HP rp3440 User Service Guide, Sixth Edition - HP 9000 rp3410/rp3440 - Page 39

Powering On the Server, Powering On the Server Using the iLO MP

Get HP rp3440 PDF manuals and user guides View all HP rp3440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Table 1-17 Power States Power States Standby power Full power Off Power Cable Plugged Into Receptacle? Yes Yes No Power Activated through the iLO MP PC Command; or Front Panel Power Button Activated? Standby DC Voltage Applied? No Yes Yes Yes No No DC Voltage Applied? No Yes No NOTE: If the power restore feature is set to Always On through the iLO MP PR command, the server automatically powers on to the full power state. Powering On the Server To power on the server to full power if the server is in the standby power state, use the following methods: • iLO MP PC command • Power button Powering On the Server Using the iLO MP NOTE: If the power restore feature is set to Always On through the iLO MP PR command, the server automatically powers on to the full power state. To power on the server using the iLO MP, follow these steps: 1. Plug all the power cables into the receptacles on the rear panel of the server. 2. Initiate a console session, and access the MP Main Menu. 3. Enter CM to enable command mode. 4. To use the remote power control command, enter PC. 5. To power on the server, enter ON, and enter YES when prompted to confirm the action. 6. Start the operating system. Powering On the Server Manually NOTE: If the power restore feature is set to Always On through the iLO MP PR command, the server automatically powers on to the full power state. To manually power on the server, follow these steps: 1. Plug all the power cables into the receptacles on the rear panel of the server. 2. To start the server, press the Power button. 3. Start the operating system. Powering Off the Server If the server is in the standby or full power state, power off the server using the following methods: • iLO MP PC command • Power button Powering Off the Server Using the iLO MP To power off the server using the iLO MP, follow these steps: 1. Gracefully shut down the operating system. 2. Initiate a console session, and access the MP Main Menu. Powering the Server On and Off 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
Table 1-17 Power States
DC Voltage
Applied?
Standby DC
Voltage
Applied?
Power Activated through the iLO MP
PC
Command; or Front Panel Power Button
Activated?
Power Cable
Plugged Into
Receptacle?
Power States
No
Yes
No
Yes
Standby power
Yes
Yes
Yes
Yes
Full power
No
No
No
No
Off
NOTE:
If the power restore feature is set to
Always On
through the iLO MP
PR
command, the
server automatically powers on to the full power state.
Powering On the Server
To power on the server to full power if the server is in the standby power state, use the following
methods:
•
iLO MP
PC
command
•
Power button
Powering On the Server Using the iLO MP
NOTE:
If the power restore feature is set to
Always On
through the iLO MP
PR
command, the
server automatically powers on to the full power state.
To power on the server using the iLO MP, follow these steps:
1.
Plug all the power cables into the receptacles on the rear panel of the server.
2.
Initiate a console session, and access the MP Main Menu.
3.
Enter
CM
to enable command mode.
4.
To use the remote power control command, enter
PC
.
5.
To power on the server, enter
ON
, and enter
YES
when prompted to confirm the action.
6.
Start the operating system.
Powering On the Server Manually
NOTE:
If the power restore feature is set to
Always On
through the iLO MP
PR
command, the
server automatically powers on to the full power state.
To manually power on the server, follow these steps:
1.
Plug all the power cables into the receptacles on the rear panel of the server.
2.
To start the server, press the Power button.
3.
Start the operating system.
Powering Off the Server
If the server is in the standby or full power state, power off the server using the following methods:
•
iLO MP
PC
command
•
Power button
Powering Off the Server Using the iLO MP
To power off the server using the iLO MP, follow these steps:
1.
Gracefully shut down the operating system.
2.
Initiate a console session, and access the MP Main Menu.
Powering the Server On and Off
39