show ip ospf neighbor user EXEC command displays OSPF-neighbor information on a perinterface basis. Syntax show ip ospf neighbor [interface] • interface-The IP interface. Default Configuration This command has no default configuration. 268 OSPF - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 269
Command Mode User EXEC mode User Guidelines For OSPF routers to become neighbors, they must be directly connected and agree on the following parameters. • IP prefix and subnet mask • Area ID • Authentication (none, text, MD5) • Options (stub, nssa) • Hello Interval (default 10 sec.) • Router Dead - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 270
www.dell.com | support.dell.com The following table describes fields shown in the display: Field Description Neighbor Neighbor router ID. Address IP address of the interface. In the area Area and are 0 and 2; 2 indicates area is not a stub; 0 indicates area is a stub.) 270 OSPF Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 271
to the same pair will not be reported. Syntax test copper-port tdr interface • interface-A valid Ethernet port. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines The port can only be tested if cable is connected to both sides. The - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 272
port. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays the last TDR (Time Domain Reflectometry) tests on all ports. Console# show copper-ports - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 273
valid Ethernet port. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines This feature works only on 1-Gbps ports. Example The following example displays the estimated copper cable length attached to all ports. Console# show copper - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 274
www.dell.com | support.dell.com Command Mode Privileged EXEC mode User Guidelines To test optical transceivers ensure a fiber link is present. 274 PHY Diagnostics Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 275
power in milliWatts Input Power - Measured RX received power in milliWatts TX Fault - Transmitter fault LOS - Loss of signal Data Ready - Indicates transceiver has archived power up and data is ready N/A - Not Available, N/S - Not Supported, W - Warning, E - Error PHY Diagnostics Commands 275 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 276
www.dell.com | support.dell.com The following example displays detailed optical transceiver diagnostics. Console# show fiber-ports transceiver detailed Power Port ---g1 g2 Temp Voltage [C] [Volt] 48 5.15 43 5.15 Current [mA] ------- 50 10 Output Input TX LOS [dBm] [dBm] Fault - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 277
, set them all to inactive. Example The following example enters the context of port-channel number 1. Console (config)# interface port-channel 1 interface range port-channel The interface range port-channel global configuration command enters the interface configuration mode to configure multiple - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 278
www.dell.com | support.dell.com Default Configuration This command has no default configuration. Command Mode Global Configuration mode User Guidelines Commands under the interface range context are executed independently on each interface in the range. If the command returns an error on one of the - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 279
, set them all to Inactive. Example The following example shows how port g5 is configured to port-channel number 1 without LACP. Console (config)# interface ethernet g5 Console (config-if)# channel-group 1 mode on show interfaces port-channel The show interfaces port-channel user EXEC command - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 280
www.dell.com | support.dell.com 280 Port Channel Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 281
Ethernet) mode User Guidelines This command enables traffic on one port to be copied to another port, or between the source port (src-interface) and a destination port (the port being configured). Only a single target port can be defined per system. The port being monitored cannot be set faster than - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 282
how traffic on port g8 (source port) is copied to port g1 (destination port). Console(config)# interface ethernet g1 Console(config-if)# port monitor g8 port monitor vlan-tagging The port monitor vlan-tagging interface configuration command transmits tagged ingress mirrored packets. To transmit - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 283
has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Example The following example shows how the port monitoring status is displayed. Console# show ports monitor Source Port Destination Port Type Status VLAN Tagging g1 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 284
www.dell.com | support.dell.com 284 Port Monitor Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 285
command. However, switching to Basic qos mode sets the trust mode to cos. Example The following example shows how QoS is enabled on the device, in basic mode. Console (config)# qos show qos The show qos user EXEC command displays the QoS status. Syntax show qos Default Configuration This command - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 286
Global Configuration mode User Guidelines When configuring the priority-queue out num-of-queues command, the weighted round robin (WRR) weight ratios are affected because there are fewer queues participating in WRR. Example The following example sets queue 7, 8 to be an EF queue. Console (config - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 287
example sets a shaper on port g5 when the average traffic rate exceeds 124000 bps or the a normal burst size exceeds 96000 bps. Console (config)# interface ethernet g5 Console (config-if) traffic-shape 124000 96000 qos wrr-queue threshold The qos wrr-queue threshold global configuration command - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 288
www.dell.com | support.dell.com • threshold-percentage-Specifies the tail-drop threshold percentage value. (Range: 1 - 100) Default Configuration This command has no default configuration. Command Mode Global Configuration mode User Guidelines The packet refers to a certain threshold by the - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 289
queue. Example The following example sets queue weights as follows: • Queue 1-6 • Queue 2-6 • Queue 3-6 • Queue 4-6 • Queue 5-6 • Queue 6-6 • Queue 7-6 • Queue 8-6 Console (config-if)# wrr-queue bandwidth 6 6 6 6 6 6 6 6 wrr-queue The wrr-queue interface configuration command defines the wrr-queue - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 290
all the policers configured for this interface, their setting, and the number of policers currently unused. Default Configuration For VLAN interface only the policers option is relevant. If no keyword is specified with the show qos interface command, the port QoS mode, default CoS value, DSCP - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 291
The following example displays output from the show qos interface ethernet g1 buffers command. Console# show qos interface ethernet g1 buffers Ethernet g1 Notify Q depth: qid-size 100 100 5 Enable N/A N/A N/A 6 Enable N/A N/A N/A 7 Enable N/A N/A N/A 8 Enable N/A N/A N/A - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 292
www.dell.com | support.dell.com The following example displays output from the show qos interface ethernet g1 queueing command. Console# show qos interface ethernet g1 queueing Ethernet g1 wrr bandwidth weights and EF priority: qid-weights Ef - Priority 1 - 125 dis- N/A 2 - 125 dis- N/A 3 - 125 dis - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 293
the show qos interface g1 shapers command. Console# show qos interface g1 shapers Ethernet g1 Port shaper: enable Committed rate: 192000 bps Committed burst: 9600 bytes qid Status 1 Enable 2 Disable 3 Enable 4 Disable 5 Disable 6 Disable 7 Enable 8 Enable Target Committed Rate [bps - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 294
www.dell.com | support.dell.com The following example displays output from the show qos interface g1 policers command. Console# show qos map dscp-queue global configuration command modifies the DSCP to CoS map. To return to the default map, use the no form of this command. Syntax qos map dscp-queue - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 295
Global Configuration mode User Guidelines Queue settings for 3, 11, 19, ... cannot be modified. Example The following example maps DSCP values 33, 40 and 41 to queue 1. Console (config)# qos map dscp-queue 33 40 41 to 1 qos map tcp-port-queue The qos map tcp-port-queue global configuration command - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 296
www.dell.com | support.dell.com Example The following example shows how the mapped TCP ports 2000 and 80 are modified to queue 2. Console (config)# qos map tcp-port-queue 2000 80 to 2 qos map udp-port-queue The qos map udp-port-queue global configuration command modifies the UDP-Port to DSCP table. - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 297
Weighted Random Early Detection (WRED) parameters. You enable the expedite queues by using the priority-queue out interface configuration command wrr-queue cos-map. Example The following example maps CoS 3 to queue 7. Console (config)# wrr-queue cos-map 7 3 show qos map The show qos map user EXEC - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 298
www.dell.com | support.dell.com • policed-dscp-Displays the DSCP to DSCP remark table. • dscp-mutation-Displays the DSCP-DSCP mutation table. Default Configuration This command has no default configuration. Command Mode User EXEC command User Guidelines There are no user guidelines for this command - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 299
example displays the TCP port-queue map. Tcp port-queue map: Port qid ----- ------ 6000 1 6001 2 6002 3 The following example displays the UDP port-queue map. Udp port-queue map: Port qid ----- ----- 8000 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 QoS Commands 299 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 300
is the default trust mode. Command Mode Global Configuration mode User Guidelines This command can be used only in QoS basic mode. Packets entering a quality of service (QoS) domain are classified at the edge of the QoS domain. When the packets are classified at the edge, the switch port within the - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 301
state, use the no qos command to apply best effort service. Example The following example configures the system in basic mode to DSCP trust state. Console (config)# qos trust dscp qos trust (Interface) The qos trust interface configuration command enables each port trust state while the system is - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 302
support.dell.com qos cos The qos cos interface configuration command configures the default port CoS value. To return to the default setting, use the no form of this command. Syntax qos cos default-cos no qos cos • default-cos-Specifies the default CoS value being assigned to the port. If the port - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 303
applies the DSCP Mutation map to system DSCP trusted ports. Console (config)# qos dscp-mutation qos map dscp-mutation The qos map dscp-mutation global configuration command modifies the DSCP values to the DSCP mutation map values. To return to the default mutation-map, use the no form of this - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 304
Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example defines the aggregate meter "policer1". When the average traffic rate exceeds 124000 bps, or the normal burst size exceeds 96000 bps, the packet is dropped. Console (config)# qos - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 305
policer name being displayed. Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays the aggregate policer called "policer1". Console# show qos aggregate - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 306
www.dell.com | support.dell.com Example The following example maps DSCP values 12 and 58 to value 56 while out of profile. Console (config)# qos map policed-dscp 12 58 to 56 class-map The class-map global configuration command creates class maps and enters the class-map configuration mode. To - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 307
-map class1 match-all Console (config-cmap)# show class-map The show class-map user EXEC command displays all the class-maps configured on the device. Syntax show class-map [class-map-name] • class-map-name-Specifies the class-map name being displayed. Default Configuration If no name is requested - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 308
the policy map name. Default Configuration The default behavior of the policy map is to set the DSCP value to 0 for IP packets, and to set the CoS value to 0 if the packet is tagged. Command Mode Global Configuration mode User Guidelines Before you configure policies for classes whose match - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 309
The service-policy interface configuration command cannot be used to attach policy maps that contain set or trust policy-map class configuration commands or that have access control list (ACL) classification to an egress interface. The only match criterion supported is match ip dscp dscp-list. For - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 310
, the acl-name specifies the name of the access IP/MAC list ACL. Default Configuration By default, no policy-map class-maps are defined. Command Mode Policy-map Configuration mode User Guidelines Use the policy-map global configuration command to identify the policy-map and to enter Policy-map - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 311
named "class1" with an access-group called "dell". The class is in a policy map called "policy1". Console (config)# policy-map policy1 Console (config-pmap)# class class1 access-group dell police The police policy-map class configuration command defines a policer for classified traffic. To remove - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 312
. Command Mode Policy-map Class Configuration mode User Guidelines An aggregate policer cannot be used across different policy maps or interfaces. Example The following example sets the aggregate meter "policer1" to a class-map. The class is in a policy map called "policy1". Console (config - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 313
using the service-policy interface configuration command. Trust values set with this command supersede trust values set on specific interfaces with the qos trust (Interface) interface configuration command. If specifying trust cos, QoS maps a packet to a queue using the received or default port CoS - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 314
value in the packet to 56. The class is in a policy map called "policy1". Console (config)# policy-map policy1 Console (config-pmap)# set dscp 56 service-policy The service-policy interface configuration command applies a policy map to the interface input. To detach the policy map from an interface - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 315
interface. Default Configuration This command has no default configuration. Command Mode Interface Configuration mode User Guidelines The service-policy interface configuration command cannot be used to attach policy maps that contain set or trust policy-map class configuration commands or that - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 316
www.dell.com | support.dell.com 316 QoS Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 317
Radius Commands radius-server host The radius-server host global configuration command specifies a RADIUS server host. To delete the specified RADIUS host, use the no form of this command. Syntax radius-server host ip-address [auth-port auth-port-number] [timeout timeout] [retransmit retransmit] [ - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 318
-20 seconds Console (config)# radius-server host 192.168.10.1 auth-port 20 timeout 20 radius-server key The radius-server key global configuration command sets the authentication and encryption key for all RADIUS communications between the router and the RADIUS daemon. To reset to the default, use - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 319
the software searches the list of RADIUS server hosts to 5 attempts. Console (config)# radius-server retransmit 5 radius-server source-ip The radius-server source-ip global configuration command specifies the source IP address used for communication with RADIUS servers. To return to the default, use - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 320
used for communication with RADIUS servers to 10.1.1.1. Console (config)# radius-server source-ip 10.1.1.1 radius-server timeout The radius-server timeout global configuration command sets the interval for which a router waits for a server host to reply. To restore the default, use the no form of - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 321
10 minutes. Console (config)# radius-server deadtime 10 show radius-servers The show radius-servers user EXEC command displays the RADIUS server settings. Syntax show radius-servers Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 322
www.dell.com | support.dell.com Examples The following example displays the RADIUS server settings. Console# show radius-servers IP address Auth Acct TimeOut Retransmit deadtime source IP Priority 172.16.1.1 1645 1646 3 3 0 172.16.8.1 1 172.16.1.2 1645 1646 1 18 0 172.16.8.1 2 Global - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 323
Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example enables RIP on the device. Console (config)# router rip enable router rip redistribute ospf The router rip redistribute ospf global configuration command advertises routes learned - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 324
Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example enables statically configured routes to advertise in the RIP process. Console(config)# router rip redistribute static rip The rip interface configuration command creates a Routing - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 325
There are no user guidelines for this command. Example The following example enables RIP on IP address 100.1.1.1. Console(config)# interface ip 100.1.1.1 Console(config-ip)# rip rip passive-interface The rip passive-interface interface configuration command disables the sending of routing updates on - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 326
www.dell.com | support.dell.com Default Configuration RIP auto-send is enabled. Command Mode IP Interface Configuration mode User Guidelines If auto-send is enabled on an interface, the router only advertises the default route on the interface, until a RIP message is received. When a RIP message is - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 327
adding it to the interface table on IP address 100.1.1.1. Console(config)# interface ip 100.1.1.1 Console(config-ip)# rip offset 5 rip default-route originate The rip default-route originate interface configuration command generates a metric for a default route into RIP. To disable this feature, use - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 328
www.dell.com | support.dell.com Syntax rip default-route originate metric no rip default-route originate • metric-Metric for a default route. (Range: 1- 15) Default Configuration By default, the feature is enabled. Command Mode IP Interface Configuration mode User Guidelines This command is - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 329
of 5 to generate a default route to RIP on IP address 100.1.1.1. Console(config)# interface ip 100.1.1.1 Console(config-ip)# rip default-route offset 5 rip authentication The rip authentication interface configuration command enables authentication for Routing Information Protocol (RIP) Version - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 330
support.dell.com Example The following example enables RIP clear text authentication with the password "dell" on the IP address 100.1.1.1. Console(config)# interface ip 100.1.1.1 Console(config-ip)# rip authetication text dell show ip rip The show ip rip privileged EXEC command displays RIP routing - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 331
Authentication key chain --------- 176.16.0.0/16 keychain1 The following example displays IP RIP statistics. Console# show ip rip statistics Interface Received Received Sent Bad Packets Bad Routes Updates ----------- 176.16.0.0/16 0 1 8 192.168.0.0/16 0 0 7 RIP Commands 331 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 332
dell.com | support.dell.com The following table describes the fields shown in the display: Field Description Interface The interface IP displays IP RIP peer information. Console# show ip rip peer Address Route Last Update Version Received Received Tag Bad Packets Bad Routes 176.16 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 333
port. • port-channel-number-Valid port-channel trunk index. Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays RMON Ethernet Statistics for port g1. Console - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 334
dell.com | support.dell.com The following table describes the significant fields shown in the display: Field Description Dropped The total total total total The total number total total Jabbers The total number of total number of collisions on this Ethernet segment. 64 Octets The total total total - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 335
total number of packets (including bad packets) received that are between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets). rmon collection history The rmon collection history interface configuration command enables a Remote Monitoring (RMON) MIB history - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 336
www.dell.com | support.dell.com Example The following example enables a Remote Monitoring (RMON) MIB history statistics group on port g8 with the index number "1" and a polling interval period of 2400 seconds. Console (config)# interface ethernet g8 Console (config-if)# rmon collection history 1 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 337
drop and collision counters. • period seconds-Specifies the requested period time to display. (Range: 1 - 4294967295) Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. RMON Commands 337 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 338
www.dell.com | support.dell.com Examples The following example displays RMON Ethernet Statistics history for "throughput" on index number 5. Console# show rmon history 5 throughput Sample Set: 5 Owner: cli Interface: 24 interval: 10 Requested samples: 50 Granted samples: 50 Maximum table - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 339
for "other" on index number 1. Console# show rmon history 1 other Sample Set: 1 Owner: CLI Interface: 1 interval: 10 Requested samples Undersize Oversize Description Date and Time the entry is recorded. The total number of octets of data (including those in bad packets) . RMON Commands 339 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 340
www.dell.com | support.dell.com Fragments Jabbers Dropped Collisions The total number of packets received best estimate of the total number of collisions on this Ethernet segment during this sampling interval. rmon alarm The rmon alarm global configuration command configures alarm conditions. To - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 341
• Falling threshold-1000000 • Rising threshold event index-10 • Falling threshold event index-20 Console (config)# rmon alarm 1000 dell 360000 1000000 1000000 10 20 show rmon alarm-table The show rmon alarm-table user EXEC command displays the alarms summary table. Syntax show rmon alarm-table RMON - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 342
www.dell.com | support.dell.com Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays the alarms summary table. Console# show rmon alarm-table Index OID - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 343
Guidelines There are no user guidelines for this command. Example The following example displays RMON 1 alarms. Console# show rmon alarm 1 at the end of the period. Alarm Alarm index. Owner The entity that configured this entry. Interval The interval in seconds over which the data is sampled - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 344
event. • owner name-Enter a name that specifies who configured this event. If unspecified, the name is an empty string. Default Configuration This command has no default configuration. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. 344 RMON - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 345
no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays the RMON event table. Console# show rmon events Index Description Type Community Owner Last time sent 1 Errors Log CLI Jan - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 346
www.dell.com | support.dell.com The following table describes the significant fields Range: 0 - 65535) Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 347
High Broadcast Jan 18 2005 23:59:48 Console# show rmon log Maximum table size: 500 (800 after reset) Event Description Time 1 Errors Jan 18 global configuration command configures the maximum RMON tables sizes. To return to the default configuration, use the no form of this command. - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 348
www.dell.com | support.dell.com Command Mode Global Configuration mode User Guidelines The configured table size is effective after the device is rebooted. Example The following example configures the maximum RMON history table sizes to 1000 entries. Console (config)# rmon table-size history 1000 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 349
. Default Configuration This command has no default configuration. Command Mode Global Configuration mode User Guidelines Do not include spaces in the text string. Example The following example displays setting up the system contact point as "Dell_Technical_Support". Console (config)# snmp-server - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 350
Configuration mode User Guidelines Do not include spaces in the text string. Example The following example sets the device location as "New_York". Console (config)# snmp-server location New_York snmp-server enable traps The snmp-server enable traps global configuration command enables the switch - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 351
user guidelines for this command. Examples The following example displays the command to enable authentication failed SNMP traps. Console (config)# snmp-server trap authentication snmp-server set The snmp-server set global configuration command sets SNMP MIB value by the CLI. Syntax snmp-server set - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 352
the rest of the fields get their default values. Console (config)# snmp-server set rndCommunityTable rndCommunityMngStationAddr 0.0.0.0 rndCommunityString public rndCommunityAccess super snmp-server view The snmp-server view global configuration command creates or updates a Simple Network Management - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 353
interface group. Console (config)# snmp-server view user-view system included Console (config)# snmp-server view user-view system.7 excluded Console (config)# snmp-server view user-view ifEntry.*.1 included snmp-server group The snmp-server group global configuration command configures a new Simple - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 354
and read access rights to a view called user-view. Console (config)# snmp-server group user-group v3 priv read userview snmp-server filter The snmp-server filter global configuration command creates or updates a Simple Network Management Protocol (SNMP) server filter entry. To remove the specified - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 355
Console(config)# snmp-server filter filter-name ifEntry.*.1 included show snmp The show snmp privileged EXEC command displays the SNMP status. Syntax show snmp Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 356
www.dell.com | support.dell.com Example The following example displays the SNMP communications status. Console # show snmp Community-String public private private-oob private Community-Access View name IP address type read only user-view All Router read write Default 172.16.1.1 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 357
snmp views The show snmp views privileged EXEC command displays the configuration of views. Syntax show snmp views [viewname] • viewname-Specifies the name of the view. (Range: 1-30) Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode SNMP Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 358
www.dell.com | support.dell.com User Guidelines There are no user guidelines for this command. Example The following example displays the configuration of views. Console # show snmp views Name OID Tree Type user-view 1.3.6.1.2.1.1 Included user-view 1.3.6.1.2.1.1.7 Excluded user-view - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 359
-group V3 priv OOB Default "" "" Console # show snmp groups user-group Name Security Views Model Level Context Read Write Notify user-group V3 priv - Default "" "" show snmp filters The show snmp filters privileged EXEC command displays the configuration of filters. Syntax show - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 360
filters. Console # show snmp filters Name ----------user-filter user-filter user-filter OID Tree 1.3.6.1.2.1.1 1.3.6.1.2.1.1.7 1.3.6.1.2.1.2.2.1.*.1 Type --------Included Excluded Included SNMPv1/v2 Commands snmp-server community The snmp-server community global configuration command sets up - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 361
port settings with a single community, by switching between the two communities. Examples The following example configures community access string public to permit administrative access to SNMP at an administrative station with IP address 192.168.1.20. Console (config)# snmp-server community - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 362
www.dell.com | support.dell.com The following example configures community access string public to permit SNMP read-write access for the Out-of-Band port only. Console (config)# snmp-server community public rw 192.175.1.10 type oob snmp-server host The snmp-server host global configuration command - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 363
IP address format oob/ip-address. Example The following example enables SNMP traps for host 10.1.1.1 with community string "management" using SNMPv2. Console (config)# snmp-server host 10.1.1.1 management 2 SNMPv3 Commands snmp-server user The snmp-server user global configuration command configures - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 364
this user will not be displayed. To see if this user has been added to the configuration, type the show snmp users privileged EXEC command. Examples The following example configures an SNMPv3 user "John" in group "user-group". Console (config)# snmp-server user John user-group 364 SNMP Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 365
-host global configuration command specifies the recipient of Simple Network Management Protocol Version 3 notifications. To remove the specified host, use the no form of this command. Syntax snmp-server v3-host {ip-address | hostname} username [traps | informs] {noauth | auth | priv} [udp-port port - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 366
Console (config)# snmp-server v3-host 192.168.0.20 john show snmp engineID The show snmp engineID privileged EXEC command displays the ID of the local Simple Network Management Protocol (SNMP) engine. Syntax show snmp engineID Default Configuration This command has no default configuration. Command - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 367
of the user. (Range: 1-30) Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays the configuration of users. Console # show snmp users Name -----John - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 368
www.dell.com | support.dell.com 368 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 369
are no user guidelines for this command. Example The following example enables spanning-tree functionality. Console(config)# spanning-tree spanning-tree mode The spanning-tree mode global configuration command configures the spanning-tree protocol. To return to the default configuration, use the - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 370
to 25 seconds. Console(config)# spanning-tree forward-time 25 spanning-tree hello-time The spanning-tree hello-time global configuration command configures the spanning-tree bridge hello time, which is how often the switch broadcasts hello messages to other switches.To reset the default hello time - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 371
bridge hello time to 5 seconds. Console(config)# spanning-tree hello-time 5 spanning-tree max-age The spanning-tree max-age global configuration command configures the spanning-tree bridge maximum age. To reset the default maximum age, use the no form of this command. Syntax spanning-tree max-age - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 372
. Console(config)# spanning-tree priority 12288 spanning-tree disable The spanning-tree disable interface configuration command disables spanning-tree on a specific port. To enable spanning-tree on a port use, the no form of this command. Syntax spanning-tree disable no spanning-tree disable Default - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 373
the spanning-tree cost on g5 to 35000. Console(config)# interface ethernet g5 Console(config-if)# spanning-tree cost 35000 spanning-tree port-priority The spanning-tree port-priority interface configuration command configures port priority. To reset the default port priority, use the no form of this - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 374
the spanning priority on g5 to 96. Console(config)# interface ethernet g5 Console(config-if)# spanning-tree port-priority 96 spanning-tree portfast The spanning-tree portfast interface configuration command enables PortFast mode. In PortFast mode, the interface is immediately put into the forwarding - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 375
Example The following example enables PortFast on g5. Console(config)# interface ethernet g5 Console(config-if)# spanning-tree portfast spanning-tree link-type The spanning-tree link-type interface configuration command overrides the default link-type setting. To reset the default, use the no form - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 376
Configuration The default definition is flooding. Command Modes Global Configuration mode User Guidelines Use this command when STP is disabled on the PowerConnect 6024/6024F. Example The following example defines BPDU packet flooding when spanning-tree is disabled on an interface. Console(config - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 377
ports only. • mst-configuration-Displays the MST configuration. • interface-number-A valid Ethernet port number. • port-channel-number-A valid port-channel index. • instance -id-ID of the spanning -tree instance (Range: 0-15). Default Configuration This command has no default configuration. Command - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 378
www.dell.com | support.dell.com Examples The following examples display spanning-tree information. Console# show spanning-tree Spanning tree enabled mode RSTP Default port cost method: long Root ID Priority Address Path Cost Root Port Hello Time 2 sec 32768 00:01:42:97:e0:00 20000 1 (g1) - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 379
Console# show spanning-tree Spanning tree enabled mode RSTP Default port cost method: long Root ID Priority 36864 Address 00:02:4b:29:7a:00 This switch is the root. Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Interfaces Name State Prio.Nbr Cost Sts ---- --- g1 Enabled - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 380
128.2 20000 - g3 Disabled 128.3 20000 - g4 Enabled 128.4 20000 - g5 Enabled 128.5 20000 - Role ---- PortFast Type - - - - - - - - - - Console# show spanning-tree active Spanning tree enabled mode RSTP Default port cost method: long Root ID Priority Address Path Cost - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 381
Shared (STP) Console# show spanning-tree blocked ports Spanning tree enabled mode RSTP Default port cost method: long Root ID Priority Address Path Cost Root Port Hello Time 2 --- g4 Enabled 128.4 20000 BLK Role ---ALTN PortFast Type No Shared (STP) Spanning-Tree Commands 381 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 382
www.dell.com | support.dell.com Console# show spanning-tree detail Spanning tree enabled mode RSTP Default port cost method: long Root ID Priority Address Path Cost Root Port Hello Time 2 sec 32768 00:01:42:97:e0:00 20000 1 (g1) Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 36864 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 383
Port Fast: No (configured:no) Designated bridge Priority: 28672 Address: 00:30:94:41:62:c8 Designated port id: 128.25 Designated path cost: 20000 Number of transitions to forwarding state: 1 BPDU: sent 2, received 120638 Port 5 (g5) enabled State: Disabled Role: N/A Spanning-Tree Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 384
25 Designated path cost: 0 Number of transitions to forwarding state: 1 BPDU: sent 2, received 120638 Console# show spanning-tree mst-configuration Name: Region1 Revision: 1 Instance -------0 1 Vlans mapped -----------1-9, 21-4094 10-20 State ------Enabled Enabled 384 Spanning-Tree Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 385
Console# show spanning-tree Spanning tree enabled mode MSTP Default port cost method: long ###### MST 0 Vlans Mapped: 1-9, 21-4094 CST Root ID Priority 32768 Address 00:01:42:97:e0:00 Path Cost 20000 Root Port 1 (g1) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec IST Master ID - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 386
Altn Desg PortFast Type No P2p Bound (RSTP) No Shared Bound (STP) No P2p No P2p Console# show spanning-tree detail Spanning tree enabled mode MSTP Default port cost method: long ###### MST 0 Vlans Mapped: 1-9, 21-4094 CST Root ID Priority 32768 Address 00:01:42:97:e0:00 Path - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 387
topology change 35, notification 2 hello 2, max age 20, forward delay 15 Port 1 (g1) enabled State: Forwarding Port id: 128.1 Type: P2p (configured: auto) Boundary RSTP Designated bridge Priority: 32768 Designated port id: 128.25 Number of transitions to forwarding state: 1 BPDU: sent 2, received - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 388
.dell.com | support.dell.com Port 3 (g3) enabled State: Forwarding Port id: 128.3 Type: Shared (configured: auto) Internal Designated bridge Priority: 32768 Designated port id: 128.3 Number of transitions to forwarding state: 1 BPDU: sent 2, received 170638 Role: Designated Port cost: 20000 Port - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 389
:no) Address: 00:02:4b:29:7a:00 Designated path cost: 20000 Port 2 (g2) enabled State: Forwarding Port id: 128.2 Type: Shared (configured: auto) Boundary STP Designated bridge Priority: 32768 Designated port id: 128.2 Number of transitions to forwarding state: 1 BPDU: sent 2, received 170638 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 390
: 1 BPDU: sent 2, received 170638 Role: Designated Port cost: 20000 Port Fast: No (configured:no) Address: 00:02:4b:29:7a:00 Designated path cost: 20000 Console# show spanning-tree Spanning tree enabled mode MSTP Default port cost method: long ###### MST 0 Vlans Mapped: 1-9, 21-4094 CST Root ID - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 391
42:97:e0:00 This switch is root for CST and IST master. Root Port 1 (g1) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Max hops 20 spanning-tree pathcost method The spanning-tree pathcost method global configuration command sets the method by which path cost defaults are determined.. To - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 392
www.dell.com | support.dell.com If the pathcost method is long, the default configuration is: • Ethernet (10 Mbps) - 2,000,000 • Fast Ethernet (100 Mbps) - 200,000 • Gigabit Ethernet (1000 Mbps) - 20,000 • Port-Channel - 20,000 Command Mode Global Configuration mode User Guidelines This command - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 393
to 4096. Console (config) # spanning-tree mst 1 priority 4096 spanning-tree mst max-hops The spanning-tree mst priority global configuration command configures the number of hops in an MST region before the BDPU is discarded and the port information is aged out. To return to the default setting, use - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 394
16) Default Configuration The default port-priority for IEEE MSTP is 128. Command Modes Interface Configuration (Ethernet, port-channel) mode User Guidelines There are no user guidelines for this command. Example The following example configures the port priority of port g1 to 142. Console (config - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 395
g9 console (config-if) # spanning-tree mst 1 cost 4 spanning-tree mst configuration The spanning-tree mst configuration global configuration command enables configuring an MST region by entering the multiple spanning-tree (MST) mode. Syntax spanning-tree mst configuration Default Configuration This - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 396
name. Example The following example maps VLANs 10-20 to MST instance 1. Console (config)# spanning-tree mst configuration Console (config-mst)# instance 1 add vlan 10-20 name (mst) The name MST configuration command defines the configuration name. To return to the default setting, use the no form of - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 397
: 1-32). Default Configuration Device address. Command Mode MST Configuration mode User Guidelines There are no user guidelines for this command. Example The following example configures sets the configuration name to region1. Console (config) # spanning-tree mst configuration Console (config-mst - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 398
sets the configuration revision to 1. Console (config) # spanning-tree mst configuration Console (config-mst) # revision 1 show (mst) The show MST configuration command displays the current or pending MST region configuration. Syntax show {current | pending} Default Configuration This command - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 399
mst configuration Console (config-mst) # exit abort (mst) The abort MST configuration command exits the MST configuration mode without applying the configuration changes. Syntax abort Default Configuration This command has no default configuration. Command Mode MST Configuration mode User Guidelines - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 400
www.dell.com | support.dell.com Example The following example shows how to exit the MST configuration mode without saving changes. Console (config) # spanning-tree mst configuration Console (config-mst) # abort 400 Spanning-Tree Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 401
Console (config)# ip ssh port 8080 ip ssh server The ip ssh server global configuration command enables the device to be configured from a SSH server. To disable this function, use the no form of this command. Syntax ip ssh server no ip ssh server Default Configuration This default is SSH is enabled - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 402
dsa The ip ssh server global configuration command generates DSA key pairs. Syntax crypto key generate dsa Default Configuration DSA key pairs do not exist. Command Mode Global Configuration mode User Guidelines When upgrading from previous version (00.01.64) of PowerConnect 6024/6024F to the - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 403
key pairs. Console (config)# crypto key generate rsa ip ssh pubkey-auth The ip ssh pubkey-auth global configuration command enables public key authentication for incoming SSH sessions. To disable this function, use the no form of this command. Syntax ip ssh pubkey-auth no ip ssh pubkey-auth Default - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 404
The following example enables public key authentication for incoming SSH sessions. Console (config)# ip ssh pubkey-auth crypto key pubkey-chain ssh The crypto key pubkey-chain ssh global configuration command enters SSH Public Key-chain configuration mode. The mode is used to manually specify other - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 405
this command with the key-string command to specify the key. Example The following example enables a SSH public key to be manually configured for the SSH public key chain called "bob". Console(config)# crypto key pubkey-chain ssh Console(config-pubkey-chain)# user-key bob rsa Console(config-pubkey - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 406
:eb:44:13:b9:33:e9 show ip ssh The show ip ssh privileged EXEC command displays the SSH server configuration. Syntax show ip ssh Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. 406 SSH - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 407
Example The following example displays the SSH server configuration. Console# show ip ssh SSH server enabled. Port: 22 RSA key was generated. DSA (DSS) key was generated. SSH Public Key Authentication is enabled. Active incoming sessions: IP address SSH username Version Cipher Auth Code 172. - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 408
www.dell.com | support.dell.com User Guidelines There are no user guidelines for this command. Example The following example displays the SSH public keys on the device. Console# show crypto key mypubkey rsa RSA key data: 005C300D 06092A86 4886F70D 01010105 00034B00 30480241 00C5E23B 55D6AB22 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 409
displays all SSH public keys stored on the device. Console# show crypto key pubkey-chain ssh Username Fingerprint CC:F8:89:87:C8 The following example displays the SSH public called "bob". Console# show crypto key pubkey-chain ssh username bob Username: bob Key: 005C300D 06092A86 4886F70D - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 410
www.dell.com | support.dell.com 410 SSH Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 411
logging is enabled. Console (config)# logging on logging The logging global configuration command logs messages to a syslog server. To delete the syslog server with the specified address from the list of syslogs, use the no form of this command. Syntax logging ip-address [port port] [severity level - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 412
a "critical" severity level so that they are logged to a syslog server with an IP address 10.1.1.1. Console (config)# logging 10.1.1.1 severity critical logging console The logging console global configuration command limits messages logged to the console based on severity. To disable logging to the - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 413
Guidelines There are no user guidelines for this command. Example The following example limits messages logged to the console based on severity level "errors". Console (config)# logging console errors logging buffered The logging buffered global configuration command limits syslog messages displayed - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 414
to 300. Console (config)# logging buffered size 300 clear logging The clear logging privileged EXEC command clears messages from the internal logging buffer. Syntax clear logging Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 415
"alerts". Console (config)# logging file alerts clear logging file The clear logging file privileged EXEC command clears messages from the logging file. Syntax clear logging file Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 416
. Default Configuration Logging AAA login events is enabled. Command Mode Global Configuration mode User Guidelines Other types of AAA events are not subject to this command. Example The following example enables logging messages related to AAA login events. Console(config)# aaa logging login file - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 417
Default Configuration Logging file system events is enabled. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example enables logging messages related to file copy operations. Console(config)# file-system logging copy - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 418
command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays the state of logging and the syslog messages stored in the internal buffer. Console # show logging Logging is enabled. Console - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 419
Event ----------- ----- AAA Login File system Copy Management ACL Deny Status -----Enabled Enabled Enabled Buffer log: 11-Aug-2005 state to up 11-Aug-2005 15:41:43: %SYS-5-CONFIG_I: Configured from memory by console 11-Aug-2005 15:41:39: %LINEPROTO-5-UPDOWN: Line protocol on Commands 419 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 420
.com | support.dell.com show logging file The show logging file privileged EXEC command displays the state of logging and the syslog messages stored in the logging file. Syntax show logging file Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 421
Event ----------- ----- AAA Login File system Copy Management ACL Deny Status -----Enabled Enabled Enabled File log: 11-Aug-2005 15 state to up 11-Aug-2005 15:41:43: %SYS-5-CONFIG_I: Configured from memory by console 11-Aug-2005 15:41:39: %LINEPROTO-5-UPDOWN: Line protocol on Commands 421 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 422
www.dell.com | support.dell.com show syslog-servers The show syslog-servers privileged EXEC command displays the syslog servers settings. Syntax show syslog-servers Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 423
to wait for each reply, from 1 to 65,535 milliseconds. Default Configuration The default packet size is 56 bytes. The default packet count is 4 packets. The default time-out is 1,000 milliseconds. Command Mode User EXEC mode User Guidelines Press Ctrl-C to stop pinging. Following are sample results - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 424
www.dell.com | support.dell.com Examples The following example displays a ping to IP address 10.1.1.1. Console# ping 10.1.1.1 64 bytes reload privileged EXEC command reloads the operating system. Syntax reload Default Configuration This command has no default configuration. 424 System Management - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 425
year (1998 - 2097). Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example sets the system time to 13:32:00 on the 7th March 2005 . Console# clock set 13:32:00 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 426
(Range: 1-159 characters) Default Configuration This command has no default configuration. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example specifies the device host name. Console (config)# hostname Dell asset-tag The - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 427
This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays information about the active users. Console# show users Username Protocol Bob Serial John SSH Robert HTTP Location - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 428
the system clock. Console# show clock 15:29:03 Jun 17 2005 show system The show system user EXEC command displays system information. Syntax show system Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 429
: Ethernet Switch System Up Time (days,hour:min:sec): 0,00:00:17 System Contact: System Name: System Location: System MAC Address: 00:00:b0:00:00:00 Sys Object ID: 1.3.6.1.4.1.674.10895.3006 Type: PowerConnect 3424 FAN Status Fan 1 OK Fan 2 OK Power supply Source Status - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 430
www.dell.com | support.dell.com show version The show version user EXEC command displays the system version information. Syntax show version Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 431
Example The following example displays the system service tag information. Console> show system id Service Tag: 89788978 Serial number: 8936589782 Asset tag: 7843678957 traceroute The traceroute user EXEC command discovers the IP routes that packets actually take when traveling to their destinations - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 432
www.dell.com | support.dell.com Command Mode User EXEC mode User Guidelines The traceroute command takes advantage of the error messages generated by a router when a datagram exceeds its time-to-live (TTL) value. The traceroute user EXEC command starts by sending probe datagrams with a TTL value of - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 433
will actually take when traveling to their destination. Console> traceroute umaxp1.physics.lsa.umich.edu Type Esc to abort. Tracing the route to umaxp1.physics.lsa.umich.edu (141.211 host. Host name of this router. IP address of this router. Round-trip time for each of the probes that are - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 434
guidelines. Default Configuration port - Telnet port (decimal 23) on the host. Command Mode User EXEC mode User Guidelines Telnet software supports special Telnet commands in the form of Telnet sequences that map generic terminal control functions to operating system-specific functions. To issue - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 435
. Console> ^^? [Special telnet escape help] ^^ B sends telnet BREAK ^^ C sends telnet IP ^^ H sends telnet EC ^^ O sends telnet AO ^^ T sends telnet AYT ^^ U sends telnet EL ^^ x suspends the session (return to system command prompt) Several concurrent Telnet sessions can be opened and switched. To - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 436
Character generator Remote commands Daytime Discard Domain Name Service Echo Exec Finger File Transfer Protocol FTP data connections Gopher NIC hostname server Ident Protocol Internet Relay Chat Kerberos login Kerberos shell Login Printer service Network News Transport Protocol Port Number 179 19 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 437
to 176.213.10.50. Console> telnet 176.213.10.50 Esc U sends telnet EL resume The resume user EXEC command is used to switch to another open Telnet session. Syntax resume [connection] • connection - The connection number. (Range: 1 - 4) Default Configuration The default is the most recent Telnet - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 438
www.dell.com | support.dell.com Examples The following command switches to another open Telnet session number 1. console> resume 1 438 System Management - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 439
on specifying an out-of-band IP address. • priority-Determines the order in which the servers are used, where 0 is the highest priority. (Range: 0-65535) Default Configuration No TACACS+ host is specified. Command Mode Global Configuration mode User Guidelines To specify multiple hosts, multiple - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 440
). Default Configuration The default is an empty string. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example sets the authentication encryption key: Console(config)# tacacs-server key dell-s tacacs-server source-ip The - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 441
The following example specifies the source IP address: Console(config)# tacacs-server source-ip 172.16.8.1 tacacs-server timeout The tacacs-server timeout global configuration command sets the interval during which a router waits for a server host to reply. To restore the default, use the no form of - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 442
ip-address-The IP address of the TACACS+ server. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Examples The following example displays TACACS+ server settings. Console# show tacacs IP - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 443
Global values TimeOut: 3 Source IP: 172.16.8.1 OOB Source IP: 172.16.8.1 TACACS+ Commands 443 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 444
www.dell.com | support.dell.com 444 TACACS+ Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 445
system. (Range: 1 - 15) Default Configuration The default privilege level is 15. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Example The following example shows how to enter privileged mode: Console> enable enter password: Console# disable The disable - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 446
www.dell.com | support.dell.com User Guidelines There are no user guidelines for this command. Example The following example shows how to return to normal mode. Console# disable Console> login The login user EXEC command changes a login username. Syntax login Default Configuration This command has - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 447
Configuration mode to User EXEC mode. Console(config-if)# exit Console(config)# exit Console# exit(EXEC) The exit user EXEC command closes an active terminal session by logging off the device. Syntax exit Default Configuration This command has no default configuration. Command Mode User EXEC command - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 448
to the previous command mode. Console (config)# end Console # help The help command displays a brief description of the help system. Syntax help Default Configuration This command has no default configuration. Command Mode All Command modes User Guidelines There are no user guidelines for this - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 449
example enables the command history function for telnet. Console (config)# line telnet Console (config-line)# history history size The history size line configuration command configures the command history buffer size for a particular line. To reset the command history buffer size to the default - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 450
mode Default Configuration This command has no default configuration. Command Mode Privilege EXEC command mode User Guidelines There are no user guidelines for this command. Example The following example enables the debug command interface. Console(config)# Console# debug >debug Enter DEBUG Password - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 451
mode. Console# show history Console# show version Console# show clock show privilege The show privilege user EXEC command displays the current privilege level. Syntax show privilege Default Configuration This command has no default configuration. Command Mode User EXEC command mode User Guidelines - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 452
www.dell.com | support.dell.com 452 User Interface - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 453
Default Configuration This command has no default configuration. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example enters the VLAN database mode. Console (config)# vlan database Console (config-vlan)# vlan Use the vlan - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 454
VLANs). Default Configuration This command has no default configuration. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example configures the VLAN 1 IP address of 131.108.1.27 and subnet mask 255.255.255.0. Console (config - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 455
vlan 221-228,889 Console (config-if)# name The name interface configuration command adds a name to a VLAN. To remove the VLAN name use the no form of this command. Syntax name string no name • string-Unique name, up to 32 characters in length, to be associated with this VLAN. Default Configuration - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 456
number 19 with the name "Marketing". Console (config)# interface vlan 19 Console (config-if)# name Marketing switchport mode The switchport mode interface configuration command configures the VLAN membership mode of a port. To reset the mode to the appropriate default for the device, use the no form - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 457
g8. Console (config)# interface ethernet g8 Console (config-if)# switchport access vlan 23 switchport trunk allowed vlan The switchport trunk allowed vlan interface configuration command adds or removes VLANs from a trunk port. Syntax switchport trunk allowed vlan {add vlan-list | remove vlan-list - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 458
g8 Console (config-if)# switchport trunk allowed vlan add 2,5-8 switchport trunk native vlan The switchport trunk native vlan interface configuration command defines the port as a member of the specified VLAN, and the VLAN ID as the "port default VLAN ID (PVID)". To configure the default VLAN ID - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 459
. Default Configuration This command has no default configuration. Command Mode Interface Configuration (Ethernet, port-channel) mode User Guidelines There are no user guidelines for this command. Example The following example shows how to add VLANs 2, 5, and 6 to the allowed list. Console (config - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 460
disable Default Configuration Ingress filtering is enabled. Command Mode Interface Configuration (Ethernet, port-channel) mode User Guidelines There are no user guidelines for this command. Example The following example shows how to enables port ingress filtering on g8. Console (config)# interface - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 461
discard untagged frames at ingress. Console (config)# interface ethernet g8 Console (config-if)# switchport general acceptable-frame-type tagged-only switchport forbidden vlan The switchport forbidden vlan interface configuration command forbids adding specific VLANs to a port. This may be used to - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 462
www.dell.com | support.dell.com Example The following example forbids adding VLANs number 234 till 256, to g8. Console (config)# interface ethernet g8 Console (config-if)# switchport forbidden vlan add 234-256 switchport protected The switchport protected interface configuration command overrides - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 463
Default Configuration This command has no default configuration. Command Mode VLAN Database mode User Guidelines The following protocol names are reserved: • ip-arp • ipx Example The following example maps protocol ip-arp to the group named "213". Console (config)# vlan database Console (config-vlan - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 464
has no default configuration. Command Mode Interface Configuration (Ethernet, port-channel) mode User Guidelines There are no user guidelines for this command. Example The following example sets a protocol-based classification rule of protocol group 1 to VLAN 8. Console (config)# interface ethernet - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 465
privileged EXEC command displays a list of VLANs being used internally by the switch. Syntax show vlan internal usage Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. VLAN Commands 465 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 466
Syntax show vlan protocols-groups Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays protocols-groups information. Console# show vlan protocols - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 467
-Valid port-channel trunk index. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays switchport configuration individually for g1. Console# show - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 468
www.dell.com | support.dell.com Forbidden VLANS: Vlan Name 4 vlan4 Classification rules: Group ID Vlan ID 468 VLAN Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 469
Interface configuration (Ethernet, VLAN, port-channel) User Guidelines This command cannot be used with a range of ports. Example The following example defines VRRP with the IP address 172.16.1.1 and 172.16.2.1 for port g8. Console(config)# interface ethernet g8 Console(config-if)# vrrp 19 ip 172 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 470
www.dell.com | support.dell.com Default Configuration VRRP is disabled Command Mode Interface configuration (Ethernet, VLAN, port-channel) User Guidelines This command cannot be used with a range of ports. Example The following example enables VRRP number 45 on port g8. Console(config)# interface - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 471
(Ethernet, VLAN, port-channel) User Guidelines This command cannot be used with a range of ports. The owner priority cannot be modified, it is always 255. Example The following example configures VRRP number 45 priority to 150 on g8. Console(config)# interface ethernet g8 Console(config-if)# vrrp - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 472
range of ports. Example The following example defines the source IP address 168.192.1.1 for VRRP messages on g8. Console(config)# interface ethernet g8 Console(config-if)# vrrp 45 source-ip 168.192.1.1 vrrp authentication The vrrp authentication interface configuration command enables authentication - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 473
Mode Interface configuration (Ethernet, VLAN, port-channel) User Guidelines This command cannot be used with a range of ports. Example The following example enables authentication for the VRRP number 45 with the password "Dell" on g8. Console(config)# interface ethernet g8 Console(config-if)# vrrp - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 474
.dell.com Syntax show vrrp configuration [ethernet interface-number | vlan vlan-id | port-channel number] • ethernet interface-number-Ethernet port number. • vlan vlan-id-VLAN number. • port-channel number-Port-channel number. Default Configuration There are no user guidelines for this command - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 475
id-VLAN number. • port-channel number-Port-channel number. Default Configuration There are no user guidelines for this command. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example configures authentication login. Console - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 476
www.dell.com | support.dell.com 476 VRRP Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 477
the http port number is configured to 100. Console (config)# ip http port 100 ip http server The ip http server global configuration command enables the device to be configured from a browser. To disable this function use the no form of this command. Syntax ip http server no ip http server Default - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 478
enables the device to be configured from a browser. Console (config)# ip http server ip https port The ip https port global configuration command configures a TCP port for use by a secure web browser to configure the device. To use the default port, use the no form of this command. Syntax ip https - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 479
Command Mode Global Configuration mode User Guidelines You must use the crypto certificate generate command to generate the HTTPS certificate. Example The following example enables the device to be configured from a browser. Console (config)# ip https server crypto certificate generate The crypto - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 480
www.dell.com | support.dell.com common- name-The default value is the lowest IP address of the device when the certificate is generated. days-The default value is 365 days. Command Mode Global Configuration mode User Guidelines The command is not saved in the router configuration; however, the - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 481
User Guidelines Use this command to export a certificate request to a configuration command to import the certificate into the device. This certificate replaces the self-signed certificate. Examples The following example generates and displays a certificate request for HTTPS. Console Web Server - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 482
support.dell.com crypto certificate import The crypto certificate import global configuration command imports a certificate signed by the Certification Authority for HTTPS. Syntax crypto certificate number import • number-Specifies the certificate number. (Range: 2 characters) Default Configuration - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 483
default setting, use the no form of this command . Syntax ip https certificate number no ip https certificate • number-Specifies the certificate number. (Range: 2 characters) Default Configuration The default value of the certificate number is 1. Command Mode Global Configuration mode Web Server - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 484
server configuration. Console# show ip http HTTP server enabled. Port: 80 show ip https The show ip http privileged EXEC command displays the HTTPS server configuration. Syntax show ip https Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode 484 Web - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 485
There are no user guidelines for this command. Example The following example displays the HTTP server configuration. Console# show ip https HTTPS server enabled. Port: 443 Certificate 1 is active Issued com, 0= General Motors, C= US Finger print: 1873B936 88DC3411 BC8932EF 782134BA Web Server 485 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 486
www.dell.com | support.dell.com 486 Web Server - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 487
. Examples The following example uses the aaa authentication dot1x default command with no authentication: Console(config)# aaa authentication dot1x default none dot1x system-auth-control The dot1x system-auth-control global configuration command enables 802.1x globally. To disable 802.1x globally - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 488
for this command. Examples The following example enables 802.1x globally: Console(config)# dot1x system-auth-control dot1x port-control The dot1x port-control interface configuration command enables manual control of the authorization state of the port. To return to the default setting, use the - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 489
authentication on the interface: Console(config)# interface ethernet g16 Console(config-if)# dot1x port-control auto dot1x re-authentication The dot1x re-authentication interface configuration command enables periodic re-authentication of the client. To return to the default setting, use the no form - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 490
) Default Configuration Re-authentication period is 3600 seconds. Command Mode Interface Configuration (Ethernet) mode User Guidelines There are no user guidelines for this command. Examples The following example sets the number of seconds between re-authentication attempts, to 300: Console(config - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 491
unusual circumstances, such as unreliable links or specific behavioral problems with certain clients authentication servers. To provide a faster response time to the user, a smaller number than the default should be entered. Examples The following example sets the number of seconds that the device - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 492
links or specific behavioral problems with certain clients and authentication servers. Examples The following command sets the number of seconds that the device waits for a response to an EAPrequest/identity frame to 3600 seconds. Console(config)# interface ethernet g16 Console(config-if)# dot1x - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 493
time is set to 30 seconds. Command Mode Interface Configuration (Ethernet) mode User Guidelines The default value of this command should be changed only to adjust for unusual circumstances, such as unreliable links or specific behavioral problems with certain clients and authentication servers. 802 - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 494
of time is set to 30 seconds. Command Mode Interface Configuration (Ethernet) mode User Guidelines There are no user guidelines for this command. Examples The following example sets the time for the retransmission of packets to the authentication server., to 3600 seconds: Console(config-if)# dot1x - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 495
Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Examples The following example displays 802.1x port g11 status. Console# show dot1x 802.1x is enabled Port g1 g2 g3 g4 g5 Admin Mode - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 496
www.dell.com | support.dell.com Tx period: 30 Seconds Max req: 2 Supplicant timeout: 30 Seconds Server timeout: 30 Seconds Session Time (HH:MM:SS): 08:19:17 MAC Address: 00:08:78:32:98:78 Authentication Method: Remote Termination Cause: Supplicant - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 497
Server. show dot1x users The show dot1x users privileged EXEC command displays 802.1x users for the device. Syntax show dot1x users [username username] • username - Supplicant username (Range: 1- 160 characters) Default Configuration This command has no default configuration. Command - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 498
statistics privileged EXEC command displays 802.1x statistics for the specified interface. Syntax show dot1x statistics ethernet interface • interface - Ethernet port name. The full syntax is unit/port. Default Configuration This command has no default configuration. Command Mode Privileged EXEC - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 499
are no user guidelines for this command. Examples The following example displays 802.1x statistics for the specified interface. Console# show dot1x statistics ethernet g1 EapolFramesRx: 11 EapolFramesTx: 12 EapolStartFramesRx: 1 EapolLogoffFramesRx: 1 EapolRespIdFramesRx: 3 EapolRespFramesRx - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 500
VLAN configuration command enables unauthorized devices access to that VLAN. To disable access, use the no form of this command. Syntax dot1x auth-not-req no dot1x auth-not-req Default Configuration User should be authorized to access the VLAN. Command Mode VLAN Configuration mode User Guidelines - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 501
unauthenticated VLANs, multiple hosts are always enabled. Examples The following command allows multiple hosts (clients) on an 802.1x-authorized port: Console(config-if)# dot1x multiple-hosts dot1x single-host-violation The dot1x single-host-violation interface configuration command configures the - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 502
www.dell.com | support.dell.com • discard-shutdown - Discard frames with source addresses that are not the supplicant address, and shut down the port. • trap - Send SNMP traps • seconds - Minimum time in seconds between consecutive traps. (Range: 1- 1000000) Default Configuration Discard frames - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 503
VLANs: 91,92 Port ---g1 g2 Multiple Hosts Disabled Enabled Console# show dot1x advanced ethernet g1 Port ---g1 Multiple Hosts Disabled Single host parameters Violation action: Discard Trap: Enabled Trap frequency: 100 Status: Single-host locked Violations since last trap: 9 802.1x Commands - Dell PowerConnect 6024 | Command
Line Interface (CLI) Guide (.htm) - Page 504
www.dell.com | support.dell.com 504 802.1x Commands
www.dell.com | support.dell.com
Dellâ„¢ PowerConnectâ„¢ 6024/6024F Systems
CLI Reference Guide