HP rp3440 User Service Guide, Sixth Edition - HP 9000 rp3410/rp3440 - Page 51

Unpacking and Inspecting the Server, Verifying Site Preparation

Get HP rp3440 PDF manuals and user guides View all HP rp3440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Table 3-3 Installation Sequence Checklist (continued) Step Description 5 Set up the console. 6 Power on the server. 7 Access the console. 8 Boot the operating system. 9 Verify the server configuration. Completed Unpacking and Inspecting the Server This section describes procedures you perform before installation. Ensure that you have adequately prepared your environment for the new server, received the components that you ordered, and verified that the server and its containers are in good condition after shipment. Verifying Site Preparation Verifying site preparation is an essential factor of a successful server installation and includes the following tasks. 1. Gather LAN information and determine the two separate IP addresses for the iLO MP LAN and the system LAN. 2. Establish a method to connect to the server console. 3. Verify electrical requirements and ensure that grounding specifications and power requirements have been met. 4. Validate server physical space requirements. 5. Confirm environmental requirements. Inspecting the Shipping Containers for Damage HP shipping containers protect their contents under normal shipping conditions. After the equipment arrives, carefully inspect each carton for signs of shipping damage. Shipping damage constitutes moderate to severe damage, such as punctures in the corrugated carton, crushed boxes, or large dents. Normal wear or slight damage to the carton is not considered shipping damage. If you find shipping damage to the carton, contact your HP customer service representative immediately. Unpacking the Server To unpack a non-racked server, follow these steps. NOTE: HP recommends the use of a lifter, such as a RonI Company model 17000 SP 400 lifting device, when moving a non-racked server. 1. Use the instructions printed on the outside top flap of the carton; remove the banding and the outer carton from the server pallet. 2. Remove all inner accessory cartons and the top foam cushions, leaving only the server. IMPORTANT: Inspect each carton for shipping damage as you unpack the server. Checking the Inventory The sales order packing slip lists all of the equipment shipped from HP. Use this packing slip to verify that all of the equipment has arrived. Unpacking and Inspecting the Server 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
Table 3-3 Installation Sequence Checklist
(continued)
Completed
Description
Step
Set up the console.
5
Power on the server.
6
Access the console.
7
Boot the operating system.
8
Verify the server configuration.
9
Unpacking and Inspecting the Server
This section describes procedures you perform before installation. Ensure that you have adequately
prepared your environment for the new server, received the components that you ordered, and
verified that the server and its containers are in good condition after shipment.
Verifying Site Preparation
Verifying site preparation is an essential factor of a successful server installation and includes
the following tasks.
1.
Gather LAN information and determine the two separate IP addresses for the iLO MP LAN
and the system LAN.
2.
Establish a method to connect to the server console.
3.
Verify electrical requirements and ensure that grounding specifications and power
requirements have been met.
4.
Validate server physical space requirements.
5.
Confirm environmental requirements.
Inspecting the Shipping Containers for Damage
HP shipping containers protect their contents under normal shipping conditions. After the
equipment arrives, carefully inspect each carton for signs of shipping damage. Shipping damage
constitutes moderate to severe damage, such as punctures in the corrugated carton, crushed
boxes, or large dents. Normal wear or slight damage to the carton is not considered shipping
damage. If you find shipping damage to the carton, contact your HP customer service
representative immediately.
Unpacking the Server
To unpack a non-racked server, follow these steps.
NOTE:
HP recommends the use of a lifter, such as a RonI Company model 17000 SP 400 lifting
device, when moving a non-racked server.
1.
Use the instructions printed on the outside top flap of the carton; remove the banding and
the outer carton from the server pallet.
2.
Remove all inner accessory cartons and the top foam cushions, leaving only the server.
IMPORTANT:
Inspect each carton for shipping damage as you unpack the server.
Checking the Inventory
The sales order packing slip lists all of the equipment shipped from HP. Use this packing slip to
verify that all of the equipment has arrived.
Unpacking and Inspecting the Server
51