HP rp3440 User Service Guide, Sixth Edition - HP 9000 rp3410/rp3440 - Page 85

Replacing the System Battery, Battery Notice

Get HP rp3440 PDF manuals and user guides View all HP rp3440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

19. Replace the cover. (See "Removing and Replacing the Top Cover on a Rack-Mounted Server" (page 53).) 20. Reconnect the power and external cables and turn on the server. 21. Verify processor installation by using the system utilities. • Use the iLO MP commands to verify operation • Use the BCH commands to verify operation • Use MAKODIAG provided by the offline diagnostic environment to exercise the processor added Replacing the System Battery The server has two batteries. The main system battery is located on the system board. The other battery is located on the underside of the iLO MP card. Battery Notice This product contains a Lithium battery. WARNING! Lithium batteries can explode if mistreated. Do not recharge, disassemble, or dispose of lithium batteries in a fire. Failure to observe this warning can result in personal injury or damage to equipment. Replace only with the identical or equivalent battery. Follow the manufacturer's recommendations. Dispose of used batteries according to the manufacturer's instructions. Replacing the System Battery To replace the system battery, follow these steps: 1. Power off the server and disconnect the power and external cables. 2. Remove the cover. (See "Removing and Replacing Server Covers and Bezels" (page 52) for instructions.) 3. Remove the memory airflow guide (see "Removing and Replacing the Memory Airflow Guide" (page 65)). 4. Remove the processor airflow guide, the front portion of the processor airflow guide, and fans 1A and 1B (see "Removing and Replacing the Processor Airflow Guide" (page 66)). 5. Lift up the battery retaining clip with a flat-head screwdriver and push on the back of the battery to remove the battery from its holder. Installing Additional Components 85

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
19.
Replace the cover. (See
“Removing and Replacing the Top Cover on a Rack-Mounted Server”
(page 53)
.)
20.
Reconnect the power and external cables and turn on the server.
21.
Verify processor installation by using the system utilities.
•
Use the iLO MP commands to verify operation
•
Use the BCH commands to verify operation
•
Use
MAKODIAG
provided by the offline diagnostic environment to exercise the processor
added
Replacing the System Battery
The server has two batteries. The main system battery is located on the system board. The other
battery is located on the underside of the iLO MP card.
Battery Notice
This product contains a Lithium battery.
WARNING!
Lithium batteries can explode if mistreated. Do not recharge, disassemble, or
dispose of lithium batteries in a fire. Failure to observe this warning can result in personal injury
or damage to equipment.
Replace only with the identical or equivalent battery. Follow the manufacturer’s recommendations.
Dispose of used batteries according to the manufacturer's instructions.
Replacing the System Battery
To replace the system battery, follow these steps:
1.
Power off the server and disconnect the power and external cables.
2.
Remove the cover. (See
“Removing and Replacing Server Covers and Bezels” (page 52)
for
instructions.)
3.
Remove the memory airflow guide (see
“Removing and Replacing the Memory Airflow
Guide” (page 65)
).
4.
Remove the processor airflow guide, the front portion of the processor airflow guide, and
fans 1A and 1B (see
“Removing and Replacing the Processor Airflow Guide” (page 66)
).
5.
Lift up the battery retaining clip with a flat-head screwdriver and push on the back of the
battery to remove the battery from its holder.
Installing Additional Components
85