HP rp3440 User Service Guide, Sixth Edition - HP 9000 rp3410/rp3440 - Page 88

Applying Standby Power To the Server, Connecting To the LAN

Get HP rp3440 PDF manuals and user guides View all HP rp3440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 88 highlights

• LVD/SE SCSI port - The SCSI port is used to attach SCSI external mass storage to the server - Connections to the SCSI board include the external SCSI channels for external mass storage devices CAUTION: Some restrictions apply to the mass storage devices that can be connected to the core I/O SCSI HBA. External connections to the SCSI HBA core I/O controller are only supported when the internal cable between the SCSI backplane and the SCSI HBA core I/O card is disconnected. The server is shipped in simplex configuration which supports external devices. If you convert the server to duplex configuration, you cannot install external SCSI devices. • LAN Connection - The LAN board provides the basic external I/O connectivity for the server - One 10/100/1000 Base-T LAN RJ45 connector • One 15-pin VGA port. This port is currently disabled. DO NOT USE THE PORT. For graphics capability, install the accessory graphics PCI card (HP part number A6150B). WARNING! Ensure that the server is powered off and all the power sources have been disconnected from the server before attempting the following procedures. Voltage is present at various locations within the server whenever an AC power source is connected. This voltage is present even when the main power switch is in the off position. Failure to observe this warning can result in personal injury or damage to equipment. Applying Standby Power To the Server To apply standby power to the server, follow these steps: 1. If the server has one power supply installed in slot P1, plug the power cord into that receptacle. Plug the other end of the power cord into an appropriate outlet. NOTE: The LED on the power supply does not illuminate in the standby power state. The LED illuminates when the server is powered on to full power. If the power restore feature is set to Always On through the iLO MP PR command, the server automatically powers on to the full power state when the power cord is plugged into the server. 2. If the server has two power supplies, plug the second power cord into the power supply in slot P2. Plug the other end of the power cord into an appropriate outlet. Connecting To the LAN The server has the following ports that provide network connectivity: • iLO MP LAN port. Use this port to access the iLO MP through the LAN. • Console/Remote/UPS port (RS-232). Use this port to access the iLO MP through the console. Figure 3-48 shows the LAN ports on the server rear. 88 Installing the System

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
•
LVD/SE SCSI port
—
The SCSI port is used to attach SCSI external mass storage to the server
—
Connections to the SCSI board include the external SCSI channels for external mass
storage devices
CAUTION:
Some restrictions apply to the mass storage devices that can be connected to
the core I/O SCSI HBA. External connections to the SCSI HBA core I/O controller are only
supported when the internal cable between the SCSI backplane and the SCSI HBA core I/O
card is disconnected. The server is shipped in simplex configuration which supports external
devices. If you convert the server to duplex configuration, you cannot install external SCSI
devices.
•
LAN Connection
—
The LAN board provides the basic external I/O connectivity for the server
—
One 10/100/1000 Base-T LAN RJ45 connector
•
One 15-pin VGA port. This port is currently disabled. DO NOT USE THE PORT.
For graphics capability, install the accessory graphics PCI card (HP part number A6150B).
WARNING!
Ensure that the server is powered off and all the power sources have been
disconnected from the server before attempting the following procedures.
Voltage is present at various locations within the server whenever an AC power source is
connected. This voltage is present even when the main power switch is in the off position.
Failure to observe this warning can result in personal injury or damage to equipment.
Applying Standby Power To the Server
To apply standby power to the server, follow these steps:
1.
If the server has one power supply installed in slot P1, plug the power cord into that
receptacle. Plug the other end of the power cord into an appropriate outlet.
NOTE:
The LED on the power supply does not illuminate in the standby power state. The
LED illuminates when the server is powered on to full power. If the power restore feature
is set to Always On through the iLO MP
PR
command, the server automatically powers on
to the full power state when the power cord is plugged into the server.
2.
If the server has two power supplies, plug the second power cord into the power supply in
slot P2. Plug the other end of the power cord into an appropriate outlet.
Connecting To the LAN
The server has the following ports that provide network connectivity:
•
iLO MP LAN port. Use this port to access the iLO MP through the LAN.
•
Console/Remote/UPS port (RS-232). Use this port to access the iLO MP through the console.
Figure 3-48
shows the LAN ports on the server rear.
88
Installing the System